HKHemantkumar H. Kadam

Hemantkumar H. Kadam

*This is an algorithmically generated author record based on publicly available information.

Hemantkumar H. Kadam has a total of 13 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Experimental Insights Into the Role of Rhamnolipid as a Bio‐Surfactants on Thermo‐Physical Behavior of Alumina

    by Amol V. Suryavanshi, Hemantkumar H. Kadam, Narendra R. Deore, Abhijeet N. Kore, Ashok T. Pise

    Although bio‐surfactants have attracted growing interest, their application in heat transfer enhancement remains less explored than synthetic surfactants, particularly, regarding their effects on nanofluid thermophysical properties. This study investigates the influence of the bio‐surfactant rhamnolipid (RHL) on the density, specific heat capacity, viscosity, and thermal conductivity of Al 2 O 3 /distilled water nanofluids. Nanofluids containing 0.02–0.3 wt% Al 2 O 3 nanoparticles were prepared with RHL concentrations ranging from 200 to 600 ppm to improve short‐term stability. Experimental results showed that density exhibited only marginal changes with nanoparticle concentration, indicating a negligible effect of RHL on mass‐related properties. The addition of RHL slightly reduced specific heat capacity due to improved nanoparticle dispersion and interfacial interactions. A significant reduction in viscosity was observed, with a maximum decrease of 29.41% at 0.1 wt% Al 2 O 3 and 550 ppm RHL. Thermal conductivity increased substantially, reaching a maximum enhancement of 6.95% at the same concentration, attributed to improved dispersion stability and reduced thermal resistance. These findings demonstrate that RHL is a promising eco‐friendly surfactant for improving the thermophysical characteristics and heat transfer potential of Al 2 O 3 ‐based nanofluids.

  • Experimental investigation of heat transfer characteristics of rhamnolipid-based Al2O3 nanofluids in vertical tube subcooled flow boiling

    by Hemantkumar H. Kadam, Sucheta S. Kakde, Ajit Patil, Narendra R. Deore, Sagar R. Wankhede, Siddhanath V. Nishandar, Ashok T. Pise

  • Numerical Analysis of Helical Coil‐Inserted Tubes Based on Thermohydraulic Performance and Development of Correlations for Heat and Fluid Flow

    by Sanjay Kadam, Abhijeet N. Kore, Sachin Sawant, Hemant Kadam, Suhas Mohite

    This study presents a numerical investigation on the thermohydraulic performance of tubes fitted with wire coil inserts under turbulent flow conditions to enhance heat transfer (HT) efficiency in compact thermal systems. Conventional smooth tubes face limitations due to boundary‐layer formation, which resists convective HT; therefore, wire coil inserts are employed to disrupt this layer and increase turbulence. The objective of this research is to determine the influence of wire coil geometry on HT and pressure drop and to develop empirical correlations for predicting the Nusselt number and friction factor. Numerical simulations were carried out using ANSYS Fluent with the renormalization group k – ε turbulence model validated against the Dittus–Boelter correlation. Water was used as the working fluid, and wire coil diameters of 0.5, 1, and 1.5 mm with pitches of 21, 24, 28, and 31 mm were analyzed for Reynolds numbers ranging from 4500 to 9000. Results indicated that a wire coil of 1 mm diameter and 24 mm pitch provided the best combination of HT enhancement and moderate pressure drop, achieving an average Nusselt number improvement of about 110% compared with a smooth tube. The thermohydraulic performance factor ranged between 1.62 and 1.20, confirming significant enhancement up to a Reynolds number of 10,000. Regression‐based correlations for Nusselt number and friction factor were developed, showing strong agreement with simulation data ( R 2 = 0.94 and 0.89, respectively). The developed correlations serve as reliable tools for predicting the performance of coil‐inserted tubes in practical heat exchanger design.


