Abdulmumin Ahmed Shuaibu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Abdulmumin Ahmed Shuaibu has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Zhiping Zeng
School of Civil Engineering, Central South University, Changsha 410083, China
3 shared publications - Marui Han
Central South University
2 shared publications - Peicheng Li
School of Civil Engineering, Central South University, Changsha 410075, China
2 shared publications - Abdulfatai Adinoyi Murana1 shared publication
- Aliyu Usman
Department of Civil Engineering, Ahmadu Bello University, Zaria 810107, Nigeria
1 shared publication Bushrah Baba Abdulrahman
Department of Polymer and Textile Engineering, Ahmadu Bello University, Zaria, Nigeria
1 shared publication
Latest Publications
- Open Access
- 26 May 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (11) , 5351
Impact of Fastener Failure and Support Block Hanging Void on the Dynamic Characteristics of the Vehicle–Track Coupled System in Low Vibration Track in Curved Section of Heavy-Haul Railway
The wheel–rail impact effect is prominent in the low vibration track (LVT) in the curved sections of heavy-haul railways, where fastener failure and the support block hanging void are prone to occurring. To investigate the impact of these issues on the dynamic characteristics of the vehicle–track coupled system, this study establishes a coupled dynamics model of a heavy-haul train and LVT, taking into account the topological relationships of vehicle components, multipoint wheel–rail contact, and track irregularities. Comparative analyses are conducted to evaluate the effects of the location, quantity, and failure degree of fastener failure and support block hanging voids on running safety and stability. The results show that (1) compared to the normal condition, fastener failure and support block hanging voids lead to varying degrees of increases in response indicators, thereby intensifying the wheel–rail impact; (2) bilateral failure exhibits more pronounced dynamic responses than unilateral failure, and when the number of failed fasteners or hanging voids exceeds one, the maximum wheel load reduction rate increases significantly; (3) as the gap of the hanging void increases, the dynamic response also increases, and when the gap reaches approximately 3 mm, the support block can be considered fully suspended; and (4) comprehensive analysis indicates that fastener failure poses a greater threat to running safety than support block hanging voids and thus warrants greater attention in practical engineering applications. This study provides theoretical support for the maintenance and repair of heavy-haul railways.
- 26 May 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (11) , 5351
Open AccessImpact of Fastener Failure and Support Block Hanging Void on the Dynamic Characteristics of the Vehicle–Track Coupled System in Low Vibration Track in Curved Section of Heavy-Haul Railway
The wheel–rail impact effect is prominent in the low vibration track (LVT) in the curved sections of heavy-haul railways, where fastener failure and the support block hanging void are prone to occurring. To investigate the impact of these issues on the dynamic characteristics of the vehicle–track coupled system, this study establishes a coupled dynamics model of a heavy-haul train and LVT, taking into account the topological relationships of vehicle components, multipoint wheel–rail contact, and track irregularities. Comparative analyses are conducted to evaluate the effects of the location, quantity, and failure degree of fastener failure and support block hanging voids on running safety and stability. The results show that (1) compared to the normal condition, fastener failure and support block hanging voids lead to varying degrees of increases in response indicators, thereby intensifying the wheel–rail impact; (2) bilateral failure exhibits more pronounced dynamic responses than unilateral failure, and when the number of failed fasteners or hanging voids exceeds one, the maximum wheel load reduction rate increases significantly; (3) as the gap of the hanging void increases, the dynamic response also increases, and when the gap reaches approximately 3 mm, the support block can be considered fully suspended; and (4) comprehensive analysis indicates that fastener failure poses a greater threat to running safety than support block hanging voids and thus warrants greater attention in practical engineering applications. This study provides theoretical support for the maintenance and repair of heavy-haul railways.
- Open Access
- 1 January 2026
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2026 (1)
Synthesis and Characterization of Metakaolin‐Based Geopolymer for Industrial Application
Materials with enhanced properties are currently in high demand. Consequently, the ability to synthesize these materials efficiently, using low energy and without adverse environmental impact, has become a critical research priority. For this reason, geopolymers present an attractive prospect for researchers in material science and engineering. In this study, metakaolin (Kankara kaolin after dehydroxylization) was used as precursor for synthesis of geopolymer and its chemical composition was assessed by X‐ray fluorescence (XRF). The characterization of metakaolin and geopolymer was performed by Fourier transform infrared (FTIR) spectroscopy, X‐ray diffractometry (XRD), thermogravimetric analysis (TGA), and differential thermal analysis (DTA). The results from FTIR indicated a shift in frequency band confirming the occurrence of geopolymerization. XRD peaks verified the crystalline phase and amorphous phase of metakaolin and geopolymer consistent with FTIR. The TGA/DTA of geopolymer showed higher thermal resistivity, lower weight loss, lower rate of degradation, and volatization. In conclusion, a suitable geopolymer, with fitting chemical and thermal properties, was obtained, justifying its recommendation for industrial applications such as high temperature–resistant concrete, asphalt binder, and asphalt mixture modification.
