Fei Zhou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Fei Zhou has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Qingjiang Xia
School of Integrated Circuits, Peking University, Beijing, China
6 shared publications - Wengao Lu
School of Integrated Circuits, Peking University, Beijing, China
6 shared publications - Yacong Zhang
School of Integrated Circuits, Peking University, Beijing, China
6 shared publications Yuze Niu
Technical Development Department, Lingfeng Vision Chip Beijing Technology Co, Ltd, Beijing, China
6 shared publications- Zhongjian Chen
School of Integrated Circuits, Peking University, Beijing, China
6 shared publications - Xuefei Du
School of Integrated Circuits, Peking University, Beijing, China
3 shared publications
Latest Publications
- 2 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. PP (15497747) , 1
A 1280 × 1024 SWIR DROIC With Self-Correcting Phase-Coded TDC-interpolated Single-Slope ADC
This brief presents a 1280 × 1024 pixel-array, 10 μm-pitch digital readout integrated circuit (DROIC), fabricated in a 180-nm CMOS process and hybrid-integrated with an InGaAs sensor array for megapixel-level short-wave infrared (SWIR) imaging. The DROIC employs a column-parallel analog-to-digital converter (ADC) architecture, in which a 2-bit time-to-digital converter (TDC) is incorporated into a 12-bit single-slope (SS) ADC to quantize the residual signal. A chip-shared multiphase clock generator scheme is adopted to provide uniform phase references with small area and low power overhead. To address coarse-fine stitching errors caused by chip-shared multiphase clock distribution, a self-correcting phase-coded stitching scheme is proposed. The proposed self-correcting phase-coded stitching scheme mitigates SNR degradation and improves column-to-column uniformity by suppressing jump code errors. The hybrid-integrated SWIR focal-plane array (FPA) achieves an array-averaged SNR of 83.44 dB and a random noise of 4.2 e−rms, while the measured dark fixed-pattern noise (FPN) is 0.11%. The FPA consumes 408 mW at a frame rate of 60 Hz, achieving a power efficiency of 427.16 fJ/LSB. These results demonstrate excellent noise performance, low FPN, and high energy efficiency for megapixel-level SWIR imaging.
- 2 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. PP (15497747) , 1
A 1280 × 1024 SWIR DROIC With Self-Correcting Phase-Coded TDC-interpolated Single-Slope ADC
This brief presents a 1280 × 1024 pixel-array, 10 μm-pitch digital readout integrated circuit (DROIC), fabricated in a 180-nm CMOS process and hybrid-integrated with an InGaAs sensor array for megapixel-level short-wave infrared (SWIR) imaging. The DROIC employs a column-parallel analog-to-digital converter (ADC) architecture, in which a 2-bit time-to-digital converter (TDC) is incorporated into a 12-bit single-slope (SS) ADC to quantize the residual signal. A chip-shared multiphase clock generator scheme is adopted to provide uniform phase references with small area and low power overhead. To address coarse-fine stitching errors caused by chip-shared multiphase clock distribution, a self-correcting phase-coded stitching scheme is proposed. The proposed self-correcting phase-coded stitching scheme mitigates SNR degradation and improves column-to-column uniformity by suppressing jump code errors. The hybrid-integrated SWIR focal-plane array (FPA) achieves an array-averaged SNR of 83.44 dB and a random noise of 4.2 e−rms, while the measured dark fixed-pattern noise (FPN) is 0.11%. The FPA consumes 408 mW at a frame rate of 60 Hz, achieving a power efficiency of 427.16 fJ/LSB. These results demonstrate excellent noise performance, low FPN, and high energy efficiency for megapixel-level SWIR imaging.
