Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Zhengjian Pan has a total of 23 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Optimization of Loading Path for Hydroforming of Asymmetric Curved Tubes Using AMGA

    by Zaixiang Zheng, Hui Tan, Gang Wu, Feng Wang, Siyuan Tang, Yujie Chen, Yang Zhao, Hantao Yu, Zhengjian Pan

    The hydroforming performance of trailing arms is governed by the coupled effects of feed parameters, pressure schedules and frictional characteristics. Improper parameter matching readily induces typical forming defects such as wrinkling, cracking and uneven wall thickness. To address this issue, a multi-objective optimization method for hydroforming is proposed in this study. Taking the maximum wall thickness, minimum wall thickness and die-to-workpiece gap of the tubular blank as optimization objectives, and the internal pressure and right-side axial feed velocity as design variables, an integrated numerical simulation framework combining the Archive-based Micro Genetic Algorithm (AMGA) and LS-DYNA is established to analyze the hydroforming process. By adaptively adjusting the key control points of internal pressure and axial feed loading curves, the developed method expands the solution space and realizes the automatic optimization of loading paths. The results reveal that the maximum wall thinning rate of the tubular component drops from 20.4% to 14.8%. Meanwhile, the wall thickness uniformity is improved and forming defects are effectively suppressed while the thickening rate remains stable. Furthermore, a complete round of optimization calculation involving thousands of finite element solutions can yield a complete set of Pareto non-dominated solutions. In this paper, the AMGA multi-objective optimization algorithm is adopted to acquire the optimal loading paths, and physical prototype experiments are carried out relying on self-developed 2000 T hydroforming equipment. Comparisons between measured and simulated wall thickness values of the tubular component show that the maximum relative error is controlled within 7.46%, which verifies the reliable engineering applicability of the proposed optimization scheme and provides new insight into the process optimization for forming similar structural components.

  • Open Access

    Optimization of Loading Path for Hydroforming of Asymmetric Curved Tubes Using AMGA Algorithm

    by Zaixiang Zheng, Hui Tan, Gang Wu, Feng Wang, Siyuan Tang, Yujie Chen, Yang Zhao, Hantao Yu, Zhengjian Pan

    The hydroforming performance of trailing arms is governed by the coupled effects of feed parameters, pressure schedules and frictional characteristics. Improper parameter matching readily induces typical forming defects such as wrinkling, cracking and uneven wall thickness. To address this issue, a multi-objective optimization method for hydroforming is proposed in this study. Taking the maximum wall thickness, minimum wall thickness and die-to-workpiece gap of the tubular blank as optimization objectives, and the internal pressure and right-side axial feed velocity as design variables, an integrated numerical simulation framework combining the Archive-based Micro Genetic Algorithm (AMGA) and LS-DYNA is established to analyze the hydroforming process. By adaptively adjusting the key control points of internal pressure and axial feed loading curves, the developed method expands the solution space and realizes the automatic optimization of loading paths. The results reveal that the maximum wall thickness reduction rate of the tubular component is reduced from 20.4% to 14.8%. Meanwhile, the wall thickness uniformity is improved and forming defects are effectively suppressed while the thickening rate remains stable. Moreover, multiple sets of Pareto optimal solutions can be obtained in a single calculation. This work provides new insight into the process optimization for forming similar structural components.

  • Open Access

    Research on Multi-Objective Optimization Method for Hydroforming Loading Path of Centralizer

    by Zaixiang Zheng, Zhengjian Pan, Hui Tan, Feng Wang, Jing Xu, Yiyang Gu, Guoheng Li

    During centralizer hydroforming, internal pressure and axial feed critically influence the forming outcome. Insufficient feed causes excessive thinning and cracking, while excessive feed causes thickening and wrinkling. Achieving uniform wall thickness necessitates careful design of the pressure and feed curves. Using max/min wall thickness as objectives and key control points on these curves as variables, the study integrated Non-dominated Sorting Genetic Algorithm (NSGA-II), Multi-Objective Particle Swarm Optimization (MOPSO), Neighborhood Cultivation Genetic Algorithm (NCGA), and Archive-based Micro Genetic Algorithm (AMGA) with LS-DYNA to automatically optimize loading paths. The results demonstrate the following: ① NSGA-II, NCGA, and AMGA successfully generated optimized paths; ② NSGA-II and AMGA produced larger sets of higher-quality Pareto solutions; ③ AMGA required more iterations for satisfactory Pareto sets; ④ MOPSO exhibited a tendency towards premature convergence, yielding inferior results; ⑤ Multi-objective optimization efficiently generated diverse Pareto solutions, expanding the design space for process design.


  • Open Access

    Optimization of loading path for internal high-pressure forming of instrument panel tube beam based on NSGA-II

    by Zaixiang Zheng, Zihao Yao, Zhengjian Pan

    In the process of hydroforming of instrument panel tube beams (IPTB), the rationality of the internal pressure loading curve (IPLC), and the axial feed curve (AFC), directly determines the success or failure of the forming. However, due to their inherent limitations, traditional analytical methods, experimental methods, and numerical simulation (SIM) methods are difficult to achieve ideal results in the matching design of multivariable loading paths. To this end, this paper combines the elite retention non-inferior sorting genetic algorithm (NSGA-II) with commercial finite element software based on dynamic explicit algorithm and realizes the optimal design of the loading path by adjusting the values of key control points on the IPLC and the axial feed speed curve (AFSC). The optimization results show that by reasonably setting the population size (PS) and number of generations (NG), a loading path closer to the optimal can be obtained compared with the manual optimization method, and the wall thickness (WT) distribution of the IPTB is more uniform. In addition, this method can generate multiple Pareto optimal solutions simultaneously in one optimization, providing more options for the formulation of loading paths.


  • Open Access

    Panet al.Reply:

    by Z.-H. Pan, A. V. Fedorov, C. A. Howard, M. Ellerby, T. Valla

    A Reply to the Comment by M. Calandra et al..