- 1 January 2026
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2026 (1)
Open AccessSynthesis and Characterization of Metakaolin‐Based Geopolymer for Industrial Application
Materials with enhanced properties are currently in high demand. Consequently, the ability to synthesize these materials efficiently, using low energy and without adverse environmental impact, has become a critical research priority. For this reason, geopolymers present an attractive prospect for researchers in material science and engineering. In this study, metakaolin (Kankara kaolin after dehydroxylization) was used as precursor for synthesis of geopolymer and its chemical composition was assessed by X‐ray fluorescence (XRF). The characterization of metakaolin and geopolymer was performed by Fourier transform infrared (FTIR) spectroscopy, X‐ray diffractometry (XRD), thermogravimetric analysis (TGA), and differential thermal analysis (DTA). The results from FTIR indicated a shift in frequency band confirming the occurrence of geopolymerization. XRD peaks verified the crystalline phase and amorphous phase of metakaolin and geopolymer consistent with FTIR. The TGA/DTA of geopolymer showed higher thermal resistivity, lower weight loss, lower rate of degradation, and volatization. In conclusion, a suitable geopolymer, with fitting chemical and thermal properties, was obtained, justifying its recommendation for industrial applications such as high temperature–resistant concrete, asphalt binder, and asphalt mixture modification.
- Open Access
Study on the Mechanical Properties of Door-Shaped Rebar of a CRTS III Slab Track Under Temperature Load
CRTS III (China Railway Track System) slab track is a typical multi-layer composite structure. Door-shaped rebar is an important connecting component. Studying its service characteristics is crucial for disease prevention and control. To investigate the mechanical properties of door-shaped rebar under multi-factor coupling, a three-dimensional finite element model was developed and validated with full-scale tests. Then, considering the initial defects of self-compacting concrete (SCC), interlayer cracks and other damages, the mechanical properties of door-shaped rebar of a CRTS III slab track under temperature load were studied. The results show that under the action of an extreme temperature gradient, the maximum vertical displacement of the track slab occurs in the middle and corner positions of the slab with the positive temperature gradient, with displacement values of 0.87 mm and -0.99 mm respectively. Under positive and negative temperature gradients, the stress of the door-shaped rebar at the interface between the track slab and the SCC layer is 12.9 MPa and 16.5 MPa, respectively. When considering the conditions of the SCC slurry layer, the stress of the door-shaped rebar in the SCC layer under the action of a temperature gradient is generally in an increasing state. When there is a crack at the interface of the SCC layer, the stress of the door-shaped rebar unit in the crack area changes significantly, and the crack at the edge of track slab has the greatest impact on the stress of the door-shaped rebar under the positive temperature gradient, which is 157.9 MPa. The research results provide a theoretical basis for disease control.
Open AccessStudy on the Mechanical Properties of Door-Shaped Rebar of a CRTS III Slab Track Under Temperature Load
CRTS III (China Railway Track System) slab track is a typical multi-layer composite structure. Door-shaped rebar is an important connecting component. Studying its service characteristics is crucial for disease prevention and control. To investigate the mechanical properties of door-shaped rebar under multi-factor coupling, a three-dimensional finite element model was developed and validated with full-scale tests. Then, considering the initial defects of self-compacting concrete (SCC), interlayer cracks and other damages, the mechanical properties of door-shaped rebar of a CRTS III slab track under temperature load were studied. The results show that under the action of an extreme temperature gradient, the maximum vertical displacement of the track slab occurs in the middle and corner positions of the slab with the positive temperature gradient, with displacement values of 0.87 mm and -0.99 mm respectively. Under positive and negative temperature gradients, the stress of the door-shaped rebar at the interface between the track slab and the SCC layer is 12.9 MPa and 16.5 MPa, respectively. When considering the conditions of the SCC slurry layer, the stress of the door-shaped rebar in the SCC layer under the action of a temperature gradient is generally in an increasing state. When there is a crack at the interface of the SCC layer, the stress of the door-shaped rebar unit in the crack area changes significantly, and the crack at the edge of track slab has the greatest impact on the stress of the door-shaped rebar under the positive temperature gradient, which is 157.9 MPa. The research results provide a theoretical basis for disease control.
