Aisara Sabyrtayeva
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Aisara Sabyrtayeva has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Arman Zhanarbekovich Miniyazov
National Nuclear Center of the Republic of Kazakhstan, Kurchatov 180010, Kazakhstan
7 shared publications - Nuriya Mukhamedova
National Nuclear Center of the Republic of Kazakhstan (RSE NNC RK), Kurchatov 071100, Kazakhstan
7 shared publications - Ospan Oken
National Nuclear Center of the Republic of Kazakhstan (RSE NNC RK), Kurchatov 071100, Kazakhstan
7 shared publications - Igor Sokolov
National Nuclear Center of the Republic of Kazakhstan, Kurchatov 180010, Kazakhstan
4 shared publications - Zhanna Nurbolatovna Ospanova
The National Nuclear Center of the Republic of Kazakhstan, The Institute of Atomic Energy, Kurchatov 071100, Kazakhstan
4 shared publications - Bekmagambetova Balzhan
Branch “Institute of Atomic Energy” RSE NNC RK
2 shared publications
Latest Publications
- Open Access
Low-Temperature Thermomechanical Consolidation of Aluminosilicate Sorbents Impregnated with Model Oil-Containing Radioactive Waste
This paper investigates the possibility of pressure-assisted thermomechanical consolidation and thermal treatment without applied pressure during the low-temperature consolidation of oil-saturated aluminosilicate sorbents for their subsequent application in the conditioning of liquid oil-containing radioactive waste (RAW). The Premium and Absorbent sorbents saturated with transformer oil not containing radionuclides were used as model RAW systems. It was established that pressure-assisted thermomechanical consolidation leads to the formation of a denser structure and a reduction in hydrocarbon-phase losses compared with thermal treatment without applied pressure. For Premium, mass losses decreased from 0.74 to 0.35 g (by 53%), and for Absorbent, from 0.75 to 0.47 g (by 37%), and the consolidated samples were characterized by a more homogeneous microstructure and increased resistance to exudation. It was established that the efficiency of hydrocarbon-phase retention is determined by both the treatment conditions and the mineral composition of the sorbent. The obtained results indicate the prospects of low-temperature pressure-assisted thermomechanical consolidation at a temperature of 150 °C, a pressure of 1.5 MPa, and a holding time of 20 s for the conditioning of oil-containing RAW without the use of additional binding components.
Open AccessLow-Temperature Thermomechanical Consolidation of Aluminosilicate Sorbents Impregnated with Model Oil-Containing Radioactive Waste
This paper investigates the possibility of pressure-assisted thermomechanical consolidation and thermal treatment without applied pressure during the low-temperature consolidation of oil-saturated aluminosilicate sorbents for their subsequent application in the conditioning of liquid oil-containing radioactive waste (RAW). The Premium and Absorbent sorbents saturated with transformer oil not containing radionuclides were used as model RAW systems. It was established that pressure-assisted thermomechanical consolidation leads to the formation of a denser structure and a reduction in hydrocarbon-phase losses compared with thermal treatment without applied pressure. For Premium, mass losses decreased from 0.74 to 0.35 g (by 53%), and for Absorbent, from 0.75 to 0.47 g (by 37%), and the consolidated samples were characterized by a more homogeneous microstructure and increased resistance to exudation. It was established that the efficiency of hydrocarbon-phase retention is determined by both the treatment conditions and the mineral composition of the sorbent. The obtained results indicate the prospects of low-temperature pressure-assisted thermomechanical consolidation at a temperature of 150 °C, a pressure of 1.5 MPa, and a holding time of 20 s for the conditioning of oil-containing RAW without the use of additional binding components.
