Shufan Xu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Shufan Xu has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Kiichi Niitsu
Graduate School of Informatics, Kyoto University, Kyoto, Japan
5 shared publications - Kunyang Liu
Kyoto University
5 shared publications - Hirofumi Shinohara
Kyoto University
3 shared publications - Ruilin Zhang
Department of Communications and Computer Engineering, Kyoto University, Kyoto, Japan
3 shared publications - Hiroaki Kitaike
Graduate School of Informatics, Kyoto University, Kyoto, Japan
2 shared publications Hironori Tagawa
Graduate School of Informatics, Kyoto University, Kyoto, Japan
2 shared publications
Latest Publications
- Open Access
- 3 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. PP (00189200) , 1-14
A Physically Unclonable Function With Less Than 4.16E–7 BER Featuring Secure In-Cell HCI Burn-In and nMOS-Dominant PUF Data Generation
Physically unclonable functions (PUFs) are a fundamental component of hardware security, enabling secure and low-cost on-chip secret key generation. However, achieving near-zero bit error rates (BERs) across wide supply voltage and temperature (VT) variations often requires access to secret PUF data during stabilization, which poses security risks. This work presents an eight-transistor (8T) SRAM-based PUF that employs a secure in-cell hot-carrier injection (HCI) burn-in technique to stabilize the PUF without requiring access to PUF data and without incurring redundancy, bitcell loss, or on-chip mask data storage. An nMOS-dominant PUF data generation technique is introduced to enhance HCI effectiveness and suppress long-term aging effects, achieving near-zero BER across VT corners even after long-term operation. Fabricated in a standard 130-nm CMOS process, the proposed design achieves a BER of less than 4.16E–7 across a temperature range from –20 °C to 120 °C and a supply voltage range of 1.17–1.43 V. Long-term reliability is validated through a 320-h accelerated aging test. In addition, the design attains a compact bitcell area of 434 F2 and low energy consumption of 8.52 fJ/bit.
- 3 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. PP (00189200) , 1-14
Open AccessA Physically Unclonable Function With Less Than 4.16E–7 BER Featuring Secure In-Cell HCI Burn-In and nMOS-Dominant PUF Data Generation
Physically unclonable functions (PUFs) are a fundamental component of hardware security, enabling secure and low-cost on-chip secret key generation. However, achieving near-zero bit error rates (BERs) across wide supply voltage and temperature (VT) variations often requires access to secret PUF data during stabilization, which poses security risks. This work presents an eight-transistor (8T) SRAM-based PUF that employs a secure in-cell hot-carrier injection (HCI) burn-in technique to stabilize the PUF without requiring access to PUF data and without incurring redundancy, bitcell loss, or on-chip mask data storage. An nMOS-dominant PUF data generation technique is introduced to enhance HCI effectiveness and suppress long-term aging effects, achieving near-zero BER across VT corners even after long-term operation. Fabricated in a standard 130-nm CMOS process, the proposed design achieves a BER of less than 4.16E–7 across a temperature range from –20 °C to 120 °C and a supply voltage range of 1.17–1.43 V. Long-term reliability is validated through a 320-h accelerated aging test. In addition, the design attains a compact bitcell area of 434 F2 and low energy consumption of 8.52 fJ/bit.
- Open Access
- 21 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 72 (11) , 1575-1579
Design and Experimental Verification of 0.9-2.6pW 0.1-0.25V 22nm 2-Bit Supply-to-Digital Converter Using Always-Activated Supply-Controlled Oscillator and Supply-Dependent-Activation Buffers for Bio-Fuel-Cell-Powered-and-Sensed Time-Stamped Bio-Recording
The sensor with low power consumption, small area and low operational voltage is particularly important for power-limited, area-limited sensors such as in-body sensors. This paper presents a low power supply-to-digital converter (SDC) for bio-recording system where bio-fuel-cell provides both power and sensing data. It is achieved by a supply-controlled oscillator, supply-dependent activation buffers (SDAB) with different V-thresholds, and an encoder. A prototype chip was fabricated using 22nm CMOS ULL and exhibits its feasibility with a power of 0.9-2.6 pW under 0.1-0.25 V. The chip size reached 0.00028 mm2. Design methodologies for minimizing power consumption and controlling buffer V-threshold of SDAB, which is the keys in this work, are introduced.