- 10 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (10) , 15551-15563
A 16-Channel Front-End ASIC With Adaptive Capacitive Level-Shifting PGA and 16-bit 1-MS/s Hybrid SAR ADC for Cryogenic Infrared Imagers
This paper presents a 16-channel front-end application specific integrated circuit (ASIC) for cryogenic infrared focal plane arrays (IRFPAs), targeting the critical constraints of sensor interface compatibility and system-level detection sensitivity. To address the wide output common-mode (CM) voltage variations inherent in various IRFPA readout integrated circuits (ROICs), an adaptive capacitive level-shifting (ACLS) programmable gain amplifier (PGA) is proposed. By reconfiguring the negative-path sampling capacitor array as an 8-bit capacitive digital-to-analog converter (CDAC) for adaptive level shifting, the PGA achieves a rail-to-rail input CM range, effectively maximizing the sensor system dynamic range without additional area or power overhead. Furthermore, a calibration-free 16-bit successive approximation register (SAR) analog-to-digital converter (ADC) based on a capacitor-resistor (C-R) hybrid DAC is proposed to ensure high intrinsic linearity. A 5-bit flash sub-ADC sharing the resistor ladder with the C-R hybrid DAC is integrated to accelerate MSB coarse quantization, thereby relaxing the RDAC settling constraint for 1-MS/s operation while minimizing static power consumption. The calibration-free architecture avoids the per-channel calibration overhead that scales poorly with channel count, ensuring readout consistency across the 16-channel array. Four on-chip low-dropout regulators (LDOs) and four voltage driver buffers associated with an 8-channel 12-bit DAC are integrated to locally regulate supply and bias voltages in close proximity to the IRFPA. This on-chip power management decouples the supply rails from cryogenic-to-ambient interconnect parasitics, suppressing voltage ripples and minimizing thermal loading through cryostat feedthroughs. Fabricated in a 180-nm CMOS process, the ASIC occupies 39.6 mm2. Measured at 77 K, the chip exhibits a total power consumption of 97.54mW. Operating at 1 MS/s with a 3.3 V supply, the SAR ADC achieves a signal-to-noise-and-distortion ratio (SNDR) of 81.08 dB.The measured differential nonlinearity (DNL) and integral nonlinearity (INL) are −0.61/+0.96 LSB and −4.26/+4.29 LSB, respectively. Each ADC channel consumes 1.92 mW, yielding a Schreier figure of merit (FoMS) of 165.2 dB. Validated with a long-wave IRFPA, the ASIC enables high-fidelity cryogenic imaging, demonstrating its effectiveness in high-precision cryogenic sensing systems.
- 10 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (10) , 15551-15563
A 16-Channel Front-End ASIC With Adaptive Capacitive Level-Shifting PGA and 16-bit 1-MS/s Hybrid SAR ADC for Cryogenic Infrared Imagers
This paper presents a 16-channel front-end application specific integrated circuit (ASIC) for cryogenic infrared focal plane arrays (IRFPAs), targeting the critical constraints of sensor interface compatibility and system-level detection sensitivity. To address the wide output common-mode (CM) voltage variations inherent in various IRFPA readout integrated circuits (ROICs), an adaptive capacitive level-shifting (ACLS) programmable gain amplifier (PGA) is proposed. By reconfiguring the negative-path sampling capacitor array as an 8-bit capacitive digital-to-analog converter (CDAC) for adaptive level shifting, the PGA achieves a rail-to-rail input CM range, effectively maximizing the sensor system dynamic range without additional area or power overhead. Furthermore, a calibration-free 16-bit successive approximation register (SAR) analog-to-digital converter (ADC) based on a capacitor-resistor (C-R) hybrid DAC is proposed to ensure high intrinsic linearity. A 5-bit flash sub-ADC sharing the resistor ladder with the C-R hybrid DAC is integrated to accelerate MSB coarse quantization, thereby relaxing the RDAC settling constraint for 1-MS/s operation while minimizing static power consumption. The calibration-free architecture avoids the per-channel calibration overhead that scales poorly with channel count, ensuring readout consistency across the 16-channel array. Four on-chip low-dropout regulators (LDOs) and four voltage driver buffers associated with an 8-channel 12-bit DAC are integrated to locally regulate supply and bias voltages in close proximity to the IRFPA. This on-chip power management decouples the supply rails from cryogenic-to-ambient interconnect parasitics, suppressing voltage ripples and minimizing thermal loading through cryostat feedthroughs. Fabricated in a 180-nm CMOS process, the ASIC occupies 39.6 mm2. Measured at 77 K, the chip exhibits a total power consumption of 97.54mW. Operating at 1 MS/s with a 3.3 V supply, the SAR ADC achieves a signal-to-noise-and-distortion ratio (SNDR) of 81.08 dB.The measured differential nonlinearity (DNL) and integral nonlinearity (INL) are −0.61/+0.96 LSB and −4.26/+4.29 LSB, respectively. Each ADC channel consumes 1.92 mW, yielding a Schreier figure of merit (FoMS) of 165.2 dB. Validated with a long-wave IRFPA, the ASIC enables high-fidelity cryogenic imaging, demonstrating its effectiveness in high-precision cryogenic sensing systems.
