Hyunjae Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Hyunjae Kim has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Byeng D. Youn
Department of Mechanical Engineering, Seoul National University, Seoul 08826, South Korea and Institute of Advanced Machines and Design, Seoul National University, Seoul 08826, South Korea and OnePredict Inc., Seoul 08826, South Korea
1 shared publication- Byunghun Lee
Hanyang University
1 shared publication - Changbyung Park
KAIST, Daejeon, Republic of Korea
1 shared publication - Chun Taek Rim
Department of Electrical Engineering and Computer Science, Gwangju Institute of Science and Technology, Gwangju, South Korea
1 shared publication Gil-Young Oh
1 shared publicationGwi-Hwan Park
1 shared publication
Latest Publications
- 31 December 2021
- Published by The Society for Environmental Technology in Korea in Journal of the Korean Society for Environmental Technology
- Vol. 22 (6) , 461-470
Investigation on the Cause of Odor in Yeosu National Industrial Complex and Its Surrounding Area
The purpose of this study is to understand the current status and cause of the distribution of odor substances in the Yeosu National Industrial Complex and its surrounding areas. Samples were analyzed by collecting 90 samples at dawn, daytime and night from a total of 15 points, 9 points in the management area, 2 points in the boundary area, and 4 points in the affected area. The analysis items include 5 meteorological factors, complex odor, 22 types of the designated odors and other Volatile Organic Compounds (VOCs). At the MA3 (Fig. 1) point in the management area, the strict emission allowance standard for complex odors was exceeded three times, Ammonia, two types of sulfur compounds, two types of aldehydes, and six types of VOCs were detected, but they were within the standard. As a result of by calculating the odor contribution, the contribution of 74.9 % or more was found at the point where butyraldehyde was detected. Therefore, in order to prevent odors at the Yeosu Industrial Complex, measures to reduce aldehydes with high odor contribution should be prioritized, and it is necessary to simultaneously investigate through real-time harmful atmospheric measurement vehicles. Based on the contents presented in this study, if the system and policies reflecting the results of the odor occurrence survey of Yeosu National Industrial Complex and surrounding areas are supplemented, the odor environment of Yeosu National Industrial Complex will be sufficiently improved.
- 31 December 2021
- Published by The Society for Environmental Technology in Korea in Journal of the Korean Society for Environmental Technology
- Vol. 22 (6) , 461-470
Investigation on the Cause of Odor in Yeosu National Industrial Complex and Its Surrounding Area
The purpose of this study is to understand the current status and cause of the distribution of odor substances in the Yeosu National Industrial Complex and its surrounding areas. Samples were analyzed by collecting 90 samples at dawn, daytime and night from a total of 15 points, 9 points in the management area, 2 points in the boundary area, and 4 points in the affected area. The analysis items include 5 meteorological factors, complex odor, 22 types of the designated odors and other Volatile Organic Compounds (VOCs). At the MA3 (Fig. 1) point in the management area, the strict emission allowance standard for complex odors was exceeded three times, Ammonia, two types of sulfur compounds, two types of aldehydes, and six types of VOCs were detected, but they were within the standard. As a result of by calculating the odor contribution, the contribution of 74.9 % or more was found at the point where butyraldehyde was detected. Therefore, in order to prevent odors at the Yeosu Industrial Complex, measures to reduce aldehydes with high odor contribution should be prioritized, and it is necessary to simultaneously investigate through real-time harmful atmospheric measurement vehicles. Based on the contents presented in this study, if the system and policies reflecting the results of the odor occurrence survey of Yeosu National Industrial Complex and surrounding areas are supplemented, the odor environment of Yeosu National Industrial Complex will be sufficiently improved.
- Open Access
- 19 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 7, 46917-46930
A New Parameter Repurposing Method for Parameter Transfer With Small Dataset and Its Application in Fault Diagnosis of Rolling Element Bearings
Transfer learning is a promising deep learning approach that can be used in applications that suffer from insufficient training data. Parameter transfer, which is a method of improving the accuracy and training speed by training the target network using the parameters of the source network, selects two conventional parameter repurposing methods such as parameter freezing and fine tuning depending on the amount of target data and network size. In this paper, we propose a novel method to increase performance in the target domain in an intermediate approach of both methods. The proposed method, selective parameter freezing (SPF) freezes only a portion of parameters not freeze or fine-tune all parameters within a layer by choosing output-sensitive parameters from the source network. Freezing only sensitive parameters while training is to reduce the amount of trainable parameter and protect informative parameters from overfitting to small number of target data. Using two sets source-target domain, 1) artificial faults with different fault size, 2) artificial faults – natural faults of rolling element bearing, the proposed SPF allows adaptation to the target domain by choosing best degree of freezing with various amount of target data and size of networks, compared to conventional approaches.
- 19 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 7, 46917-46930
Open AccessA New Parameter Repurposing Method for Parameter Transfer With Small Dataset and Its Application in Fault Diagnosis of Rolling Element Bearings
Transfer learning is a promising deep learning approach that can be used in applications that suffer from insufficient training data. Parameter transfer, which is a method of improving the accuracy and training speed by training the target network using the parameters of the source network, selects two conventional parameter repurposing methods such as parameter freezing and fine tuning depending on the amount of target data and network size. In this paper, we propose a novel method to increase performance in the target domain in an intermediate approach of both methods. The proposed method, selective parameter freezing (SPF) freezes only a portion of parameters not freeze or fine-tune all parameters within a layer by choosing output-sensitive parameters from the source network. Freezing only sensitive parameters while training is to reduce the amount of trainable parameter and protect informative parameters from overfitting to small number of target data. Using two sets source-target domain, 1) artificial faults with different fault size, 2) artificial faults – natural faults of rolling element bearing, the proposed SPF allows adaptation to the target domain by choosing best degree of freezing with various amount of target data and size of networks, compared to conventional approaches.
- 1 September 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1 (23293721) , 1791-1794
Resonant Power shoes for humanoid robots
A robust wireless power transfer system, containing primary and secondary coils, for a humanoid robot is proposed in this paper. Multiple primary coils constitute a `Power mattress' structure on the ground, and a few secondary coils constitute a `Power shoe' of a humanoid robot. When the foot wearing the power shoe is on the power mattress, a strong magnetic linkage is built up between the shoe and mattress; so wireless power is transferred through resonated circuits. When the foot is away from the mattress, then no power transfer occurs. Experiments for a power shoe of 2×4 coils with 2 cm square and a power mattress of 6×7 coils with 2.5 cm square at 133 kHz show robust power delivery characteristics regardless of footage with the maximum output power of 23.3 W.
- 1 September 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1 (23293721) , 1791-1794
Resonant Power shoes for humanoid robots
A robust wireless power transfer system, containing primary and secondary coils, for a humanoid robot is proposed in this paper. Multiple primary coils constitute a `Power mattress' structure on the ground, and a few secondary coils constitute a `Power shoe' of a humanoid robot. When the foot wearing the power shoe is on the power mattress, a strong magnetic linkage is built up between the shoe and mattress; so wireless power is transferred through resonated circuits. When the foot is away from the mattress, then no power transfer occurs. Experiments for a power shoe of 2×4 coils with 2 cm square and a power mattress of 6×7 coils with 2.5 cm square at 133 kHz show robust power delivery characteristics regardless of footage with the maximum output power of 23.3 W.