Seohyeon Park
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Seohyeon Park has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Hagyoul Bae
Jeonbuk National University
8 shared publications - Minah Park
Jeonbuk National University
7 shared publications - Seongbin Lim
Division of Electronic Engineering, Jeonbuk National University, Jeonju, Republic of Korea
7 shared publications - Sojin Jung
Division of Electronic Engineering, Jeonbuk National University, Jeonju, Republic of Korea
7 shared publications - Hongseung Lee
Jeonbuk National University
4 shared publications - Hyeonjun Song
Department of Electronic Engineering, Jeonbuk National University 1 , Jeonju-si 54896
4 shared publications
Latest Publications
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (11) , 6976-6982
Performance Enhancement of a-IGZO TFTs With Elevated Source/Drain Structure via Channel Trench Etching
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (11) , 6976-6982
Performance Enhancement of a-IGZO TFTs With Elevated Source/Drain Structure via Channel Trench Etching
- 18 May 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (20)
Localized electrothermal annealing for rapid recovery of ambient degradation in indium oxide transistors via COMSOL simulations and experimental characterization
This work reports an electrothermal annealing (ETA) technique based on localized Joule heat for effective recovery of the electrical characteristics of indium oxide (In2O3) thin-film transistors (TFTs) that are degraded by ambient exposure. We investigated the current–voltage (I–V) characteristics, resistance, subthreshold swing, and μFE under three conditions: the initial state, the degraded state after 10 days, and the state after ETA. X-ray photoelectron spectroscopy and subgap density-of-states analyses were conducted to examine variations in oxygen vacancy (VO) quantitatively and thereby demonstrate the effects of ETA. Additionally, COMSOL simulations were performed to elucidate the temperature distribution induced by localized Joule heat and to validate the feasibility of reducing shallow trap states via ETA in In2O3 TFTs.
- 18 May 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (20)
Localized electrothermal annealing for rapid recovery of ambient degradation in indium oxide transistors via COMSOL simulations and experimental characterization
This work reports an electrothermal annealing (ETA) technique based on localized Joule heat for effective recovery of the electrical characteristics of indium oxide (In2O3) thin-film transistors (TFTs) that are degraded by ambient exposure. We investigated the current–voltage (I–V) characteristics, resistance, subthreshold swing, and μFE under three conditions: the initial state, the degraded state after 10 days, and the state after ETA. X-ray photoelectron spectroscopy and subgap density-of-states analyses were conducted to examine variations in oxygen vacancy (VO) quantitatively and thereby demonstrate the effects of ETA. Additionally, COMSOL simulations were performed to elucidate the temperature distribution induced by localized Joule heat and to validate the feasibility of reducing shallow trap states via ETA in In2O3 TFTs.
- 25 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. PP (07413106) , 1
Simultaneous Observation of Donor- and Acceptor-like Interface Trap Density in 5-Stage Si-NW GAA FETs Using Polychromatic Photonic I-V Characteristics
In this study, we analyzed the interface trap density (Dit) of 5-stage silicon-nanowires (Si-NWs) gate-all-around (GAA) field-effect-transistors (FETs) using polychromatic photonic current-voltage technique in a single device. We modeled photoresponsive differential body factor as a function of gate voltage (VGS) and extracted donor-like Dit (Dit_D) derived from the difference in the photoresponsive differential body factors. In contrast, acceptor-like Dit (Dit_A) was extracted at the dark state. Dit_D and Dit_A are extracted under two different VGS regions: Dit_A for between the flat band voltage (VFB) and the threshold voltage (VT), and Dit_D for between Von and VFB. Accordingly, positive-bias-stress (PBS) was applied to analyze the change in Dit before and after PBS.