  • Experimental Study: An Effect of Rhamnolipid Bio‐Surfactant on Heat Transfer Performance of Al 2 O 3 Nanofluids in Horizontal Tube

    by Hemantkumar H. Kadam, Ashok T. Pise, Abhijeet N. Kore

    The utilization of bio‐surfactants in heat transfer enhancement studies remains underexplored compared to synthetic surfactants. This study investigates the effects of Rhamnolipid, a bio‐surfactant, on the thermal performance of distilled water (DW) and Al 2 O 3 water‐based nanofluids (NFs). Rhamnolipid concentrations ranging from 200 to 600 ppm and nanoparticle (NP) concentrations from 0.02 to 0.5 wt.% were studied. The addition of Rhamnolipid to distilled water resulted in the maximization of Thermal Conductivity (TC) at 300 ppm, which aligns with the critical micelle concentration (CMC), leading to a 19.46% improvement in the heat transfer coefficient (HTC). Al 2 O 3 NPs alone showed a 32.07% HTC enhancement at 0.05 wt.% concentration, although the performance declined after a few hours due to particle sedimentation. When Rhamnolipid and NPs were combined, HTC increased with Rhamnolipid concentrations up to 550 ppm, after which the performance declined. The combined addition resulted in maximum enhancement of 92.88% HTC at 0.1 wt.% concentrated nanofluid with 550 ppm RHL. These findings demonstrate that eco‐friendly bio‐surfactants, such as Rhamnolipid, can serve as effective surfactants for enhancing heat conduction performance in NFs.


  • Influence of rhamnolipids, anionic surfactants, and Al2O3 nanoparticles on the viscosity of distilled water‐based fluids: A comparative experimental study

    by Hemantkumar H. Kadam, Ashok T. Pise

    This experimental study examines the effect of different surfactants—sodium lauryl sulfate (SLS), sodium dodecyl sulfate (SDS), and bio‐surfactant rhamnolipids (RHL)—on the viscosity of distilled water (DW) with varying concentrations of aluminium oxide (Al2O₃) nanoparticles (NPs). Al2O₃ NPs were used in concentrations ranging from 0.02 to 0.5 wt%, while surfactant concentrations ranged from 2000 to 4000 ppm for SDS and SLS and from 200 to 600 ppm for RHL. Viscometric experiments revealed that the type and concentration of surfactants, along with the NP loading, influenced the viscosity of nanofluids (NFs). NFs without surfactant exhibited consistently higher viscosities compared with DW with surfactant alone. At 0.5 wt% Al2O3, NF viscosity was 17% higher than SDS and RHL and 9% higher than SLS. Interestingly, in DW with both surfactant and NPs, viscosity initially decreased with increasing Al2O3 concentration, followed by a rapid increase after 0.1 wt%. These results offer insights into the interaction between surfactants and NPs, relevant for industries requiring precise viscosity control, such as pharmaceuticals, cosmetics, and environmental applications.


  • A thorough analysis of surfactant addition effects on the thermophysical properties and stability of nanofluids

    by H. H. Kadam, A. T. Pise

    Researchers are mainly suggesting that optimizing the heat efficiency of thermal apparatus by dispersing nanoparticles into the foundation fluid will boost its heat efficiency in boiling sectors. Many investigators conduct research on factors such as fluid properties, bubble growth and bubble dynamics, heater surface effect, and so forth. However, the problem of deficiency in stability created by nanoparticle sedimentation or agglomeration into the base fluid over time has restricted practicable applications, which has drawn considerable attention in recent years. To overcome that, many researchers used a common technique, the addition of stabilizing agents like surfactants/additives into the nanofluids (NFs) to achieve stability. Understanding the behavior of surfactants in NFs and their effect on various important physical properties of the working fluid is required. In this review, firstly discuss the impact of adding surfactants on the stability of an aqueous solution. Additionally, it provides a concise assessment of how the inclusion of surfactants affects different thermal physical characteristics like interfacial tension, viscosity, and thermal conductivity of aqueous solutions or NFs. Finally, it outlines the primary obstacles and challenges encountered by researchers that continue to be areas of focus for future investigations concerning NFs containing surfactants.