- 3 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73 (7) , 4506-4518
A 15-fJ/Step, 82.4-dB SNR SAR Capacitance-to-Digital Converter With System-Level Correlated Double Sampling
This paper presents a 16-bit, energy-efficient, fully dynamic successive-approximation-register (SAR) capacitance-to-digital converter (CDC) for single-ended capacitive sensors. A system-level correlated-double-sampling (CDS) scheme is proposed to suppress errors arising from comparator offset, low-frequency noise, and external interference. The delay time characteristics of the inverter-based amplifier (FIA) comparator are characterized for the first time, and an optimal delay time is determined through simulation. An LSB-repetition scheme improves low-noise performance. Dual digital-supply technique reduces the power consumption of the digital circuitry and also extend the delay time of digital delay elements with minimal power overhead, thereby improving energy efficiency. Fabricated in a 180-nm CMOS process, the CDC is validated using a capacitive MEMS pressure sensor, achieving a best resolution of 0.27 fF and a signal-to-noise ratio (SNR) of 82.6 dB among SAR CDCs. Consuming $2.85~\mu $ W with a $56~\mu $ s conversion time, it achieves a Walden figure-of-merit ( $FoM_{w}$ ) of 15 fJ/step. The CDC attains a DNL of -0.76/+0.85 LSB and an INL of -9.16/+9.15 LSB without calibration. Experimental results demonstrate more than $16\times $ improvement in interference rejection at 100 Hz and more than $7\times $ improvement under 1000 Hz, compared to a non-CDS implementation.
- 3 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73 (7) , 4506-4518
A 15-fJ/Step, 82.4-dB SNR SAR Capacitance-to-Digital Converter With System-Level Correlated Double Sampling
This paper presents a 16-bit, energy-efficient, fully dynamic successive-approximation-register (SAR) capacitance-to-digital converter (CDC) for single-ended capacitive sensors. A system-level correlated-double-sampling (CDS) scheme is proposed to suppress errors arising from comparator offset, low-frequency noise, and external interference. The delay time characteristics of the inverter-based amplifier (FIA) comparator are characterized for the first time, and an optimal delay time is determined through simulation. An LSB-repetition scheme improves low-noise performance. Dual digital-supply technique reduces the power consumption of the digital circuitry and also extend the delay time of digital delay elements with minimal power overhead, thereby improving energy efficiency. Fabricated in a 180-nm CMOS process, the CDC is validated using a capacitive MEMS pressure sensor, achieving a best resolution of 0.27 fF and a signal-to-noise ratio (SNR) of 82.6 dB among SAR CDCs. Consuming $2.85~\mu $ W with a $56~\mu $ s conversion time, it achieves a Walden figure-of-merit ( $FoM_{w}$ ) of 15 fJ/step. The CDC attains a DNL of -0.76/+0.85 LSB and an INL of -9.16/+9.15 LSB without calibration. Experimental results demonstrate more than $16\times $ improvement in interference rejection at 100 Hz and more than $7\times $ improvement under 1000 Hz, compared to a non-CDS implementation.
- 14 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 33 (10) , 2663-2667
An Energy-Efficient Four-Channel Interface ASIC for IRFPAs With Optimized Resistor-Sharing Technique Achieving 88.1-dB SNDR
This article presents a four-channel interface application-specific integrated circuit (ASIC) for infrared focal plane arrays (IRFPAs), where each channel integrates a programmable gain amplifier (PGA) with wide-range input common-mode adjustment capability and a 16-bit hybrid analog-to-digital converter (ADC) with resistor-sharing technique (RST). The flash stage of the ADC performs 5-bit most significant bits (MSBs) conversion, whose results are transferred to thermometer-coded capacitor array in the successive approximation register (SAR) stage, ensuring high linearity while maintaining conversion speed. This hybrid architecture of the ADC uses the RST by sharing the resistor ladder between the flash and SAR stages, reducing power consumption. The interface ASIC fabricated in the 180-nm CMOS technology achieves an input common-mode adjustment range of 0.169–3.269 V. Operating at 2 MS/s with a 3.3-V supply, it achieves an 88.1-dB signal-to-noise-and-distortion ratio (SNDR) and consumes 13.97 mW/channel. The Schreier figure-of-merit (FoM) of the ADC reaches 171.2 dB/channel. Measured differential and integral nonlinearity (DNL/INL) are −0.38/+0.49 least significant bits (LSBs) and −2.2/+1.4 LSB, respectively.
