Larissa Juliana Sirtuli
Research Subjects
Research Interests
Larissa Juliana Sirtuli has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Denis Boing
Brusque University Center
2 shared publications - Susanne Norgren
Division of Applied Materials Science, Department of Engineering Sciences, The Ångström Laboratory, Uppsala University, Box 534, 751 21 Uppsala, Sweden
2 shared publications - Amol Thakare1 shared publication
- Claudio Abilio da Silveira
Instituto Federal de Santa Catarina
1 shared publication Fredrik Lindberg
1 shared publication- Jonas Östby
Sandvik Coromant R&D, 811 34 Sandviken, Sweden
1 shared publication
Latest Publications
- Open Access
- 18 May 2026
- Published by Elsevier in SSRN Electronic Journal
Influence of α-Al2O3 texture on residual stress, cooling cracks and hardness in CVD α-Al2O3/ Ti(C,N) coatings on cemented carbide
CVD α-Al2O3 coatings on cemented carbides are widely used in steel turning, where cutting tool performance is strongly dependent on the crystallographic texture of the α-Al2O3 layer. Residual stress, cooling-crack density, and hardness are key factors influencing coating integrity during machining. Although texture has been reported to affect these properties, trends remain inconsistent in the literature. In this work, three CVD α-Al2O3/Ti(C,N) coatings with identical architecture, substrate, and processing route, but distinct α-Al2O3 textures: i. c-plane (0001) , ii. r-plane (01-12) , and iii. a-plane (11-20) were investigated to isolate the role of texture under controlled conditions. The (0001) coating exhibited the highest tensile residual stress and the lowest crack density, while the (01-12) and (11-20) coatings showed lower stresses and denser crack network. This behaviour is consistent with a texture-dependent thermal expansion mismatch, complemented by orientation-dependent stress accommodation during cooling. The (01-12) and (11-20) textures, with a greater in-plane contribution of the c-axis, develop higher intrinsic thermal stress and thus promote more extensive crack formation for stress relaxation compared to texture. Nanohardness values were comparable across the three textures. The results demonstrate that α-Al2O3 texture has a clear influence on residual stress and cracking, but a limited effect on hardness. These findings provide a more consistent basis for interpreting texture–property relationships and suggest that the performance of (0001)-textured coatings in steel turning is primarily associated with reduced crack density and their response under directional loading, rather than with differences in hardness.
- 18 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessInfluence of α-Al2O3 texture on residual stress, cooling cracks and hardness in CVD α-Al2O3/ Ti(C,N) coatings on cemented carbide
CVD α-Al2O3 coatings on cemented carbides are widely used in steel turning, where cutting tool performance is strongly dependent on the crystallographic texture of the α-Al2O3 layer. Residual stress, cooling-crack density, and hardness are key factors influencing coating integrity during machining. Although texture has been reported to affect these properties, trends remain inconsistent in the literature. In this work, three CVD α-Al2O3/Ti(C,N) coatings with identical architecture, substrate, and processing route, but distinct α-Al2O3 textures: i. c-plane (0001) , ii. r-plane (01-12) , and iii. a-plane (11-20) were investigated to isolate the role of texture under controlled conditions. The (0001) coating exhibited the highest tensile residual stress and the lowest crack density, while the (01-12) and (11-20) coatings showed lower stresses and denser crack network. This behaviour is consistent with a texture-dependent thermal expansion mismatch, complemented by orientation-dependent stress accommodation during cooling. The (01-12) and (11-20) textures, with a greater in-plane contribution of the c-axis, develop higher intrinsic thermal stress and thus promote more extensive crack formation for stress relaxation compared to texture. Nanohardness values were comparable across the three textures. The results demonstrate that α-Al2O3 texture has a clear influence on residual stress and cracking, but a limited effect on hardness. These findings provide a more consistent basis for interpreting texture–property relationships and suggest that the performance of (0001)-textured coatings in steel turning is primarily associated with reduced crack density and their response under directional loading, rather than with differences in hardness.