- Open Access
Microstructure Evolution and Phase Stability of ODS Steel During Spark Plasma Sintering
The effect of spark plasma sintering (SPS) temperature on the structural and phase state and the physicomechanical properties of an ODS steel based on the Fe-Cr-Y2O3 system was investigated. It was established that increasing the SPS temperature is accompanied by a gradual increase in the degree of consolidation and a reduction in residual porosity. At 1400 °C, the densest and most homogeneous microstructure is formed, and the relative density reaches 96.3%. Further increasing the temperature to 1500 °C has little effect on the degree of consolidation, while the main phase composition, α-Fe(Cr), is retained. According to X-ray diffraction analysis, the crystallite size increases with increasing temperature, whereas the lattice microstrain decreases up to 1400 °C and increases at 1500 °C. The microhardness ranges from 489.4 to 588.7 HV1, reaching a maximum value of 588.7 HV1 at 1500 °C. Based on the combined consolidation and microstructural characteristics, 1400 °C was identified as the optimal SPS temperature, providing the highest degree of densification and the most homogeneous structural state of the material. The results demonstrate that, after a high degree of consolidation has been achieved, further increasing the temperature primarily promotes structural evolution without a significant increase in material density.
Open AccessMicrostructure Evolution and Phase Stability of ODS Steel During Spark Plasma Sintering
The effect of spark plasma sintering (SPS) temperature on the structural and phase state and the physicomechanical properties of an ODS steel based on the Fe-Cr-Y2O3 system was investigated. It was established that increasing the SPS temperature is accompanied by a gradual increase in the degree of consolidation and a reduction in residual porosity. At 1400 °C, the densest and most homogeneous microstructure is formed, and the relative density reaches 96.3%. Further increasing the temperature to 1500 °C has little effect on the degree of consolidation, while the main phase composition, α-Fe(Cr), is retained. According to X-ray diffraction analysis, the crystallite size increases with increasing temperature, whereas the lattice microstrain decreases up to 1400 °C and increases at 1500 °C. The microhardness ranges from 489.4 to 588.7 HV1, reaching a maximum value of 588.7 HV1 at 1500 °C. Based on the combined consolidation and microstructural characteristics, 1400 °C was identified as the optimal SPS temperature, providing the highest degree of densification and the most homogeneous structural state of the material. The results demonstrate that, after a high degree of consolidation has been achieved, further increasing the temperature primarily promotes structural evolution without a significant increase in material density.
- Open Access
- 3 June 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (6) , 305
Effect of Mineral Additives on Cement Matrices Intended for Radioactive Waste Immobilization
This study investigates the effect of mineral additives of different natures, namely blast-furnace slag, fly ash, and bentonite, on structure formation, phase composition, microstructure, and physicomechanical properties of cement matrices. The analysis included measurements of mass change and linear shrinkage during hardening, determination of density and microhardness, X-ray phase analysis, and microstructural examination by scanning electron microscopy. It was found that the introduction of mineral additives reduced linear shrinkage from 6.06 mm for the control composition to 0.25 mm for the composition with blast-furnace slag, 2.31 mm for the composition with fly ash, and 1.01 mm for the composition with bentonite. The maximum density and microhardness values were obtained for the matrix with blast-furnace slag and amounted to 1.99 ± 0.03 g/cm3 and 39.95 ± 1.12 HV1, respectively, whereas the overall range of values for the investigated compositions was 1.52–1.99 g/cm3 and 30.2–39.95 HV1. X-ray phase analysis showed that the amorphous component varied from 61 to 78%, reaching its maximum value in the composition with blast-furnace slag, which is associated with the formation of poorly crystalline C–S–H and aluminosilicate phases. According to the SEM data, the average size of visible pore-like defects was 2.4 μm for the control composition, 1.4 μm for the composition with blast-furnace slag, 1.3 μm for the composition with fly ash, and 1.7 μm for the composition with bentonite. The most favorable combination of high density, microhardness, developed amorphous component, and homogeneous microstructure was established for the composition with blast-furnace slag. The obtained results can be used as a materials-science basis for the development of cement matrices intended for further studies on the immobilization of solid radioactive waste.