- 25 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. PP (07413106) , 1
Simultaneous Observation of Donor- and Acceptor-like Interface Trap Density in 5-Stage Si-NW GAA FETs Using Polychromatic Photonic I-V Characteristics
In this study, we analyzed the interface trap density (Dit) of 5-stage silicon-nanowires (Si-NWs) gate-all-around (GAA) field-effect-transistors (FETs) using polychromatic photonic current-voltage technique in a single device. We modeled photoresponsive differential body factor as a function of gate voltage (VGS) and extracted donor-like Dit (Dit_D) derived from the difference in the photoresponsive differential body factors. In contrast, acceptor-like Dit (Dit_A) was extracted at the dark state. Dit_D and Dit_A are extracted under two different VGS regions: Dit_A for between the flat band voltage (VFB) and the threshold voltage (VT), and Dit_D for between Von and VFB. Accordingly, positive-bias-stress (PBS) was applied to analyze the change in Dit before and after PBS.
- 10 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (3) , 1647-1655
High- κ Capping Layer Effects on Carrier Polarity and Reliability of SWNT Field Effect Transistors With Spin-on-Glass Buffer Layer
The electrical performance and reliability of spin-on-glass (SOG)/high- $\kappa $ single-walled carbon-nanotube (SWNT) field-effect transistors (FETs) were examined through the dual-gate operation, pulsed-bias measurements, and low-frequency-noise (LFN) analyses. Hysteresis and bias-stress instabilities are governed by interface-trap dynamics, where Al2O3 forms shallow fast traps, HfO2 exhibits the moderate activity, and ZrO2 introduces deep slow traps affecting long-term stability. Devices with HfO2 capping showed minimal hysteresis (~0.1 V), while ZrO2-based transistors achieved the highest field-effect mobility (~35 cm ${}^{{2}}~ \cdot $ V ${}^{-{1}}~\cdot $ s ${}^{-{1}}\text {)}$ and the lowest contact resistance. Under ±3-V gate stress, electron trapping dominated ( $\Delta {V}_{\text {TH}} \approx ~0.6$ –0.9 V), whereas the hole trapping was effectively suppressed dues to large injection barriers ( $\approx$ 2.5–3.4 eV). The noise spectra followed the carrier-number-fluctuation (CNF) model, confirming the trap-density order Al2O ${}_{{3}} \gt $ HfO ${}_{{2}} \gt $ ZrO2. All fabrication steps were performed below $250~^{\circ }$ C, ensuring compatibility with monolithic 3-D (M3D) and system-in-package (SiP) platforms for reliable, low-power SWNT electronics targeting sub-3-nm nodes.
- 10 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (3) , 1647-1655
High- κ Capping Layer Effects on Carrier Polarity and Reliability of SWNT Field Effect Transistors With Spin-on-Glass Buffer Layer
The electrical performance and reliability of spin-on-glass (SOG)/high- $\kappa $ single-walled carbon-nanotube (SWNT) field-effect transistors (FETs) were examined through the dual-gate operation, pulsed-bias measurements, and low-frequency-noise (LFN) analyses. Hysteresis and bias-stress instabilities are governed by interface-trap dynamics, where Al2O3 forms shallow fast traps, HfO2 exhibits the moderate activity, and ZrO2 introduces deep slow traps affecting long-term stability. Devices with HfO2 capping showed minimal hysteresis (~0.1 V), while ZrO2-based transistors achieved the highest field-effect mobility (~35 cm ${}^{{2}}~ \cdot $ V ${}^{-{1}}~\cdot $ s ${}^{-{1}}\text {)}$ and the lowest contact resistance. Under ±3-V gate stress, electron trapping dominated ( $\Delta {V}_{\text {TH}} \approx ~0.6$ –0.9 V), whereas the hole trapping was effectively suppressed dues to large injection barriers ( $\approx$ 2.5–3.4 eV). The noise spectra followed the carrier-number-fluctuation (CNF) model, confirming the trap-density order Al2O ${}_{{3}} \gt $ HfO ${}_{{2}} \gt $ ZrO2. All fabrication steps were performed below $250~^{\circ }$ C, ensuring compatibility with monolithic 3-D (M3D) and system-in-package (SiP) platforms for reliable, low-power SWNT electronics targeting sub-3-nm nodes.