- 14 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 33 (10) , 2663-2667
An Energy-Efficient Four-Channel Interface ASIC for IRFPAs With Optimized Resistor-Sharing Technique Achieving 88.1-dB SNDR
This article presents a four-channel interface application-specific integrated circuit (ASIC) for infrared focal plane arrays (IRFPAs), where each channel integrates a programmable gain amplifier (PGA) with wide-range input common-mode adjustment capability and a 16-bit hybrid analog-to-digital converter (ADC) with resistor-sharing technique (RST). The flash stage of the ADC performs 5-bit most significant bits (MSBs) conversion, whose results are transferred to thermometer-coded capacitor array in the successive approximation register (SAR) stage, ensuring high linearity while maintaining conversion speed. This hybrid architecture of the ADC uses the RST by sharing the resistor ladder between the flash and SAR stages, reducing power consumption. The interface ASIC fabricated in the 180-nm CMOS technology achieves an input common-mode adjustment range of 0.169–3.269 V. Operating at 2 MS/s with a 3.3-V supply, it achieves an 88.1-dB signal-to-noise-and-distortion ratio (SNDR) and consumes 13.97 mW/channel. The Schreier figure-of-merit (FoM) of the ADC reaches 171.2 dB/channel. Measured differential and integral nonlinearity (DNL/INL) are −0.38/+0.49 least significant bits (LSBs) and −2.2/+1.4 LSB, respectively.
- 14 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 72 (5) , 678-682
An Energy-Efficient Capacitance-to-Digital Converter With Top and Bottom Plate Sampling for Pressure Sensors
This brief presents a 12-bit low-power successive-approximation-register (SAR) capacitance-to-digital converter (CDC) for capacitive pressure sensors. It adopts a capacitance-to-voltage front-end (CVFE) scheme to decouple the capacitive digital-to-analog converter (CDAC) from the sensor capacitor, enabling a large swing of the SAR analog-to-digital converter (ADC) and a wide capacitance sensing range. To improve power efficiency, this brief proposed a top and bottom sampling (TBS) for CVFE circuit to achieve a single-ended sampling while differential conversion. The TBS includes only one sampling phase, which relaxes the amplifier’s bandwidth requirements, thereby reducing the power consumption of the CVFE. The prototype chip was fabricated using a 180-nm CMOS process. The measured capacitance resolution is 1.76 fF and the measurement capacitance range is from 0.63 pF to 38.37 pF. The proposed CDC consumes 3.90 μW with a 128 μs conversion time, bringing a power efficiency of 80.6 fJ/conversion-step.
- 14 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 72 (5) , 678-682
An Energy-Efficient Capacitance-to-Digital Converter With Top and Bottom Plate Sampling for Pressure Sensors
This brief presents a 12-bit low-power successive-approximation-register (SAR) capacitance-to-digital converter (CDC) for capacitive pressure sensors. It adopts a capacitance-to-voltage front-end (CVFE) scheme to decouple the capacitive digital-to-analog converter (CDAC) from the sensor capacitor, enabling a large swing of the SAR analog-to-digital converter (ADC) and a wide capacitance sensing range. To improve power efficiency, this brief proposed a top and bottom sampling (TBS) for CVFE circuit to achieve a single-ended sampling while differential conversion. The TBS includes only one sampling phase, which relaxes the amplifier’s bandwidth requirements, thereby reducing the power consumption of the CVFE. The prototype chip was fabricated using a 180-nm CMOS process. The measured capacitance resolution is 1.76 fF and the measurement capacitance range is from 0.63 pF to 38.37 pF. The proposed CDC consumes 3.90 μW with a 128 μs conversion time, bringing a power efficiency of 80.6 fJ/conversion-step.