Yalcin Oguz Hetemoglu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yalcin Oguz Hetemoglu has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Burhan Alam
Middle East Technical University
1 shared publication Cagri Ozturk
Department of Civil Engineering Middle East Technical University Ankara Turkey
1 shared publication- Emin Sengun
Ankara Yildirim Beyazit Universitesi
1 shared publication - Halil Ceylan
Iowa State University
1 shared publication - Ismail Ozgur Yaman
Middle East Technical University
1 shared publication - Kürşat Çubuk
Gazi Üniversitesi
1 shared publication
Latest Publications
- 6 March 2025
- Published by Wiley in Structural Concrete
- Vol. 26 (5) , 5978-5998
Polypropylene fiber assessment for achieving optimal toughness in sustainable tunnel lining selection with various concrete matrices
This study evaluates the performance of polypropylene (PP) fiber‐reinforced concrete mixes for tunnel‐lining applications, using four concrete types: pervious, moderate strength, high‐performance, and ultra‐high‐performance. The mixes incorporate fiber dosages up to 1.0% by volume, except for ultra‐high‐performance concrete, which includes up to 2.7%. Performance is assessed through flexural tests on 72 panels, following european standard (EN) 14488‐5 and American society for testing and materials (ASTM) 1550 standards. The findings show that fiber addition boosts energy absorption in pervious concrete, but volumes under 9 kg/m 3 (Vf‐1%) do not meet toughness criteria. A 24 kg/m 3 (Vf‐2.7%) fiber dosage also falls short, suggesting a need for a stronger matrix. Statistical analysis produced precise prediction equations ( R 2 >92%) for energy absorption, factoring in cementitious materials, water‐to‐cement ratio, fiber dosage, and aggregate ratio. These equations serve as valuable tools for predicting the performance of fiber‐reinforced concrete (FRC) mixtures based on concrete composition and fiber dosages. Notably, both square and round panel tests demonstrate a strong correlation ( R 2 = 94%) with respect to energy absorption capacity, with the square panel test exhibiting values approximately 2.5 times higher. Assessment of toughness levels, material cost, and CO 2 emissions is carried out from a sustainability perspective, with the optimal choice emphasized as the normal‐performance FRC matrix incorporating 9 kg of PP fiber.
- 6 March 2025
- Published by Wiley in Structural Concrete
- Vol. 26 (5) , 5978-5998
Polypropylene fiber assessment for achieving optimal toughness in sustainable tunnel lining selection with various concrete matrices
This study evaluates the performance of polypropylene (PP) fiber‐reinforced concrete mixes for tunnel‐lining applications, using four concrete types: pervious, moderate strength, high‐performance, and ultra‐high‐performance. The mixes incorporate fiber dosages up to 1.0% by volume, except for ultra‐high‐performance concrete, which includes up to 2.7%. Performance is assessed through flexural tests on 72 panels, following european standard (EN) 14488‐5 and American society for testing and materials (ASTM) 1550 standards. The findings show that fiber addition boosts energy absorption in pervious concrete, but volumes under 9 kg/m 3 (Vf‐1%) do not meet toughness criteria. A 24 kg/m 3 (Vf‐2.7%) fiber dosage also falls short, suggesting a need for a stronger matrix. Statistical analysis produced precise prediction equations ( R 2 >92%) for energy absorption, factoring in cementitious materials, water‐to‐cement ratio, fiber dosage, and aggregate ratio. These equations serve as valuable tools for predicting the performance of fiber‐reinforced concrete (FRC) mixtures based on concrete composition and fiber dosages. Notably, both square and round panel tests demonstrate a strong correlation ( R 2 = 94%) with respect to energy absorption capacity, with the square panel test exhibiting values approximately 2.5 times higher. Assessment of toughness levels, material cost, and CO 2 emissions is carried out from a sustainability perspective, with the optimal choice emphasized as the normal‐performance FRC matrix incorporating 9 kg of PP fiber.
- Open Access
- 13 February 2025
- Published by MDPI AG in Construction Materials
- Vol. 5 (1) , 9
Improvement in Performance Characteristics of Bitumen and Bituminous Mixtures by Means of Polyvinyl Acetate
This paper examines the improvement in the performance characteristics and the rheological properties of modified bitumen through the addition of the thermoplastic polymer polyvinyl acetate (PVA). PVA is a synthetic polymer derived from the polymerization of the vinyl acetate. The effect of PVA on bitumen and bituminous mixtures was investigated through the conventional (penetration, softening point, force-ductility, elastic recovery, Marshall and Nicholson stripping tests) and Superpave (rotational viscosity (RV), rolling thin film oven (RTFOT), pressure aging vessel (PAV), dynamic shear rheometer (DSR) and beam bending rheometer (BBR)) tests. PVA was added to bitumen at rates of 2%, 4%, 6% and 8% by mass. Based on the bitumen test results, a PVA rate of 6% was selected for the mixture tests. The modification process was carried out at relatively low temperature (150 °C) and mixing time (20 min) based on various trials, considering the short-term aging of the bitumen. With PVA modification, the penetration value of the bitumen decreased while the softening point increased. As a result, the calculated penetration index (PI) increased and the thermal sensitivity of the bitumen decreased. Significant improvements were detected in elastic recovery and force-ductility tests. Additionally, PVA improved the resistance of asphalt to settling and cracking. Similar results were observed in the DSR and BBR tests. Furthermore, the stripping resistance increased and the stability value improved significantly in the mixture tests.
- 13 February 2025
- Published by MDPI AG in Construction Materials
- Vol. 5 (1) , 9
Open AccessImprovement in Performance Characteristics of Bitumen and Bituminous Mixtures by Means of Polyvinyl Acetate
This paper examines the improvement in the performance characteristics and the rheological properties of modified bitumen through the addition of the thermoplastic polymer polyvinyl acetate (PVA). PVA is a synthetic polymer derived from the polymerization of the vinyl acetate. The effect of PVA on bitumen and bituminous mixtures was investigated through the conventional (penetration, softening point, force-ductility, elastic recovery, Marshall and Nicholson stripping tests) and Superpave (rotational viscosity (RV), rolling thin film oven (RTFOT), pressure aging vessel (PAV), dynamic shear rheometer (DSR) and beam bending rheometer (BBR)) tests. PVA was added to bitumen at rates of 2%, 4%, 6% and 8% by mass. Based on the bitumen test results, a PVA rate of 6% was selected for the mixture tests. The modification process was carried out at relatively low temperature (150 °C) and mixing time (20 min) based on various trials, considering the short-term aging of the bitumen. With PVA modification, the penetration value of the bitumen decreased while the softening point increased. As a result, the calculated penetration index (PI) increased and the thermal sensitivity of the bitumen decreased. Significant improvements were detected in elastic recovery and force-ductility tests. Additionally, PVA improved the resistance of asphalt to settling and cracking. Similar results were observed in the DSR and BBR tests. Furthermore, the stripping resistance increased and the stability value improved significantly in the mixture tests.