Ángel Triviño-Peláez
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ángel Triviño-Peláez has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Federico Rafael García-Galván
Department of Mechanical, Chemical and Industrial Design Engineering, ETSIDI, Universidad Politécnica de Madrid, 28010 Madrid, Spain
3 shared publications - Jose Antonio Jimenez
Department of Physical Metallurgy, National Center for Metallurgical Research (CENIM-CSIC), 28040 Madrid, Spain
3 shared publications - Raul Reyes-Riverol
National Centre for Metallurgical Research (CENIM-CSIC), Av. Gregorio del Amo 8, 28040 Madrid, Spain
3 shared publications - Santiago Fajardo
National Centre for Metallurgical Reserach (CENIM-CSIC)
2 shared publications - Davide Cademartori
Department of Civil, Chemical and Environmental Engineering, University of Genoa (UNIGE-DICCA), Via all’Opera Pia 15, 16145 Genoa, Italy
1 shared publication Domingo Pérez-Coll
Instituto de Cerámica y Vidrio (CSIC), Madrid, Spain
1 shared publication
Latest Publications
- Open Access
- 18 February 2026
- Published by Elsevier in SSRN Electronic Journal
Effect of Post-Processing Heat Treatments on the Microstructure and Corrosion Resistance of AZ91 Magnesium Alloy Produced by Laser Powder Bed Fusion
The influence of post-build heat treatments on the microstructure and corrosion behavior of LPBF-processed AZ91 Mg alloy was investigated. Solutionizing and over-aging treatments were applied to modify grain size and the morphology, distribution, and fraction of the β-Mg17Al12 phase. Corrosion behavior was evaluated in 0.1 M NaCl using potentiodynamic polarization, electrochemical impedance spectroscopy, hydrogen evolution measurements, and surface analyses. Over-aging promoted faster anodic kinetics and higher corrosion rates as a consequence of Al depletion from the solid solution and β-phase coarsening. In contrast, solutionizing promoted Al availability in solid solution and the formation of a pseudo-passive surface film, improving global corrosion resistance despite localized pitting.
- 18 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffect of Post-Processing Heat Treatments on the Microstructure and Corrosion Resistance of AZ91 Magnesium Alloy Produced by Laser Powder Bed Fusion
The influence of post-build heat treatments on the microstructure and corrosion behavior of LPBF-processed AZ91 Mg alloy was investigated. Solutionizing and over-aging treatments were applied to modify grain size and the morphology, distribution, and fraction of the β-Mg17Al12 phase. Corrosion behavior was evaluated in 0.1 M NaCl using potentiodynamic polarization, electrochemical impedance spectroscopy, hydrogen evolution measurements, and surface analyses. Over-aging promoted faster anodic kinetics and higher corrosion rates as a consequence of Al depletion from the solid solution and β-phase coarsening. In contrast, solutionizing promoted Al availability in solid solution and the formation of a pseudo-passive surface film, improving global corrosion resistance despite localized pitting.
- Open Access
- 1 September 2025
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 13 (9) , 4577-4595
Microstructure and electrochemical behavior of AZ91 Mg Alloy produced by laser powder bed fusion
- 1 September 2025
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 13 (9) , 4577-4595
Open AccessMicrostructure and electrochemical behavior of AZ91 Mg Alloy produced by laser powder bed fusion
- Open Access
Influence of Microstructure and Heat Treatment on the Corrosion Resistance of Mg-1Zn Alloy Produced by Laser Powder Bed Fusion
The corrosion behavior of an additively manufactured Mg-1Zn alloy was investigated in both the transverse and longitudinal directions relative to the build direction, in the as-built condition and after annealing at 350 °C for 24 h under high vacuum. Microstructural characterization using XRD and SEM revealed the presence of magnesium oxide (MgO) and the absence of intermetallic second-phase particles. Optical microscopy (OM) images and Electron Backscatter Diffraction (EBSD) maps showed a highly complex grain morphology with anomalous, anisotropic shapes and a heterogeneous grain size distribution. The microstructure includes grains with a pronounced columnar morphology aligned along the build direction and is therefore characterized by a strong crystallographic texture. Electrochemical techniques, including PDP and EIS, along with gravimetric H2 collection, concluded that the transverse plane exhibited greater corrosion resistance compared to the longitudinal plane. Additionally, an increase in cathodic kinetics was observed when comparing as-built with heat-treated samples.
Open AccessInfluence of Microstructure and Heat Treatment on the Corrosion Resistance of Mg-1Zn Alloy Produced by Laser Powder Bed Fusion
The corrosion behavior of an additively manufactured Mg-1Zn alloy was investigated in both the transverse and longitudinal directions relative to the build direction, in the as-built condition and after annealing at 350 °C for 24 h under high vacuum. Microstructural characterization using XRD and SEM revealed the presence of magnesium oxide (MgO) and the absence of intermetallic second-phase particles. Optical microscopy (OM) images and Electron Backscatter Diffraction (EBSD) maps showed a highly complex grain morphology with anomalous, anisotropic shapes and a heterogeneous grain size distribution. The microstructure includes grains with a pronounced columnar morphology aligned along the build direction and is therefore characterized by a strong crystallographic texture. Electrochemical techniques, including PDP and EIS, along with gravimetric H2 collection, concluded that the transverse plane exhibited greater corrosion resistance compared to the longitudinal plane. Additionally, an increase in cathodic kinetics was observed when comparing as-built with heat-treated samples.
- 11 February 2025
- Published by Elsevier in Electrochimica Acta
- Vol. 520
Modelling the impact of Ni migration and coarsening on the Ni-YSZ electrodes performances based on three-dimensional microstructures
- 11 February 2025
- Published by Elsevier in Electrochimica Acta
- Vol. 520
Modelling the impact of Ni migration and coarsening on the Ni-YSZ electrodes performances based on three-dimensional microstructures
- 4 July 2020
- Published by Springer Nature in Journal of Sol-Gel Science and Technology
- Vol. 95 (3) , 661-669
SrZr0.9Y0.1O3−δ thin films by in-situ synthesis of triple alkoxide for protonic ceramic electrolyser membranes
- 4 July 2020
- Published by Springer Nature in Journal of Sol-Gel Science and Technology
- Vol. 95 (3) , 661-669
SrZr0.9Y0.1O3−δ thin films by in-situ synthesis of triple alkoxide for protonic ceramic electrolyser membranes