- 18 August 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (7)
Advanced characterization of density-of-states over wide bandgap-energy in p-type Cu2O TFTs by multiple-wavelength light source
In this study, we fabricated thin-film transistors by depositing Cu2O through plasma-enhanced atomic layer deposition (3.6 k cycles), which has the advantages of enhanced chemical reactivity and improved crystal structure of thin films compared to conventional atomic layer deposition. We analyzed traps near the valence band using multi-wavelength light that extended up to the above bandgap, in conjunction with dark-state measured data. Using multi-wavelength light, we extracted traps dependent on the gate voltage. Traps with underestimated density due to limited detectability within the bandgap, dependent on the energy levels of the wavelengths, are filled with photons to extract the captured traps (holes). Our results reveal that the energy-dependent density peaks of VCu and VO, which strongly influence the p-type conduction mechanism, were observed in the trap density near the Fermi level using multiwavelength I–V photo-response. This study reports photo-responsive I–V measurements in aggressively scaled devices, crucial for instability and reliability assessments. Furthermore, trap extraction plays a critical role in the effective integration of n-type oxide semiconductors into CMOS technology, providing valuable insights into the performance analysis of applications.
- 18 August 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (7)
Advanced characterization of density-of-states over wide bandgap-energy in p-type Cu2O TFTs by multiple-wavelength light source
In this study, we fabricated thin-film transistors by depositing Cu2O through plasma-enhanced atomic layer deposition (3.6 k cycles), which has the advantages of enhanced chemical reactivity and improved crystal structure of thin films compared to conventional atomic layer deposition. We analyzed traps near the valence band using multi-wavelength light that extended up to the above bandgap, in conjunction with dark-state measured data. Using multi-wavelength light, we extracted traps dependent on the gate voltage. Traps with underestimated density due to limited detectability within the bandgap, dependent on the energy levels of the wavelengths, are filled with photons to extract the captured traps (holes). Our results reveal that the energy-dependent density peaks of VCu and VO, which strongly influence the p-type conduction mechanism, were observed in the trap density near the Fermi level using multiwavelength I–V photo-response. This study reports photo-responsive I–V measurements in aggressively scaled devices, crucial for instability and reliability assessments. Furthermore, trap extraction plays a critical role in the effective integration of n-type oxide semiconductors into CMOS technology, providing valuable insights into the performance analysis of applications.
- 7 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (7) , 1103-1106
Exploration of Interplay Between Charge Trapping Dynamics and Polarization Switching in α -In₂Se₃ Ferroelectric Semiconductor FETs
The trap behavior in a two-dimensional (2D) ferroelectric semiconductor (FeS) field-effect transistors (FETs) that can overcome the device scaling limit of conventional ferroelectric FETs was analyzed. The conventional ferroelectric FETs exhibit a counterclockwise hysteresis loop, whereas ferroelectric channel-based FETs with high effective oxide thickness exhibit a clockwise hysteresis loop. Therefore, it is challenging to determine the contribution of ferroelectric polarization switching and trap states to the current conduction of FeS-FETs and to quantify their respective impacts, owing to their complex interaction. The modified conductance method with a four-element equivalent circuit model was employed to analyze the behavior of intrinsic trap states, with parasitic capacitance de-embedded, depending on the FeS polarization switching states. As a result, we confirmed that over the full energy range trap density can be extracted by unique characteristics of FeS-FETs. The retention characteristic was maintained at over 70 % of the initial memory on/off ratio when extrapolated to 104 s. Based on these results, guidelines for undefined trap state behavior of 2D α-In2Se3 FeS-FETs were presented.