- 3 June 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (6) , 305
Open AccessEffect of Mineral Additives on Cement Matrices Intended for Radioactive Waste Immobilization
This study investigates the effect of mineral additives of different natures, namely blast-furnace slag, fly ash, and bentonite, on structure formation, phase composition, microstructure, and physicomechanical properties of cement matrices. The analysis included measurements of mass change and linear shrinkage during hardening, determination of density and microhardness, X-ray phase analysis, and microstructural examination by scanning electron microscopy. It was found that the introduction of mineral additives reduced linear shrinkage from 6.06 mm for the control composition to 0.25 mm for the composition with blast-furnace slag, 2.31 mm for the composition with fly ash, and 1.01 mm for the composition with bentonite. The maximum density and microhardness values were obtained for the matrix with blast-furnace slag and amounted to 1.99 ± 0.03 g/cm3 and 39.95 ± 1.12 HV1, respectively, whereas the overall range of values for the investigated compositions was 1.52–1.99 g/cm3 and 30.2–39.95 HV1. X-ray phase analysis showed that the amorphous component varied from 61 to 78%, reaching its maximum value in the composition with blast-furnace slag, which is associated with the formation of poorly crystalline C–S–H and aluminosilicate phases. According to the SEM data, the average size of visible pore-like defects was 2.4 μm for the control composition, 1.4 μm for the composition with blast-furnace slag, 1.3 μm for the composition with fly ash, and 1.7 μm for the composition with bentonite. The most favorable combination of high density, microhardness, developed amorphous component, and homogeneous microstructure was established for the composition with blast-furnace slag. The obtained results can be used as a materials-science basis for the development of cement matrices intended for further studies on the immobilization of solid radioactive waste.
- 8 December 2025
- Published by Republican State Enterprise "National Nuclear Center of the Republic of Kazakhstan" in NNC RK Bulletin
- No. 4
PLASMA-CHEMICAL SYNTHESIS OF CARBON FROM METHANE IN A MICROWAVE DISCHARGE
This study presents a comprehensive investigation of carbon materials synthesized via methane pyrolysis in a microwave plasma discharge under atmospheric pressure. Particular attention is paid to the influence of microwave power on the morphological, phase, and textural characteristics of the resulting carbon. Scanning electron microscopy (SEM) revealed that increasing the discharge power from 0.6 to 1.4 kW leads to a reduction in average particle size (from ~20.2 to ~10.4 μm) and the formation of more dispersed structures. X-ray diffraction (XRD) analysis showed a transition from a turbostratic, amorphous phase to a more ordered, graphite-like structure with increasing process temperature. Nitrogen adsorption analysis using the BET and BJH methods confirmed the mesoporous nature of the materials, with the highest specific surface area and pore volume observed at the lowest plasma power (628 m 2 /g and 5.04 cm 3 /g, respectively). These findings demonstrate that microwave discharge power is a key parameter for tailoring the structure and functionality of carbon materials, making them promising candidates for applications in catalysis, adsorption, and energy storage.
- 8 December 2025
- Published by Republican State Enterprise "National Nuclear Center of the Republic of Kazakhstan" in NNC RK Bulletin
- No. 4
PLASMA-CHEMICAL SYNTHESIS OF CARBON FROM METHANE IN A MICROWAVE DISCHARGE
This study presents a comprehensive investigation of carbon materials synthesized via methane pyrolysis in a microwave plasma discharge under atmospheric pressure. Particular attention is paid to the influence of microwave power on the morphological, phase, and textural characteristics of the resulting carbon. Scanning electron microscopy (SEM) revealed that increasing the discharge power from 0.6 to 1.4 kW leads to a reduction in average particle size (from ~20.2 to ~10.4 μm) and the formation of more dispersed structures. X-ray diffraction (XRD) analysis showed a transition from a turbostratic, amorphous phase to a more ordered, graphite-like structure with increasing process temperature. Nitrogen adsorption analysis using the BET and BJH methods confirmed the mesoporous nature of the materials, with the highest specific surface area and pore volume observed at the lowest plasma power (628 m 2 /g and 5.04 cm 3 /g, respectively). These findings demonstrate that microwave discharge power is a key parameter for tailoring the structure and functionality of carbon materials, making them promising candidates for applications in catalysis, adsorption, and energy storage.