- 21 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 72 (11) , 1575-1579
Open AccessDesign and Experimental Verification of 0.9-2.6pW 0.1-0.25V 22nm 2-Bit Supply-to-Digital Converter Using Always-Activated Supply-Controlled Oscillator and Supply-Dependent-Activation Buffers for Bio-Fuel-Cell-Powered-and-Sensed Time-Stamped Bio-Recording
The sensor with low power consumption, small area and low operational voltage is particularly important for power-limited, area-limited sensors such as in-body sensors. This paper presents a low power supply-to-digital converter (SDC) for bio-recording system where bio-fuel-cell provides both power and sensing data. It is achieved by a supply-controlled oscillator, supply-dependent activation buffers (SDAB) with different V-thresholds, and an encoder. A prototype chip was fabricated using 22nm CMOS ULL and exhibits its feasibility with a power of 0.9-2.6 pW under 0.1-0.25 V. The chip size reached 0.00028 mm2. Design methodologies for minimizing power consumption and controlling buffer V-threshold of SDAB, which is the keys in this work, are introduced.
- Open Access
- 8 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 33 (10) , 2668-2679
A 65-nm CMOS Downconverter-Less Clock Generator Architecture Using Voltage Stacking of Oscillator and Frequency Dividers for Scaling-Friendly IoTs
The demand for high energy efficiency in IoT devices continues to increase, necessitating the development of low energy consumption techniques to enhance the computation performance of these devices. In this study, we present a CMOS clock generator that operates at high operating voltage, achieves low frequency, and exhibits low power (LP) consumption, thus obviating the need for scaling-unfriendly step-down converters. The avoidance of step-down converters, which require passive components in their design, facilitates the development of scaling-friendly IoTs. The architecture of the prototype chip is composed of a voltage stacking and charge recycling design, which is achieved by the implementation of stacked oscillator and multiple frequency dividers in a configuration. The fabrication of the prototype chip is conducted using a 65-nm CMOS process. This work presents two configurations that are based on the concept of voltage stacking. The first configuration prioritizes LP consumption, yielding a clock generation of 2.09 Hz with a power of 0.22 nW at a voltage supply of 1.2 V and an operating range of 1.2–2.2 V. Notably, this configuration represents the lowest power achieved at a foundry-recommended nominal voltage in a sub-10-Hz clock generator. Another configuration is oriented toward generating low-frequency output signals, and the test chip attains an output frequency of 0.079 Hz and a supply voltage range of 0.88–1.3 V. The proposed architecture exhibits potential benefits in advanced technology nodes, particularly in the context of technology scaling.
- 8 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 33 (10) , 2668-2679
Open AccessA 65-nm CMOS Downconverter-Less Clock Generator Architecture Using Voltage Stacking of Oscillator and Frequency Dividers for Scaling-Friendly IoTs
The demand for high energy efficiency in IoT devices continues to increase, necessitating the development of low energy consumption techniques to enhance the computation performance of these devices. In this study, we present a CMOS clock generator that operates at high operating voltage, achieves low frequency, and exhibits low power (LP) consumption, thus obviating the need for scaling-unfriendly step-down converters. The avoidance of step-down converters, which require passive components in their design, facilitates the development of scaling-friendly IoTs. The architecture of the prototype chip is composed of a voltage stacking and charge recycling design, which is achieved by the implementation of stacked oscillator and multiple frequency dividers in a configuration. The fabrication of the prototype chip is conducted using a 65-nm CMOS process. This work presents two configurations that are based on the concept of voltage stacking. The first configuration prioritizes LP consumption, yielding a clock generation of 2.09 Hz with a power of 0.22 nW at a voltage supply of 1.2 V and an operating range of 1.2–2.2 V. Notably, this configuration represents the lowest power achieved at a foundry-recommended nominal voltage in a sub-10-Hz clock generator. Another configuration is oriented toward generating low-frequency output signals, and the test chip attains an output frequency of 0.079 Hz and a supply voltage range of 0.88–1.3 V. The proposed architecture exhibits potential benefits in advanced technology nodes, particularly in the context of technology scaling.