- 7 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (7) , 1103-1106
Exploration of Interplay Between Charge Trapping Dynamics and Polarization Switching in α -In₂Se₃ Ferroelectric Semiconductor FETs
The trap behavior in a two-dimensional (2D) ferroelectric semiconductor (FeS) field-effect transistors (FETs) that can overcome the device scaling limit of conventional ferroelectric FETs was analyzed. The conventional ferroelectric FETs exhibit a counterclockwise hysteresis loop, whereas ferroelectric channel-based FETs with high effective oxide thickness exhibit a clockwise hysteresis loop. Therefore, it is challenging to determine the contribution of ferroelectric polarization switching and trap states to the current conduction of FeS-FETs and to quantify their respective impacts, owing to their complex interaction. The modified conductance method with a four-element equivalent circuit model was employed to analyze the behavior of intrinsic trap states, with parasitic capacitance de-embedded, depending on the FeS polarization switching states. As a result, we confirmed that over the full energy range trap density can be extracted by unique characteristics of FeS-FETs. The retention characteristic was maintained at over 70 % of the initial memory on/off ratio when extrapolated to 104 s. Based on these results, guidelines for undefined trap state behavior of 2D α-In2Se3 FeS-FETs were presented.
- 1 March 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (12)
Determination of donor- and acceptor-like interface trap density using photoresponsive GIDL in vertically stacked Si-NW GAA FETs
This work reports an effective technique that is proposed for the simultaneous extraction of the energy distribution of donor- and acceptor-like interface trap states [Dit,D(E) and Dit,A(E)] over a wide range of bandgap energies using a single current–voltage (I–V) measurement in vertically stacked silicon nanowire (Si-NW) gate-all-around field-effect transistors. In the proposed method, we analyzed Dit,D(E) and Dit,A(E) based on the trap-induced photoresponsive gate-induced drain leakage with sub-bandgap optical source (Eph = hν < Eg) at VGS ≪ VFB and differential body factor technique in the subthreshold current at VFB < VGS < VT, respectively.
- 1 March 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (12)
Determination of donor- and acceptor-like interface trap density using photoresponsive GIDL in vertically stacked Si-NW GAA FETs
This work reports an effective technique that is proposed for the simultaneous extraction of the energy distribution of donor- and acceptor-like interface trap states [Dit,D(E) and Dit,A(E)] over a wide range of bandgap energies using a single current–voltage (I–V) measurement in vertically stacked silicon nanowire (Si-NW) gate-all-around field-effect transistors. In the proposed method, we analyzed Dit,D(E) and Dit,A(E) based on the trap-induced photoresponsive gate-induced drain leakage with sub-bandgap optical source (Eph = hν < Eg) at VGS ≪ VFB and differential body factor technique in the subthreshold current at VFB < VGS < VT, respectively.
- 10 February 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (6)
Low-frequency noise and DC I–V characterization of gamma-ray irradiation-induced degradation and trap behaviors in a-IGZO TFTs
This work reports the impact of gamma-ray (γ-ray) irradiation-induced degradation based on the trap behaviors in amorphous indium-gallium-zinc-oxide (a-IGZO) thin-film transistors. By employing multiple measurement configurations via low-frequency noise and direct current I–V characterization, we quantitatively investigated the energetic distribution of subgap density-of-states in the a-IGZO channel and the spatial distribution of oxide traps (Not) in the gate insulator, respectively. Also, the qualitative analysis was performed to determine the oxygen-related defects after γ-ray irradiation using x-ray photoelectron spectroscopy. Furthermore, the validity of our results was additionally confirmed by measuring the breakdown voltage and applying positive-bias stress to the fabricated devices exposed to radiation for accelerated tests.
- 10 February 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (6)
Low-frequency noise and DC I–V characterization of gamma-ray irradiation-induced degradation and trap behaviors in a-IGZO TFTs
This work reports the impact of gamma-ray (γ-ray) irradiation-induced degradation based on the trap behaviors in amorphous indium-gallium-zinc-oxide (a-IGZO) thin-film transistors. By employing multiple measurement configurations via low-frequency noise and direct current I–V characterization, we quantitatively investigated the energetic distribution of subgap density-of-states in the a-IGZO channel and the spatial distribution of oxide traps (Not) in the gate insulator, respectively. Also, the qualitative analysis was performed to determine the oxygen-related defects after γ-ray irradiation using x-ray photoelectron spectroscopy. Furthermore, the validity of our results was additionally confirmed by measuring the breakdown voltage and applying positive-bias stress to the fabricated devices exposed to radiation for accelerated tests.