Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Kaida Cai has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Microscopic Discharge Characteristics and Experimental Investigation of Atmospheric-Pressure Air Dielectric Barrier Discharge

    by Shaoting Li, Kaida Cai, Zuzhao Kang, Jing Xiao

    To elucidate the microscopic evolution characteristics of atmospheric-pressure air dielectric barrier discharge (DBD) under different voltage amplitudes, this study systematically investigates the discharge behavior of an atmospheric-pressure air DBD with a double-dielectric parallel-plate configuration by combining equivalent-circuit analysis, fluid-based numerical simulation, and experimental measurements. First, an equivalent-circuit model of the DBD, incorporating the dielectric capacitance, gap capacitance, and time-varying plasma resistance, is established to analyze the dynamic relationships among the applied voltage, gap voltage, and conduction current. Subsequently, a one-dimensional N2/O2 fluid plasma model is developed in COMSOL Multiphysics to systematically examine the effects of voltage amplitudes of 10, 12, 14, 16, and 18 kV on the spatiotemporal distributions of electron density, as well as on the gap voltage, conduction current, electric field strength in the gap, and electron temperature. The results show that, with increasing applied voltage, electron avalanche ionization is significantly enhanced, and both the electron density and current peak increase overall, although their marginal gains gradually diminish. At 14 kV, the region of high electron density effectively extends from the dielectric interface to most of the discharge gap, and the discharge exhibits a higher plasma filling degree and good cycle-to-cycle repeatability. Further analysis based on normalized curves and the Kneedle knee-point criterion reveals that the critical transition points of both the peak gap voltage and the peak conduction current are located at 14 kV, indicating that this condition represents a characteristic operating point within the investigated voltage range. Finally, a spatiotemporal evolution analysis of a single steady-state microdischarge pulse demonstrates that the DBD undergoes the stages of pre-ionization, avalanche ionization, electric-field reconstruction, surface charge deposition, and afterglow decay, and that the coupled effects of space charge and surface charge constitute the key mechanism governing discharge stability. The experimental results are in good agreement with the simulation findings, providing a theoretical basis for the parametric optimization and design of atmospheric-pressure air DBD systems.

  • Open Access

    Design of Dielectric Barrier Discharge Plasma Power Supply System Based on Zero-Voltage Switching Control Strategy

    by Xinmin Xie, Jing Xiao, Kaida Cai, Zuzhao Kang, Shaoting Li

    To address the issues of high switching losses in power devices and device temperature rise caused by hard switching in conventional plasma power supplies, this study presents a dielectric barrier discharge plasma power supply system based on a zero-voltage switching (ZVS) control strategy. First, the design of the plasma power supply input module, the plasma drive control board, the high-frequency transformer, and the dielectric barrier discharge load is presented. Next, a phase-shifted full-bridge topology simulation model based on the ZVS control strategy is developed using PLECS, and the optimal combination of parameters—including duty cycle, phase shift, resonant inductance, and dead time—is discussed. Subsequently, experimental tests are conducted on the dielectric barrier discharge plasma power supply system, with analyses focusing on the soft-switching waveforms of the power devices under the ZVS control strategy and the performance of the dielectric barrier discharge plasma generator load. Experimental results demonstrate that within the proposed system, the plasma exhibits a uniform distribution. Furthermore, junction temperature measurements of the power devices on the circuit board using a temperature tester show that the temperature rise remains within a reasonable range, thereby validating the feasibility of the designed dielectric barrier discharge plasma power supply system.

  • Open Access

    Research on a High-Frequency High-Voltage Plasma Power Supply Based on SPWM Modulation

    by Weimin Qin, Kaida Cai, Xiao Guo, Zixiong Yan, Minghui Yun, Jing Xiao

    Plasma power supplies find extensive applications across industrial, energy, environmental, and medical domains. This study addresses limitations of conventional plasma power supplies, including high harmonic current content, neutral-point potential imbalance, and manufacturing complexity. A novel design approach for high-frequency, high-voltage plasma power supplies is proposed, based on three-level sinusoidal pulse width modulation (SPWM) technology. First, the design distinctions between the input-side Boost power factor correction circuit and Diode Rectifier circuits are analyzed. Subsequently, an integrated SPWM driver-controller architecture and a design methodology for high-frequency transformers are introduced. A single-phase three-level SPWM modulation strategy is then presented. Based on this modulation technique, a high-frequency, high-voltage plasma power supply prototype incorporating air pumps and rotary motors was developed. Experimental validation demonstrated stable generation of plasma gas at a frequency of 25 kHz, with an output voltage of 10.79 kV and an output power of 1.75 kW. Results indicate that the refined power supply enhances electrical utilization efficiency, resolves neutral-point imbalance issues, and simplifies manufacturing through its integrated driver-controller design. This work offers a valuable reference for advancing high-frequency, high-voltage plasma technologies.