- Open Access
- 29 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 25 (3) , 481-491
Statistical Model and Transistor Size Effect of Hot Carrier Injection for Stability Reinforced SRAM Physically Unclonable Function
Hot carrier injection (HCI) has been strategically leveraged to enhance the stability of SRAM physically unclonable functions (PUFs). Since the effects of HCI are not constant, exhibiting cell-to-cell variability, a comprehensive distribution model is essential to harness HCI effectively. This article presents a statistical distribution model of mismatch after HCI burn-in and examines the impact of transistor size of PUF on the distribution shape, yielding enhanced stability and shorter HCI burn-in time. The proposed mismatch model after HCI burn-in integrates the native distribution with a Poisson distribution for number of captured electrons and a Gamma distribution for the effect of captured electrons. Model calculations based on size effects reveal that over three times reduction in HCI burn-in duration by enhancing the size to quadruple times: a 15-min for quadruple-size transistor SRAM PUF compared to 46-min for single-size PUF. The model is confirmed by the real chip measurement. The PUFs with several sized transistors are fabricated in a 130-nm standard CMOS process. Experimental results show that quadruple-size transistor SRAM PUF reaches 1.82E09 unstable cell ratio after 18-min HCI burn-in, which align with the model based expectation. Furthermore, robust stability is exhibited even the worst VT corner (0.6V / 40), demonstrating zero bit error (BER7.81E08).
- 29 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 25 (3) , 481-491
Open AccessStatistical Model and Transistor Size Effect of Hot Carrier Injection for Stability Reinforced SRAM Physically Unclonable Function
Hot carrier injection (HCI) has been strategically leveraged to enhance the stability of SRAM physically unclonable functions (PUFs). Since the effects of HCI are not constant, exhibiting cell-to-cell variability, a comprehensive distribution model is essential to harness HCI effectively. This article presents a statistical distribution model of mismatch after HCI burn-in and examines the impact of transistor size of PUF on the distribution shape, yielding enhanced stability and shorter HCI burn-in time. The proposed mismatch model after HCI burn-in integrates the native distribution with a Poisson distribution for number of captured electrons and a Gamma distribution for the effect of captured electrons. Model calculations based on size effects reveal that over three times reduction in HCI burn-in duration by enhancing the size to quadruple times: a 15-min for quadruple-size transistor SRAM PUF compared to 46-min for single-size PUF. The model is confirmed by the real chip measurement. The PUFs with several sized transistors are fabricated in a 130-nm standard CMOS process. Experimental results show that quadruple-size transistor SRAM PUF reaches 1.82E09 unstable cell ratio after 18-min HCI burn-in, which align with the model based expectation. Furthermore, robust stability is exhibited even the worst VT corner (0.6V / 40), demonstrating zero bit error (BER7.81E08).
- Open Access
- 20 January 2025
- Published by Association for Computing Machinery (ACM)
- p. 364-367
Design of 0.9-2.6pW 0.1-0.25V 22nm 2-bit Supply-to-Digital Converter Using Always-Activated Supply-Controlled Oscillator and Supply-Dependent-Activation Buffers for Bio-Fuel-Cell-Powered-and-Sensed Time-Stamped Bio-Recording
This paper presents a low-power supply-to-digital converter (SDC) for bio-recording system where bio-fuel-cell provides both power and sensing data. It is achieved by a supply-controlled oscillator, supply-dependent activation buffers (SDAB) with different V-thresholds, and an encoder. A 22-nm prototype chip exhibits its feasibility with a power of 0.9-2.6 pW under 0.1-0.25 V. Design methodology for minimizing power consumption and techniques of controlling buffer V-threshold are also introduced.
- 20 January 2025
- Published by Association for Computing Machinery (ACM)
- p. 364-367
Open AccessDesign of 0.9-2.6pW 0.1-0.25V 22nm 2-bit Supply-to-Digital Converter Using Always-Activated Supply-Controlled Oscillator and Supply-Dependent-Activation Buffers for Bio-Fuel-Cell-Powered-and-Sensed Time-Stamped Bio-Recording
This paper presents a low-power supply-to-digital converter (SDC) for bio-recording system where bio-fuel-cell provides both power and sensing data. It is achieved by a supply-controlled oscillator, supply-dependent activation buffers (SDAB) with different V-thresholds, and an encoder. A 22-nm prototype chip exhibits its feasibility with a power of 0.9-2.6 pW under 0.1-0.25 V. Design methodology for minimizing power consumption and techniques of controlling buffer V-threshold are also introduced.