- Open Access
- 31 December 2024
- Published by Middle Technical University in Journal of Techniques
- Vol. 6 (4) , 1-18
A Novel Rubber Composite Sleeper-Deformation-Prediction Model Based on Response Surface Method (RSM) and Machine Learning (ML) Techniques
Rubber composite sleepers can experience significant temperature variations in service, causing temperature-induced deformation. Real-time monitoring of this deformation is crucial for operational safety and maintenance; however, it is costly, time-consuming, and requires substantial resources and personnel. Developing temperature-dependent predictive models offers a cost-effective and efficient alternative, providing accurate insights into sleeper behaviour under different conditions while saving time, labour, and materials. This study attempts to develop a novel deformation model of rubber composite sleepers using response surface methodology (RSM) and machine learning (ML) techniques. Platinum temperature (Pt) sensors, embedded at various points on a full-scale rubber composite sleeper model, were used to measure both the sleeper temperature field and ambient temperature in real-time at 30-minute intervals over the period of a year. Simultaneously, lateral deformation was recorded using linear variable differential transducer (LVDT) displacement sensors. The temperature data were filtered to remove noise and normalized based on the Log-Pearson Type III outlier detection method and Box-Cox transformation, respectively, before being used to develop temperature-dependent models for sleeper deformation. To ensure accurate ML predictions, the dataset was split into 70% for training and 30% for testing. Model performance was evaluated using the correlation coefficient (R2), mean square error (MSE), root means square error (RMSE), and mean absolute error (MAE). The analysis revealed that the sleeper’s body temperature closely follows the changing trend of the ambient environment. Also, like any polymer material, the rubber composite sleeper expands when it absorbs heat from sunlight and contracts as it cools when sunlight intensity decreases, potentially reversing much of the deformation. The K-nearest neighbour algorithm outperformed the RSM and other ML techniques with R2, MSE, RMSE, and MAE values of 0.999, 0.000258, 0.016, and 0.000896, respectively. The developed model can serve as an important reference for monitoring lateral deformation for safety and maintenance purposes.
- 31 December 2024
- Published by Middle Technical University in Journal of Techniques
- Vol. 6 (4) , 1-18
Open AccessA Novel Rubber Composite Sleeper-Deformation-Prediction Model Based on Response Surface Method (RSM) and Machine Learning (ML) Techniques
Rubber composite sleepers can experience significant temperature variations in service, causing temperature-induced deformation. Real-time monitoring of this deformation is crucial for operational safety and maintenance; however, it is costly, time-consuming, and requires substantial resources and personnel. Developing temperature-dependent predictive models offers a cost-effective and efficient alternative, providing accurate insights into sleeper behaviour under different conditions while saving time, labour, and materials. This study attempts to develop a novel deformation model of rubber composite sleepers using response surface methodology (RSM) and machine learning (ML) techniques. Platinum temperature (Pt) sensors, embedded at various points on a full-scale rubber composite sleeper model, were used to measure both the sleeper temperature field and ambient temperature in real-time at 30-minute intervals over the period of a year. Simultaneously, lateral deformation was recorded using linear variable differential transducer (LVDT) displacement sensors. The temperature data were filtered to remove noise and normalized based on the Log-Pearson Type III outlier detection method and Box-Cox transformation, respectively, before being used to develop temperature-dependent models for sleeper deformation. To ensure accurate ML predictions, the dataset was split into 70% for training and 30% for testing. Model performance was evaluated using the correlation coefficient (R2), mean square error (MSE), root means square error (RMSE), and mean absolute error (MAE). The analysis revealed that the sleeper’s body temperature closely follows the changing trend of the ambient environment. Also, like any polymer material, the rubber composite sleeper expands when it absorbs heat from sunlight and contracts as it cools when sunlight intensity decreases, potentially reversing much of the deformation. The K-nearest neighbour algorithm outperformed the RSM and other ML techniques with R2, MSE, RMSE, and MAE values of 0.999, 0.000258, 0.016, and 0.000896, respectively. The developed model can serve as an important reference for monitoring lateral deformation for safety and maintenance purposes.
- 27 February 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 235 (10) , 1268-1277
Longitudinal sliding resistance characteristics of the WJ-8 conventional resistance fastner
In this paper, the longitudinal resistance and displacement of the WJ-8 conventional resistance fastener under vertical and torque loadings were experimentally conducted and the relationship between longitudinal resistance and displacement was established. To validate the experimental results, numerical simulation using a finite-element model of the fastener was established to obtain the longitudinal resistance variation of the conventional-resistance. Results of the analysis show that both results of the experiment and simulation are in agreements. Furthermore, the skid resistance frictional coefficient of the fastener system under the vertical load was studied and its variation rule under both vertical and torque loads was obtained. The longitudinal sliding resistance of fasteners under different torques and/or vertical loads followed a linear trend. Under load and no-load conditions, the skid-resistance frictional coefficient of the fastener system varied significantly.
- 27 February 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 235 (10) , 1268-1277
Longitudinal sliding resistance characteristics of the WJ-8 conventional resistance fastner
In this paper, the longitudinal resistance and displacement of the WJ-8 conventional resistance fastener under vertical and torque loadings were experimentally conducted and the relationship between longitudinal resistance and displacement was established. To validate the experimental results, numerical simulation using a finite-element model of the fastener was established to obtain the longitudinal resistance variation of the conventional-resistance. Results of the analysis show that both results of the experiment and simulation are in agreements. Furthermore, the skid resistance frictional coefficient of the fastener system under the vertical load was studied and its variation rule under both vertical and torque loads was obtained. The longitudinal sliding resistance of fasteners under different torques and/or vertical loads followed a linear trend. Under load and no-load conditions, the skid-resistance frictional coefficient of the fastener system varied significantly.