Guoqiang Wei
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Guoqiang Wei has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Libin Yang
Metallurgical Technology Institute, Central Iron and Steel Research Institute Co., Ltd., Beijing 100081, China
2 shared publications - Bowen Peng
Metallurgical Technology Institute, Central Iron and Steel Research Institute Co., Ltd., Beijing 100081, China
1 shared publication - Chengyi Wang
School of Metallurgy, Northeastern University, Shenyang 110004, China
1 shared publication - Guangheng Ji
Metallurgical Department, Central Iron and Steel Research Institute, Beijing 100081, China
1 shared publication - Jiagui Shi
Metallurgical Technology Institute, Central Iron and Steel Research Institute Co., Ltd., Beijing 100081, China
1 shared publication - Wei Wu
Metallurgical Department, Central Iron and Steel Research Institute, Beijing 100081, China
1 shared publication
Latest Publications
- Open Access
Thermal Simulation Experiments on Smelting Characteristics and Dephosphorization in Converter with High Scrap Ratio
Smelting with a high scrap ratio in converters holds significant importance for carbon reduction and emission reduction in the iron and steel industry. Under high scrap ratio conditions, the kinetic and thermodynamic conditions of the molten bath change significantly, leading to considerable differences in the elemental reactions and slag formation patterns during the smelting process. To investigate the reaction characteristics and dephosphorization behavior of the molten bath under different scrap ratios, this study conducted thermal simulation experiments of converter smelting with four scrap ratios (20%, 30%, 40%, and 50%) using a 500 kg induction furnace. Scrap preheating and supplemental heating agents were applied as needed. Slag petrographic analysis was carried out using SEM and EDS. The experimental results indicate that with scrap ratios of 20% and 30%, the carbon–oxygen reaction and slag formation efficiency are relatively high. The dephosphorization rate in the early stage of smelting can exceed 50%, and phosphorus is effectively enriched in the CaO–SiO2 matrix phase, with the highest phosphorus distribution ratio observed at a 30% scrap ratio. In contrast, with scrap ratios of 40% and 50%, the carbon–oxygen reaction is slower, and the dephosphorization rate in the early smelting stage is less than 10%. In the 40% scrap ratio experiment, phosphorus began to accumulate significantly in the dicalcium silicate phase during the mid-smelting stage as the basicity increased. At a 50% scrap ratio, the silicate matrix remained the dominant phase throughout all smelting stages, and no distinct phosphorus-rich phase was formed.
Open AccessThermal Simulation Experiments on Smelting Characteristics and Dephosphorization in Converter with High Scrap Ratio
Smelting with a high scrap ratio in converters holds significant importance for carbon reduction and emission reduction in the iron and steel industry. Under high scrap ratio conditions, the kinetic and thermodynamic conditions of the molten bath change significantly, leading to considerable differences in the elemental reactions and slag formation patterns during the smelting process. To investigate the reaction characteristics and dephosphorization behavior of the molten bath under different scrap ratios, this study conducted thermal simulation experiments of converter smelting with four scrap ratios (20%, 30%, 40%, and 50%) using a 500 kg induction furnace. Scrap preheating and supplemental heating agents were applied as needed. Slag petrographic analysis was carried out using SEM and EDS. The experimental results indicate that with scrap ratios of 20% and 30%, the carbon–oxygen reaction and slag formation efficiency are relatively high. The dephosphorization rate in the early stage of smelting can exceed 50%, and phosphorus is effectively enriched in the CaO–SiO2 matrix phase, with the highest phosphorus distribution ratio observed at a 30% scrap ratio. In contrast, with scrap ratios of 40% and 50%, the carbon–oxygen reaction is slower, and the dephosphorization rate in the early smelting stage is less than 10%. In the 40% scrap ratio experiment, phosphorus began to accumulate significantly in the dicalcium silicate phase during the mid-smelting stage as the basicity increased. At a 50% scrap ratio, the silicate matrix remained the dominant phase throughout all smelting stages, and no distinct phosphorus-rich phase was formed.