- Open Access
Structural and Phase Characteristics of LaNi5-Based Materials Modified with Ti, Mn, and Co
In this work, the results of the structural and phase state of LaNi5-based alloys modified with Ti, Mn, and Co elements, obtained by mechanical alloying and subsequent spark plasma sintering, are presented. X-ray diffraction analysis was carried out to determine the phase composition, lattice parameters, microstrain, and average crystallite size, as well as to study the morphology and microstructure of the synthesized samples. It was established that the ball-to-powder ratio (BPR) and the milling speed affect the degree of intermetallic phase formation and the level of accumulated microstrains. The optimal mechanical alloying parameters make it possible to form the necessary precursor components for subsequent spark plasma sintering (SPS). It was determined that the SPS process effectively promotes the formation of intermetallic phases such as TiNi, LaNi4Mn, LaNi3Mn2, and LaNi4Co, ensuring high crystallinity and a reduction in defects accumulated during mechanical alloying. The morphology and microstructure of the samples with titanium, manganese, and cobalt additions showed that at the mechanical alloying stage, all systems are characterized by a dispersed and agglomerated structure, a wide particle size distribution, and a developed surface. After SPS, all series exhibited material consolidation and the formation of a dense matrix with distinct grain boundaries.
Open AccessStructural and Phase Characteristics of LaNi5-Based Materials Modified with Ti, Mn, and Co
In this work, the results of the structural and phase state of LaNi5-based alloys modified with Ti, Mn, and Co elements, obtained by mechanical alloying and subsequent spark plasma sintering, are presented. X-ray diffraction analysis was carried out to determine the phase composition, lattice parameters, microstrain, and average crystallite size, as well as to study the morphology and microstructure of the synthesized samples. It was established that the ball-to-powder ratio (BPR) and the milling speed affect the degree of intermetallic phase formation and the level of accumulated microstrains. The optimal mechanical alloying parameters make it possible to form the necessary precursor components for subsequent spark plasma sintering (SPS). It was determined that the SPS process effectively promotes the formation of intermetallic phases such as TiNi, LaNi4Mn, LaNi3Mn2, and LaNi4Co, ensuring high crystallinity and a reduction in defects accumulated during mechanical alloying. The morphology and microstructure of the samples with titanium, manganese, and cobalt additions showed that at the mechanical alloying stage, all systems are characterized by a dispersed and agglomerated structure, a wide particle size distribution, and a developed surface. After SPS, all series exhibited material consolidation and the formation of a dense matrix with distinct grain boundaries.
- Open Access
Dispersion of Sintered Mg-Ni-Ce Materials for Efficient Hydrogen Storage
This paper presents the results of the effect of dispersion on the structural-phase state of the material for hydrogen storage of the Mg-Ni-Ce system. X-ray phase analysis and scanning electron microscopy studies have shown that the sequential use of mechanical synthesis and spark-plasma sintering methods ensures the formation of a stable and dense microstructure with a high content of the intermetallic phase Mg2Ni. As a result of dispersion for 1 h, the sintered material was transferred to a finely dispersed state without changing the phase composition. Increasing the duration of dispersion to 2 h led to the formation of large agglomerates and the destruction of the material structure. For the first time, the dispersion technology was applied to materials of the Mg-Ni-Ce system, pre-sintered by spark-plasma sintering.
Open AccessDispersion of Sintered Mg-Ni-Ce Materials for Efficient Hydrogen Storage
This paper presents the results of the effect of dispersion on the structural-phase state of the material for hydrogen storage of the Mg-Ni-Ce system. X-ray phase analysis and scanning electron microscopy studies have shown that the sequential use of mechanical synthesis and spark-plasma sintering methods ensures the formation of a stable and dense microstructure with a high content of the intermetallic phase Mg2Ni. As a result of dispersion for 1 h, the sintered material was transferred to a finely dispersed state without changing the phase composition. Increasing the duration of dispersion to 2 h led to the formation of large agglomerates and the destruction of the material structure. For the first time, the dispersion technology was applied to materials of the Mg-Ni-Ce system, pre-sintered by spark-plasma sintering.
