Weidong Cheng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Weidong Cheng has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
Mengyuan Zhao
Tianneng New Energy (Huzhou) Co., China; Qiqihar University, China
2 shared publicationsZhaojun Wu
Qiqihar University, China
2 shared publicationsDonghong Zhang
School of Agricultural Engineering and Food Science, Shandong University of Technology
1 shared publication- Hang Xu
School of Microelectronics, Fudan University, Shanghai 200433, China
1 shared publication - Hongzhen Cai
Shandong Research Center of Engineering and Technology for Clean Energy, Zibo 255000, China
1 shared publication Huanyan Liu
1 shared publication
Latest Publications
- Open Access
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 29
In Situ SAXS Investigation of Bi-Bi2O3/C Anode Materials for Lithium-Ion Batteries Under Operational Conditions
Bismuth has become one of the most promising anodes for lithium-ion batteries (LIBs) due to its suitable operating voltage and high volumetric capacity. However, the inevitable volume expansion of bismuth during the charge/discharge cycling process of lithium-ion batteries can lead to severe capacity fading and eventual battery failure. Herein, Bi-Bi2O3/C composite materials were prepared using a combination of solvothermal and calcination methods, and a series of characterization tests were conducted to investigate the effects of different secondary calcination times on the microstructure, composition, electrochemical properties, and the internal structural evolution during the initial charge/discharge cycle of the composite materials. In situ synchrotron radiation small angle X-ray scattering (SAXS) was employed to reveal the multi-level nanostructure evolution of Bi-Bi2O3/C electrode materials during charge/discharge processes. The present work reveals that these SAXS findings provide some new insights into the theoretical mechanism for the development of LIBs.
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 29
Open AccessIn Situ SAXS Investigation of Bi-Bi2O3/C Anode Materials for Lithium-Ion Batteries Under Operational Conditions
Bismuth has become one of the most promising anodes for lithium-ion batteries (LIBs) due to its suitable operating voltage and high volumetric capacity. However, the inevitable volume expansion of bismuth during the charge/discharge cycling process of lithium-ion batteries can lead to severe capacity fading and eventual battery failure. Herein, Bi-Bi2O3/C composite materials were prepared using a combination of solvothermal and calcination methods, and a series of characterization tests were conducted to investigate the effects of different secondary calcination times on the microstructure, composition, electrochemical properties, and the internal structural evolution during the initial charge/discharge cycle of the composite materials. In situ synchrotron radiation small angle X-ray scattering (SAXS) was employed to reveal the multi-level nanostructure evolution of Bi-Bi2O3/C electrode materials during charge/discharge processes. The present work reveals that these SAXS findings provide some new insights into the theoretical mechanism for the development of LIBs.
- 31 October 2023
- Published by Elsevier in Materials Today Communications
- Vol. 37
Study on microstructural evolutions and properties of the magnesium oxysulfate cement in the initial curing processes
- 31 October 2023
- Published by Elsevier in Materials Today Communications
- Vol. 37
Study on microstructural evolutions and properties of the magnesium oxysulfate cement in the initial curing processes
- Open Access
- 5 February 2022
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 29 (1) , 246-251
A Study of Test Suite Reduction Based on Ant Lion Optimizer
The development of smart meters to Internet of Things is the infrastructure for the Internet to carry out user electricity management and enhance user experience with electricity. As the iteration of smart home service system based on smart meters co...
- 5 February 2022
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 29 (1) , 246-251
Open AccessA Study of Test Suite Reduction Based on Ant Lion Optimizer
The development of smart meters to Internet of Things is the infrastructure for the Internet to carry out user electricity management and enhance user experience with electricity. As the iteration of smart home service system based on smart meters co...
- Open Access
- 3 December 2019
- Published by BioResources in BioResources
- Vol. 15 (1) , 557-573
Effect of moisture content during preparation on the physicochemical properties of pellets made from different biomass materials
The influence of moisture content was investigated relative to the pellet forming process and the pellet properties. Three different types of raw biomass (pine sawdust, corn straw, and peanut shell) were pelletized by hot pressing at different moisture levels (12%, 14%, and 16%) in a pellet mill with horizontal and ring type dies to investigate its physical property indexes of durability, pellet density, and combustion performance. The results of the study showed that pellet density and heating value were related to the moisture content. The maximum pellet density of the fuel pellets of sawdust, corn straw, and peanut shells was 1180 kg/m3, 1220 kg/m3, and 1130 kg/m3, respectively. The drop resistance and deformation resistance of pine sawdust and corn straw decreased with increased moisture content, but peanut shell initially increased with the increase of moisture before decreasing. The comprehensive combustion index of corn straw (14.03) was the highest during the combustion performance analysis in comparison to sawdust (11.10) and peanut shell (10.00). Overall, the optimal moisture content of sawdust, corn straw, and peanut shell was 12%, 12%, and 14%, respectively, and the combustion performance of the pellets made from corn straw was superior compared to the other two feedstocks.
- 3 December 2019
- Published by BioResources in BioResources
- Vol. 15 (1) , 557-573
Open AccessEffect of moisture content during preparation on the physicochemical properties of pellets made from different biomass materials
The influence of moisture content was investigated relative to the pellet forming process and the pellet properties. Three different types of raw biomass (pine sawdust, corn straw, and peanut shell) were pelletized by hot pressing at different moisture levels (12%, 14%, and 16%) in a pellet mill with horizontal and ring type dies to investigate its physical property indexes of durability, pellet density, and combustion performance. The results of the study showed that pellet density and heating value were related to the moisture content. The maximum pellet density of the fuel pellets of sawdust, corn straw, and peanut shells was 1180 kg/m3, 1220 kg/m3, and 1130 kg/m3, respectively. The drop resistance and deformation resistance of pine sawdust and corn straw decreased with increased moisture content, but peanut shell initially increased with the increase of moisture before decreasing. The comprehensive combustion index of corn straw (14.03) was the highest during the combustion performance analysis in comparison to sawdust (11.10) and peanut shell (10.00). Overall, the optimal moisture content of sawdust, corn straw, and peanut shell was 12%, 12%, and 14%, respectively, and the combustion performance of the pellets made from corn straw was superior compared to the other two feedstocks.