Andrey Popov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Andrey Popov has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Kameliia Rashitova
Saint Petersburg State University, Saint Petersburg
4 shared publications - Svetlana N. Eliseeva
Saint Petersburg State University, Saint Petersburg
4 shared publications - Olga M. Osmolovskaya
Saint Petersburg State University, Saint Petersburg
3 shared publications - Aleksandr A. Kuchmizhak
Institute of Automation and Control Processes, Far Eastern Branch, Russian Academy of Sciences, Vladivostok, Russia
1 shared publication - Aleksandra Levshakova
Institute of Chemistry, St. Petersburg State University, St. Petersburg, Russia
1 shared publication - Alexey A. Kalinichev
St. Petersburg State University, St. Petersburg, Russia
1 shared publication
Latest Publications
- Open Access
- 25 June 2026
- Published by Ural Federal University in Chimica Techno Acta
- Vol. 13 (4) , 10502
Structural, electrochemical, and photocatalytic properties of Fe- and V-embedded MgAl layered double hydroxides
Mg-Al layered double hydroxides (LDHs) with Fe and V ions additively embedded in the layers were synthesized by co-precipitation and characterized by XRD, TEM, BET, XPS, ICP-AES, UV-Vis, and cyclic voltammetry. XRD confirmed a single hydrotalcite-like phase, while TEM revealed nanosheet morphology with thicknesses of ~ 3 nm. Cation addition caused a slight lattice contraction and significant changes in texture. V-embedded LDH exhibited the highest specific surface area (189 m2·g-1) and the widest pores (40 nm), whereas Fe-embedded LDH showed denser aggregation (127 m2·g-1) and the narrowest pores (9 nm). The fundamental optical band gap decreased from ~5.2 eV for pristine MgAl LDH to ~2.4 eV for Fe- and Fe, V-embedded samples and ~3.6 eV for V-embedded LDH, with additional sub-bandgap optical transitions enabling visible-light absorption. All modified samples showed similar decolorization efficiency (75–76%) under visible light, but TOC removal correlated with the optical properties: Fe- and Fe,V-embedded samples provided 48% total mineralization, compared to 35% for V-embedded LDH. These results highlight a correlation between the modified optical properties and the mineralization efficiency of the LDH-based photocatalysts, highlighting the importance of of rational selection of ions additively embedded in the layer for efficient visible-light photocatalysts.
- 25 June 2026
- Published by Ural Federal University in Chimica Techno Acta
- Vol. 13 (4) , 10502
Open AccessStructural, electrochemical, and photocatalytic properties of Fe- and V-embedded MgAl layered double hydroxides
Mg-Al layered double hydroxides (LDHs) with Fe and V ions additively embedded in the layers were synthesized by co-precipitation and characterized by XRD, TEM, BET, XPS, ICP-AES, UV-Vis, and cyclic voltammetry. XRD confirmed a single hydrotalcite-like phase, while TEM revealed nanosheet morphology with thicknesses of ~ 3 nm. Cation addition caused a slight lattice contraction and significant changes in texture. V-embedded LDH exhibited the highest specific surface area (189 m2·g-1) and the widest pores (40 nm), whereas Fe-embedded LDH showed denser aggregation (127 m2·g-1) and the narrowest pores (9 nm). The fundamental optical band gap decreased from ~5.2 eV for pristine MgAl LDH to ~2.4 eV for Fe- and Fe, V-embedded samples and ~3.6 eV for V-embedded LDH, with additional sub-bandgap optical transitions enabling visible-light absorption. All modified samples showed similar decolorization efficiency (75–76%) under visible light, but TOC removal correlated with the optical properties: Fe- and Fe,V-embedded samples provided 48% total mineralization, compared to 35% for V-embedded LDH. These results highlight a correlation between the modified optical properties and the mineralization efficiency of the LDH-based photocatalysts, highlighting the importance of of rational selection of ions additively embedded in the layer for efficient visible-light photocatalysts.
- Open Access
- 25 June 2026
- Published by Ural Federal University in Chimica Techno Acta
- Vol. 13 (4) , 10317
Cation-dependent phase formation and electrochemical behavior in Co- and Cu-modified layered vanadium oxide cathodes
Cation modification is proposed as a strategy for stabilizing layered mixed-valence vanadium oxide cathodes for aqueous zinc-ion batteries, yet the modifier is rarely considered as a competitor for the reducing agent that generates the layered phase. Here, Co2+- and Cu2+-containing vanadium oxides are prepared from V2O5 and oxalic acid via a single hydrothermal step. XRD, FTIR, XPS, ICP-AES, and electron microscopy reveal that the difference in redox activity between the two cations dictates the final product. Cobalt, which resists reduction and is partly reoxidized to Co3+ in situ, leaves most of the oxalate available for vanadium reduction, yielding a two-phase mixture of V10O24·12H2O and residual V2O5 with cobalt homogeneously dispersed throughout the matrix. In contrast, copper is readily reduced to Cu+, consuming the reductant and suppressing the layered phase, thereby producing crystalline V2O5 with a copper-enriched surface. The unmodified hydrate achieves 281 mAh·g-1 but retains only 26% after 500 cycles; the cobalt-modified sample peaks at 183.1 mAh·g-1 but fails within 140 cycles; whereas the copper-modified sample delivers 168.9 mAh·g-1 and retains 63%, offering the best stability but at lower capacity. We propose that the redox activity of the metal cation rather than ionic radius or the identity alone is a critical but often overlooked synthesis parameter that governs both structure and, consequently, functional properties in these cathode materials.