  • Open Access

    Structural Optimization and SVPWM Control Strategy of Rotary Motors for Plasma Spraying Applications

    by Lvying Liang, Kaida Cai, Lin Zhang, Zhihuan Tang, Jing Xiao

    This study systematically investigates the structural optimization and control strategies of a plasma power supply-based rotating electrical machine. Firstly, stress simulation analysis was conducted on both conventional and optimized motor structures using ANSYS 2025 R1 software. The results demonstrate the maximum stress at the motor bearings decreased from 1.295 MPa to 0.865 MPa after optimization, representing a 33.2% reduction. Secondly, dynamic balance simulation performed with Adams 2024 software revealed that the centroid offset range of the optimized motor was reduced from ±0.05 mm to ±0.0175 mm, achieving a 65% improvement. Furthermore, a motor driver board supporting SVPWM and FOC algorithm was designed and implemented, featuring wide voltage input, multiple output channels, and comprehensive protection functions. Experimental verification confirmed that the developed control system could generate ideal three-phase saddle wave and sinusoidal current waveforms, ensuring smooth motor operation. The system demonstrated excellent dyne pen test results on plasma-sprayed acrylic plates, effectively validating the feasibility of both structural optimization and control strategies. The research outcomes provide theoretical foundations and technical support for high-performance motor design in demanding applications such as plasma spraying.

  • Open Access

    Encapsulation Process and Dynamic Characterization of SiC Half-Bridge Power Module: Electro-Thermal Co-Design and Experimental Validation

    by Kaida Cai, Jing Xiao, Xingwei Su, Qiuhui Tang, Huayuan Deng

    Silicon carbide (SiC) half-bridge power modules are widely utilized in new energy power generation, electric vehicles, and industrial power supplies. To address the research gap in collaborative validation between electro-thermal coupling models and process reliability, this paper proposes a closed-loop methodology of “design-simulation-process-validation”. This approach integrates in-depth electro-thermal simulation (LTspice XVII/COMSOL Multiphysics 6.3) with micro/nano-packaging processes (sintering/bonding). Firstly, a multifunctional double-pulse test board was designed for the dynamic characterization of SiC devices. LTspice simulations revealed the switching characteristics under an 800 V operating condition. Subsequently, a thermal simulation model was constructed in COMSOL to quantify the module junction temperature gradient (25 °C → 80 °C). Key process parameters affecting reliability were then quantified, including conductive adhesive sintering (S820-F680, 39.3 W/m·K), high-temperature baking at 175 °C, and aluminum wire bonding (15 mil wire diameter and 500 mW ultrasonic power/500 g bonding force). Finally, a double-pulse dynamic test platform was established to capture switching transient characteristics. Experimental results demonstrated the following: (1) The packaged module successfully passed the 800 V high-voltage validation. Measured drain current (4.62 A) exhibited an error of <0.65% compared to the simulated value (4.65 A). (2) The simulated junction temperature (80 °C) was significantly below the safety threshold (175 °C). (3) Microscopic examination using a Leica IVesta 3 microscope (55× magnification) confirmed the absence of voids at the sintering and bonding interfaces. (4) Frequency-dependent dynamic characterization revealed a 6 nH parasitic inductance via Ansys Q3D 2025 R1 simulation, with experimental validation at 8.3 nH through double-pulse testing. Thermal evaluations up to 200 kHz indicated 109 °C peak temperature (below 175 °C datasheet limit) and low switching losses. This work provides a critical process benchmark for the micro/nano-manufacturing of high-density SiC modules.


  • Open Access

    Three-Level All-SiC High-Frequency High-Voltage Plasma Power Supply System

    by Kaida Cai, Jing Xiao, Zhe Yang, Ranghao Hu

    Plasma power supplies are extensively utilized in various manufacturing and medical industries. Addressing the challenges of high-voltage and high-temperature resistance in current plasma power supply systems under high-frequency conditions, this study proposes a novel design method for an all-SiC high-frequency high-voltage plasma power supply system based on a three-level topology. Firstly, the design encompasses a three-level high-frequency inverter main circuit, a three-level high-frequency control main circuit, and a high-frequency high-voltage transformer. Subsequently, a high-frequency high-voltage plasma power supply system, equipped with a rotary motor, was developed and experimentally validated. Finally, the system achieved a stable power output with a frequency of 25 kHz, an output voltage of 21.03 kV, and an output power of 13.42 kW. The experimental results demonstrate that the plasma power supply system exhibits stable output voltage and maintains an operating temperature under high-frequency and high-voltage conditions.