- Open Access
Analysis of Typical Inclusion Evolution and Formation Mechanism in the Smelting Process of W350 Non-Oriented Silicon Steel
The production of silicon steel involves complex metallurgical processes, where the kind, composition, size, and quantity of the inclusions generated affect the silicon steel properties. This article is based on the smelting process for W350 non-oriented silicon steel produced by a certain factory. By systematically sampling, at key nodes of the converter–RH refining–tundish smelting process, the change in cleanliness of molten steel in the whole smelting process, the evolution of typical inclusions, and the transformation rules for the precipitated phase were analyzed by means of SEM-EDS, ASPEX, and Thermal-Calc. The results indicate that the total oxygen mass fraction in the steel decreases by more than 95% after deoxidation alloying, and the average oxygen mass fraction in the RH outbound steel is 0.0012%. While the nitrogen mass fraction shows a rising trend as a whole, the average nitrogen mass fraction in the tundish steel reaches approximately 0.0014%. Before RH refining, large Al2O3–CaO–SiO2 and Al2O3–CaO–SiO2–MgO composite inclusions are the main inclusions. MnO and Al2O3–SiO2–MnO inclusions are the main inclusions after RH inlet and RH decarburization. After RH deoxidation with aluminum, the inclusions were almost entirely transformed into Al2O3 inclusions. After RH alloying, with the content of Si and Mn increased, the inclusions transformed into Al2O3–SiO2–MnO inclusions. The number of inclusions from RH desulfurization to the RH outbound stage declined significantly, and composite inclusions containing CaS and precipitates such as AlN and MnS began to appear. The inclusions’ main types were Al2O3–MgO–CaS, AlN–MnS, AlN, and Al2O3–MgO. The inclusions inside the tundish were the same, but the numbers were slightly increased due to the secondary oxidation of molten steel. More than 80% of the oxide inclusions in the whole process were between 1 μm and 5 μm in size. The average size and the number of inclusions per unit area reached 5.45 μm and 63.1 per mm2, respectively, after RH deoxidation, and respectively decreased to 3.71 μm and 1.9 per mm2 during the RH outbound stage, but both increased slightly in the tundish. Thermodynamic calculation shows that Al2O3–MgO inclusions are formed when w([Mg]) > 0.0033% in molten steel at 1873 K. Under the actual temperature of 1828K and w([Al]s) = 0.6515%, the range of w([Mg]) corresponding to the stable existence of Al2O3–MgO is between 0.0053% and 0.1676%. The liquidus temperature of W350 non-oriented silicon steel is 1489 °C. MnS and AlN inclusions are precipitated successively with the solidification of molten steel, and the precipitation temperatures are 1460.7 °C and 1422.2 °C, respectively. As the temperature decreases, the sequence of inclusion precipitation calculated in liquid was as follows: Al2O3–CaO → 2Al2O3–CaO + MnS → 6Al2O3–CaO → Al2O3 + AlN + MnS + CaS.
Open AccessAnalysis of Typical Inclusion Evolution and Formation Mechanism in the Smelting Process of W350 Non-Oriented Silicon Steel
The production of silicon steel involves complex metallurgical processes, where the kind, composition, size, and quantity of the inclusions generated affect the silicon steel properties. This article is based on the smelting process for W350 non-oriented silicon steel produced by a certain factory. By systematically sampling, at key nodes of the converter–RH refining–tundish smelting process, the change in cleanliness of molten steel in the whole smelting process, the evolution of typical inclusions, and the transformation rules for the precipitated phase were analyzed by means of SEM-EDS, ASPEX, and Thermal-Calc. The results indicate that the total oxygen mass fraction in the steel decreases by more than 95% after deoxidation alloying, and the average oxygen mass fraction in the RH outbound steel is 0.0012%. While the nitrogen mass fraction shows a rising trend as a whole, the average nitrogen mass fraction in the tundish steel reaches approximately 0.0014%. Before RH refining, large Al2O3–CaO–SiO2 and Al2O3–CaO–SiO2–MgO composite inclusions are the main inclusions. MnO and Al2O3–SiO2–MnO inclusions are the main inclusions after RH inlet and RH decarburization. After RH deoxidation with aluminum, the inclusions were almost entirely transformed into Al2O3 inclusions. After RH alloying, with the content of Si and Mn increased, the inclusions transformed into Al2O3–SiO2–MnO inclusions. The number of inclusions from RH desulfurization to the RH outbound stage declined significantly, and composite inclusions containing CaS and precipitates such as AlN and MnS began to appear. The inclusions’ main types were Al2O3–MgO–CaS, AlN–MnS, AlN, and Al2O3–MgO. The inclusions inside the tundish were the same, but the numbers were slightly increased due to the secondary oxidation of molten steel. More than 80% of the oxide inclusions in the whole process were between 1 μm and 5 μm in size. The average size and the number of inclusions per unit area reached 5.45 μm and 63.1 per mm2, respectively, after RH deoxidation, and respectively decreased to 3.71 μm and 1.9 per mm2 during the RH outbound stage, but both increased slightly in the tundish. Thermodynamic calculation shows that Al2O3–MgO inclusions are formed when w([Mg]) > 0.0033% in molten steel at 1873 K. Under the actual temperature of 1828K and w([Al]s) = 0.6515%, the range of w([Mg]) corresponding to the stable existence of Al2O3–MgO is between 0.0053% and 0.1676%. The liquidus temperature of W350 non-oriented silicon steel is 1489 °C. MnS and AlN inclusions are precipitated successively with the solidification of molten steel, and the precipitation temperatures are 1460.7 °C and 1422.2 °C, respectively. As the temperature decreases, the sequence of inclusion precipitation calculated in liquid was as follows: Al2O3–CaO → 2Al2O3–CaO + MnS → 6Al2O3–CaO → Al2O3 + AlN + MnS + CaS.