- 25 June 2026
- Published by Ural Federal University in Chimica Techno Acta
- Vol. 13 (4) , 10317
Open AccessCation-dependent phase formation and electrochemical behavior in Co- and Cu-modified layered vanadium oxide cathodes
Cation modification is proposed as a strategy for stabilizing layered mixed-valence vanadium oxide cathodes for aqueous zinc-ion batteries, yet the modifier is rarely considered as a competitor for the reducing agent that generates the layered phase. Here, Co2+- and Cu2+-containing vanadium oxides are prepared from V2O5 and oxalic acid via a single hydrothermal step. XRD, FTIR, XPS, ICP-AES, and electron microscopy reveal that the difference in redox activity between the two cations dictates the final product. Cobalt, which resists reduction and is partly reoxidized to Co3+ in situ, leaves most of the oxalate available for vanadium reduction, yielding a two-phase mixture of V10O24·12H2O and residual V2O5 with cobalt homogeneously dispersed throughout the matrix. In contrast, copper is readily reduced to Cu+, consuming the reductant and suppressing the layered phase, thereby producing crystalline V2O5 with a copper-enriched surface. The unmodified hydrate achieves 281 mAh·g-1 but retains only 26% after 500 cycles; the cobalt-modified sample peaks at 183.1 mAh·g-1 but fails within 140 cycles; whereas the copper-modified sample delivers 168.9 mAh·g-1 and retains 63%, offering the best stability but at lower capacity. We propose that the redox activity of the metal cation rather than ionic radius or the identity alone is a critical but often overlooked synthesis parameter that governs both structure and, consequently, functional properties in these cathode materials.
- Open Access
- 16 June 2026
- Published by Elsevier in SSRN Electronic Journal
Comparison of electrolyte type influence on the electrochemical performance of VO2/PPy composite as cathode for AZIBs
The influence of electrolyte composition (Zn(CF3SO3)2 vs. ZnSO4) on the electrochemical performance of VO2/PPy cathode for aqueous zinc-ion batteries was systematically investigated. The electrochemical performance of VO2/PPy composite in Zn(CF3SO3)2 is significantly superior compared to that in ZnSO4. After 250 cycles, the triflate electrolyte enabled a capacity retention of 60% (maximum 306.3 mAh∙g-1), while the sulfate system retained only 24% of its initial capacity. The results obtained demonstrate that the combination of VO2/PPy cathode with a zinc triflate electrolyte provides superior rate capability, cycling stability, and charge-transfer kinetics compared to the sulfate-based system.
- 16 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessComparison of electrolyte type influence on the electrochemical performance of VO2/PPy composite as cathode for AZIBs
The influence of electrolyte composition (Zn(CF3SO3)2 vs. ZnSO4) on the electrochemical performance of VO2/PPy cathode for aqueous zinc-ion batteries was systematically investigated. The electrochemical performance of VO2/PPy composite in Zn(CF3SO3)2 is significantly superior compared to that in ZnSO4. After 250 cycles, the triflate electrolyte enabled a capacity retention of 60% (maximum 306.3 mAh∙g-1), while the sulfate system retained only 24% of its initial capacity. The results obtained demonstrate that the combination of VO2/PPy cathode with a zinc triflate electrolyte provides superior rate capability, cycling stability, and charge-transfer kinetics compared to the sulfate-based system.
- 1 December 2024
- Published by Pleiades Publishing Ltd in Bulletin of the Russian Academy of Sciences: Physics
- Vol. 88 (S3) , S380-S384
Direct Laser Fabrication of Cobalt Patterns from Deep Eutectic Solvents
This study investigates the use of deep eutectic solvents (DES) in direct laser metallization (DLM) for the deposition of cobalt patterns on glass substrates. In order to extend the DLM technique to cobalt, a systematic study was conducted to synthesize a DES containing cobalt salts, specifically cobalt acetate and cobalt chloride, in different molar ratios. By optimizing the scanning speed and laser power, metallic structures with electrical conductivity were fabricated. Characterization techniques, including X-ray diffraction (XRD) and energy dispersive X-ray spectroscopy (EDX), confirmed the successful formation of cobalt patterns, while morphological studies revealed a well-developed structure without cracks or discontinuities. The results underscore the potential of DES in laser fabrication and demonstrate its versatility in facilitating the deposition of metal patterns.
- 1 December 2024
- Published by Pleiades Publishing Ltd in Bulletin of the Russian Academy of Sciences: Physics
- Vol. 88 (S3) , S380-S384
Direct Laser Fabrication of Cobalt Patterns from Deep Eutectic Solvents
This study investigates the use of deep eutectic solvents (DES) in direct laser metallization (DLM) for the deposition of cobalt patterns on glass substrates. In order to extend the DLM technique to cobalt, a systematic study was conducted to synthesize a DES containing cobalt salts, specifically cobalt acetate and cobalt chloride, in different molar ratios. By optimizing the scanning speed and laser power, metallic structures with electrical conductivity were fabricated. Characterization techniques, including X-ray diffraction (XRD) and energy dispersive X-ray spectroscopy (EDX), confirmed the successful formation of cobalt patterns, while morphological studies revealed a well-developed structure without cracks or discontinuities. The results underscore the potential of DES in laser fabrication and demonstrate its versatility in facilitating the deposition of metal patterns.