Dong Ho Shin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dong Ho Shin has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Su Woong Hyun
Department of Mechanical Engineering, Dongguk University-Seoul, 30 Pildong-ro 1-gil, Jung-gu, Seoul 04620, Republic of Korea
3 shared publications Hee Jun Jeong
2 shared publicationsSu Woong Hyun
2 shared publicationsGun Woo Kim
1 shared publicationHyun-Seok Kim
1 shared publicationJae Hyuk Kim
1 shared publication
Latest Publications
- 22 September 2026
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 232
Experimental and numerical investigation of coupled temperature and CO2 separation in a counter-flow vortex tube
- 22 September 2026
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 232
Experimental and numerical investigation of coupled temperature and CO2 separation in a counter-flow vortex tube
- Open Access
- 25 May 2026
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 83
Thermal performance and optimal temperature design of cascade LHTES systems with different configurations
- 25 May 2026
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 83
Open AccessThermal performance and optimal temperature design of cascade LHTES systems with different configurations
- Open Access
- 28 October 2025
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 76
Performance analysis of a solar wall integrated with latent heat storage and microencapsulated phase change material slurry
- 28 October 2025
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 76
Open AccessPerformance analysis of a solar wall integrated with latent heat storage and microencapsulated phase change material slurry
- Open Access
Hybrid PCM–Liquid Cooling System with Optimized Channel Design for Enhanced Thermal Management of Lithium–Ion Batteries
The increasing demand for high-efficiency cooling technologies necessitates improved methods to prevent degradation and ensure reliable operation of lithium–ion batteries. Conventional PCM (phase change material)-based cooling systems are limited by low thermal conductivity and uneven phase change processes, which lead to non-uniform thermal distribution and diminished performance. In response to these challenges, this study introduces a hybrid thermal management system that combines an indirect liquid-cooling structure with multiple cooling channel configurations within a PCM-based battery pack. Numerical simulations were conducted to systematically assess the thermal performance of the proposed design. Experimental validation with various cooling media showed that PCM achieved the greatest reduction in temperature (47%) and the longest isothermal duration (56 min) under air-cooled conditions, surpassing thermally conductive adhesive (40%) and silicone oil (26%) for temperature decrease. Vertical temperature differentials were effectively reduced, staying below only 2 °C for silicone oil and reaching a maximum of 4 °C for PCM. Phase change evaluation indicated that after 30 min of operation, only 37% of the PCM volume had melted, highlighting localized constraints in heat transfer. Comparative analysis among four liquid-cooling channel arrangements (A–D) and a standalone PCM system demonstrated that configuration D exhibited the highest cooling capability, lowering the battery surface temperature by as much as 9 °C (17.8%). Flow rate analysis determined that increases above 0.2 L/min resulted in only modest thermal improvements (<1 °C), with 0.108 L/min identified as the most efficient rate. Relative to PCM-only designs, the advanced hybrid cooling system achieved significantly enhanced thermal regulation and temperature uniformity, underscoring its promise as a superior solution for lithium–ion battery thermal management.
Open AccessHybrid PCM–Liquid Cooling System with Optimized Channel Design for Enhanced Thermal Management of Lithium–Ion Batteries
The increasing demand for high-efficiency cooling technologies necessitates improved methods to prevent degradation and ensure reliable operation of lithium–ion batteries. Conventional PCM (phase change material)-based cooling systems are limited by low thermal conductivity and uneven phase change processes, which lead to non-uniform thermal distribution and diminished performance. In response to these challenges, this study introduces a hybrid thermal management system that combines an indirect liquid-cooling structure with multiple cooling channel configurations within a PCM-based battery pack. Numerical simulations were conducted to systematically assess the thermal performance of the proposed design. Experimental validation with various cooling media showed that PCM achieved the greatest reduction in temperature (47%) and the longest isothermal duration (56 min) under air-cooled conditions, surpassing thermally conductive adhesive (40%) and silicone oil (26%) for temperature decrease. Vertical temperature differentials were effectively reduced, staying below only 2 °C for silicone oil and reaching a maximum of 4 °C for PCM. Phase change evaluation indicated that after 30 min of operation, only 37% of the PCM volume had melted, highlighting localized constraints in heat transfer. Comparative analysis among four liquid-cooling channel arrangements (A–D) and a standalone PCM system demonstrated that configuration D exhibited the highest cooling capability, lowering the battery surface temperature by as much as 9 °C (17.8%). Flow rate analysis determined that increases above 0.2 L/min resulted in only modest thermal improvements (<1 °C), with 0.108 L/min identified as the most efficient rate. Relative to PCM-only designs, the advanced hybrid cooling system achieved significantly enhanced thermal regulation and temperature uniformity, underscoring its promise as a superior solution for lithium–ion battery thermal management.
- 1 March 2025
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 39 (3) , 1477-1486
Thermal fluidic characteristics of microencapsulated PCM slurry (MPCS) in battery immersion cooling
- 1 March 2025
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 39 (3) , 1477-1486
Thermal fluidic characteristics of microencapsulated PCM slurry (MPCS) in battery immersion cooling