- Open Access
Evolution of Phase Transformations in the Mg-Ni-Ce System After Mechanical Synthesis and Spark Plasma Sintering
The present study focuses on investigating the evolution of phase transformations in the Mg-Ni-Ce system under the influence of mechanical synthesis (MS) and spark plasma sintering (SPS). Magnesium powder mixtures with different nickel and cerium contents (Mg-3%Ni-2%Ce, Mg-7%Ni-3%Ce, and Mg-10%Ni-5%Ce) were mechanically activated along with various grinding parameters. The X-ray phase analysis (XRD) has shown the successive stages of the phase formation in the MS process: from the initial components to the formation of intermetallic compounds of Mg2Ni, Mg12Ni6, and CeMg3. An increase in the intensity of mechanical treatment facilitated the accelerated destruction of the crystal lattice, the generation of defects, and the formation of new phases, as evidenced by the broadening and reduction in the intensity of Mg diffraction peaks. The subsequent SPS stage promoted the completion of phase transformations, structural stabilization, and the formation of a dense, multicomponent microstructure with a uniform distribution of intermetallic compounds. The observed average crystallite sizes ranged from 20 to 70 nm, depending on the processing conditions. The research results demonstrate the possibility of targeted control over the phase composition, opening new opportunities for the development of highly efficient hydrogen-absorbing alloys.
Open AccessEvolution of Phase Transformations in the Mg-Ni-Ce System After Mechanical Synthesis and Spark Plasma Sintering
The present study focuses on investigating the evolution of phase transformations in the Mg-Ni-Ce system under the influence of mechanical synthesis (MS) and spark plasma sintering (SPS). Magnesium powder mixtures with different nickel and cerium contents (Mg-3%Ni-2%Ce, Mg-7%Ni-3%Ce, and Mg-10%Ni-5%Ce) were mechanically activated along with various grinding parameters. The X-ray phase analysis (XRD) has shown the successive stages of the phase formation in the MS process: from the initial components to the formation of intermetallic compounds of Mg2Ni, Mg12Ni6, and CeMg3. An increase in the intensity of mechanical treatment facilitated the accelerated destruction of the crystal lattice, the generation of defects, and the formation of new phases, as evidenced by the broadening and reduction in the intensity of Mg diffraction peaks. The subsequent SPS stage promoted the completion of phase transformations, structural stabilization, and the formation of a dense, multicomponent microstructure with a uniform distribution of intermetallic compounds. The observed average crystallite sizes ranged from 20 to 70 nm, depending on the processing conditions. The research results demonstrate the possibility of targeted control over the phase composition, opening new opportunities for the development of highly efficient hydrogen-absorbing alloys.
- 1 April 2025
- Published by Republican State Enterprise "National Nuclear Center of the Republic of Kazakhstan" in NNC RK Bulletin
- No. 1
EVALUATION OF THE EFFECT OF MECHANOSYNTHESIS PARAMETERS ON THE MORPHOLOGY OF A MAGNESIUM-BASED POWDER COMPOSITION
This article presents an analysis of the dependence of phase and morphological changes in the powder composition of the Mg-Ni-Ce system on the parameters of mechanical synthesis. During the mechanical synthesis process, it was found that, in addition to acceleration and duration parameters, the ratio of powder to milling balls has a significant influence on changes in the structural characteristics of the material. The results of the microscopic analysis showed that with a powderto-ball ratio of 1:10, the average particle size in the synthesized mixtures is 13.76 µm. At the same time, when applying a ratio of 1:30, the particle size decreases to 7.59 µm. It was established that magnesium is the primary phase in all samples. However, at a ratio of 1:30, the formation of the hexagonal crystal lattice of the MgNi phase and the emergence of the CeNi phase are identified.
- 1 April 2025
- Published by Republican State Enterprise "National Nuclear Center of the Republic of Kazakhstan" in NNC RK Bulletin
- No. 1
EVALUATION OF THE EFFECT OF MECHANOSYNTHESIS PARAMETERS ON THE MORPHOLOGY OF A MAGNESIUM-BASED POWDER COMPOSITION
This article presents an analysis of the dependence of phase and morphological changes in the powder composition of the Mg-Ni-Ce system on the parameters of mechanical synthesis. During the mechanical synthesis process, it was found that, in addition to acceleration and duration parameters, the ratio of powder to milling balls has a significant influence on changes in the structural characteristics of the material. The results of the microscopic analysis showed that with a powderto-ball ratio of 1:10, the average particle size in the synthesized mixtures is 13.76 µm. At the same time, when applying a ratio of 1:30, the particle size decreases to 7.59 µm. It was established that magnesium is the primary phase in all samples. However, at a ratio of 1:30, the formation of the hexagonal crystal lattice of the MgNi phase and the emergence of the CeNi phase are identified.