Kenneth K.S. Lau
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Kenneth K.S. Lau has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Alexis Linard
EECS and Digital Futures, KTH Royal Institute of Technology, Stockholm, 100 44, Sweden
1 shared publication - Anna Maria Coclite
Institute of Solid State Physics NAWI Graz Graz University of Technology Graz 8010 Austria
1 shared publication - David Broman
KTH Royal Institute of Technology, Stockholm, Sweden
1 shared publication - David Tilly
Elekta Instrument AB, Hagaesplanaden 4, Stockholm, 113 68, Sweden
1 shared publication - Fabian Muralter
Institute of Solid State Physics, NAWI Graz, Graz University of Technology, Petersgasse 16, 8010 Graz, Austria
1 shared publication - Henrik Rehbinder
Elekta Instrument AB, Hagaesplanaden 4, Stockholm, 113 68, Sweden
1 shared publication
Latest Publications
- Open Access
- 28 March 2026
- Published by Elsevier in Artificial Intelligence in Medicine
- Vol. 177, 103413
Reinforcement learning for real-time adaptive radiotherapy
- 28 March 2026
- Published by Elsevier in Artificial Intelligence in Medicine
- Vol. 177, 103413
Open AccessReinforcement learning for real-time adaptive radiotherapy
- Open Access
- 28 December 2020
- Published by Wiley in Advanced Electronic Materials
- Vol. 7 (2)
Oxidative Chemical Vapor Deposition of Conducting Polymer Films on Nanostructured Surfaces for Piezoresistive Sensor Applications
In this study, a novel, fully polymeric setup for piezoresistive sensing is prepared and tested. Monolayers of polystyrene (PS) nanospheres are assembled on flexible polyethylene naphthalate substrates. Subsequently, thin layers (≈50–100 nm) of poly(3,4‐ethylenedioxythiophene) (PEDOT) are deposited conformally around the spheres by oxidative chemical vapor deposition (oCVD). Voltage−current characteristics and direct resistance measurements are performed to test the electrical properties of the samples in their unstrained state and their piezoresistive response during bending. Substrate deposition temperature (Tsub) and film thickness (tPEDOT) are used as parameters to alter properties of the PEDOT thin films; increased Tsub and tPEDOT lead to samples exhibiting lower intrinsic resistance. The electrical conductivity of the samples is estimated to range as high as tens of S cm−1. Dopant exchange of the oCVD‐PEDOT layer (intrinsically, chlorine‐doped) is performed by putting the samples in 0.5 m sulfuric acid, which decreases their resistance by ≈1/3. Regarding the piezoresistive properties of the devices, acid treatment, higher Tsub and tPEDOT (thus, lower intrinsic resistance) yield samples with increased response. As a result, gauge factors as high as 11.4 are achieved. Due to their flexibility and low‐cost, the proposed structures can be readily employed as skin‐inspired or wearable electronic devices.
- 28 December 2020
- Published by Wiley in Advanced Electronic Materials
- Vol. 7 (2)
Open AccessOxidative Chemical Vapor Deposition of Conducting Polymer Films on Nanostructured Surfaces for Piezoresistive Sensor Applications
In this study, a novel, fully polymeric setup for piezoresistive sensing is prepared and tested. Monolayers of polystyrene (PS) nanospheres are assembled on flexible polyethylene naphthalate substrates. Subsequently, thin layers (≈50–100 nm) of poly(3,4‐ethylenedioxythiophene) (PEDOT) are deposited conformally around the spheres by oxidative chemical vapor deposition (oCVD). Voltage−current characteristics and direct resistance measurements are performed to test the electrical properties of the samples in their unstrained state and their piezoresistive response during bending. Substrate deposition temperature (Tsub) and film thickness (tPEDOT) are used as parameters to alter properties of the PEDOT thin films; increased Tsub and tPEDOT lead to samples exhibiting lower intrinsic resistance. The electrical conductivity of the samples is estimated to range as high as tens of S cm−1. Dopant exchange of the oCVD‐PEDOT layer (intrinsically, chlorine‐doped) is performed by putting the samples in 0.5 m sulfuric acid, which decreases their resistance by ≈1/3. Regarding the piezoresistive properties of the devices, acid treatment, higher Tsub and tPEDOT (thus, lower intrinsic resistance) yield samples with increased response. As a result, gauge factors as high as 11.4 are achieved. Due to their flexibility and low‐cost, the proposed structures can be readily employed as skin‐inspired or wearable electronic devices.