Igor Augusto Dias Gonzaga
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Igor Augusto Dias Gonzaga has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Almir Silva Neto
Department of Metallurgy and Chemistry, Centro Federal de Educação Tecnológica de Minas Gerais, R. 19 de Novembro, 121, Centro Norte, Timóteo 35180-008, MG, Brazil
1 shared publication - Erriston Campos Amaral
Department of Metallurgy and Chemistry, Centro Federal de Educação Tecnológica de Minas Gerais, R. 19 de Novembro, 121, Centro Norte, Timóteo 35180-008, MG, Brazil
1 shared publication - Karina Aparecida Martins Barcelos Gonçalves
Department of Metallurgy and Chemistry, Centro Federal de Educação Tecnológica de Minas Gerais, R. 19 de Novembro, 121, Centro Norte, Timóteo 35180-008, MG, Brazil
1 shared publication - Paulo César de Matos Rodrigues
Graduate Program in Mechanical Engineering, Universidade Federal de Minas Gerais, Av. Antônio Carlos, 6627, Pampulha, Belo Horizonte 31270-901, MG, Brazil
1 shared publication - Thales Harvey Crisóstomo Barros
Department of Metallurgy and Chemistry, Centro Federal de Educação Tecnológica de Minas Gerais, R. 19 de Novembro, 121, Centro Norte, Timóteo 35180-008, MG, Brazil
1 shared publication - Valmir Dias Luiz
Postgraduate Program in Materials Engineering Centro Federal de Educação Tecnológica de Minas Gerais Timóteo Brazil
1 shared publication
Latest Publications
- 1 January 2024
- Published by Rzeszow University of Technology in Advances in Mechanical and Materials Engineering
- Vol. 42 (1) , 59-69
Influence of Multi-Pass Forming on the Tribological Performance of AISI 430 Steel Sheet in Deep Drawing Process
In this paper, the effect of sheet pre-deformation on the change of the surface roughness parameters and friction coefficient value is investigated. For this purpose, strips of AISI 430 ferritic stainless steel with deep drawing quality (DDQ), measuring 0.8 × 25 × 500 mm, were pre-deformed using a uniaxial tensile test for five different true strain values. The correlation between the surface roughness parameters and hardness with the frictional conditions of the tested strips was investigated in the bending under tension test. The results revealed that the friction coefficient determined for all pre-deformed strips increased as the level of true strain also increased. An increase in the plastic deformation of sheets under the uniaxial tensile stress state causes a nearly linear increase in the value of basic amplitude parameters of surface roughness, however, the hardness tended to present a constant increase for deformations close to uniform elongation. Furthermore, scratches and severe wear occurred on the surface of the strips and intensified with increasing roughness.
- 1 January 2024
- Published by Rzeszow University of Technology in Advances in Mechanical and Materials Engineering
- Vol. 42 (1) , 59-69
Influence of Multi-Pass Forming on the Tribological Performance of AISI 430 Steel Sheet in Deep Drawing Process
In this paper, the effect of sheet pre-deformation on the change of the surface roughness parameters and friction coefficient value is investigated. For this purpose, strips of AISI 430 ferritic stainless steel with deep drawing quality (DDQ), measuring 0.8 × 25 × 500 mm, were pre-deformed using a uniaxial tensile test for five different true strain values. The correlation between the surface roughness parameters and hardness with the frictional conditions of the tested strips was investigated in the bending under tension test. The results revealed that the friction coefficient determined for all pre-deformed strips increased as the level of true strain also increased. An increase in the plastic deformation of sheets under the uniaxial tensile stress state causes a nearly linear increase in the value of basic amplitude parameters of surface roughness, however, the hardness tended to present a constant increase for deformations close to uniform elongation. Furthermore, scratches and severe wear occurred on the surface of the strips and intensified with increasing roughness.