Hao Qi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Hao Qi has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Junfei Wu
College of Electromechanical Engineering, Qingdao University of Science and Technology, Qingdao 266061, China
2 shared publications - Ning Kuang
College of Electromechanical Engineering, Qingdao University of Science and Technology, Qingdao 266061, China
2 shared publications - Wenjie Zhao
College of Sino-German Science and Technology, Qingdao University of Science and Technology, Qingdao 266061, China
2 shared publications - Minghui Xiao
College of Electromechanical Engineering, Qingdao University of Science and Technology, Qingdao 266061, China
1 shared publication
Latest Publications
- Open Access
Influence of Resin Composition on the Photopolymerization of Zirconia Ceramics Fabricated by Digital Light Processing Additive Manufacturing
Digital light processing (DLP) is widely recognized as one of the most promising additive manufacturing technologies for ceramic fabrication. Nevertheless, during the additive manufacturing of zirconia ceramics, debinding and sintering often lead to structural defects, which severely deteriorate the material properties and hinder their broader application. In this study, we added an oligomer into the photosensitive resin and systematically investigated the effects of oligomer content on the viscosity and curing properties of ceramic suspensions. The results demonstrated that the introduction of oligomers is conducive to enhancing the crosslinking density and reducing defects. Finally, a 45 vol% solid content zirconia ceramic slurry was prepared by adding 20 wt% oligomers to the resin system. After printing, debinding, and sintering, the final zirconia ceramics exhibited a uniform microstructure without delamination or cracks, its bending strength reached 682.4 MPa. This study demonstrates that zirconia ceramics fabricated by photopolymerization with oligomer photosensitive resin exhibit excellent mechanical properties, significantly expanding the potential applications for high-performance zirconia ceramic components with additive manufacturing.
Open AccessInfluence of Resin Composition on the Photopolymerization of Zirconia Ceramics Fabricated by Digital Light Processing Additive Manufacturing
Digital light processing (DLP) is widely recognized as one of the most promising additive manufacturing technologies for ceramic fabrication. Nevertheless, during the additive manufacturing of zirconia ceramics, debinding and sintering often lead to structural defects, which severely deteriorate the material properties and hinder their broader application. In this study, we added an oligomer into the photosensitive resin and systematically investigated the effects of oligomer content on the viscosity and curing properties of ceramic suspensions. The results demonstrated that the introduction of oligomers is conducive to enhancing the crosslinking density and reducing defects. Finally, a 45 vol% solid content zirconia ceramic slurry was prepared by adding 20 wt% oligomers to the resin system. After printing, debinding, and sintering, the final zirconia ceramics exhibited a uniform microstructure without delamination or cracks, its bending strength reached 682.4 MPa. This study demonstrates that zirconia ceramics fabricated by photopolymerization with oligomer photosensitive resin exhibit excellent mechanical properties, significantly expanding the potential applications for high-performance zirconia ceramic components with additive manufacturing.
- Open Access
Optimization of Resin Composition for Zirconia Ceramic Digital Light Processing Additive Manufacturing
In ceramic digital light processing (DLP) additive manufacturing, the photosensitive resin, which acts as a carrier for ceramic particles, must exhibit suitable curing performance, curing strength, and viscosity. This ensures both the bonding strength of the fabricated ceramic parts and the dimensional accuracy of the ceramic green body. In this study, various photosensitive resin monomers were investigated in depth to formulate resins containing monofunctional, bifunctional, and multifunctional groups. Their rheological and curing properties were analyzed theoretically and experimentally. Different resin slurry systems were prepared and printed using DLP technology, and their mechanical properties were tested and compared. The effect of photoinitiator content on the curing behavior of the resin was examined, and the optimal photoinitiator concentration was identified. Based on the optimized resin, a zirconia ceramic slurry with 56 vol% solid content was prepared. After DLP printing, debinding, and sintering, dense zirconia ceramic samples with a relatively uniform grain structure were obtained, exhibiting a bending strength of 766.85 MPa. These results significantly expand the potential applications for zirconia ceramic components with complex geometries.
Open AccessOptimization of Resin Composition for Zirconia Ceramic Digital Light Processing Additive Manufacturing
In ceramic digital light processing (DLP) additive manufacturing, the photosensitive resin, which acts as a carrier for ceramic particles, must exhibit suitable curing performance, curing strength, and viscosity. This ensures both the bonding strength of the fabricated ceramic parts and the dimensional accuracy of the ceramic green body. In this study, various photosensitive resin monomers were investigated in depth to formulate resins containing monofunctional, bifunctional, and multifunctional groups. Their rheological and curing properties were analyzed theoretically and experimentally. Different resin slurry systems were prepared and printed using DLP technology, and their mechanical properties were tested and compared. The effect of photoinitiator content on the curing behavior of the resin was examined, and the optimal photoinitiator concentration was identified. Based on the optimized resin, a zirconia ceramic slurry with 56 vol% solid content was prepared. After DLP printing, debinding, and sintering, dense zirconia ceramic samples with a relatively uniform grain structure were obtained, exhibiting a bending strength of 766.85 MPa. These results significantly expand the potential applications for zirconia ceramic components with complex geometries.