Matteo Majer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Matteo Majer has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Matteo Pini
Propulsion & Power, Faculty of Aerospace Engineering, Delft University of Technology, 2628 CD Delft, The Netherlands
2 shared publications - Adam Joseph Head
Delft University of Technology
1 shared publication - Diogo S. C. Fernandes
Delft University of Technology
1 shared publication - Edoardo Gheller
Department of Mechanical Engineering, Politecnico di Milano , Via G. la Masa 1 , Milan 20156, Italy
1 shared publication - Ludovico Dassi
Dept. of Mech. Eng. - Politecnico di Milano
1 shared publication - Paolo Pennacchi
Department of Mechanical Engineering, Politecnico di Milano, Via G. La Masa 1, 20156 Milan, Italy
1 shared publication
Latest Publications
- 15 October 2025
- Published by Springer Nature
- p. 61-70
Towards a Thermodynamic Validation Map for Non-Ideal Compressible Flows
- 15 October 2025
- Published by Springer Nature
- p. 61-70
Towards a Thermodynamic Validation Map for Non-Ideal Compressible Flows
- Open Access
- 22 May 2025
- Published by Global Power and Propulsion Society in Journal of the Global Power and Propulsion Society
- Vol. 9 (May) , 45-66
Mechanical design and rotordynamic analysis of the ORCHID turbine
The ORCHID turbine is a laboratory single-stage 10 kW high-speed (∼100 krpm) radial-inflow turbine for high-temperature/high-efficiency organic Rankine cycle (ORC) systems, designed at the Aerospace Propulsion and Power laboratory of Delft University of Technology. It will be installed within a test section of the organic Rankine cycle hybrid integrated device (ORCHID) facility, the setup for fundamental and applied studies on ORC technology currently in operation in the same lab. Experimental data from future measurement campaigns will be employed to validate design and performance prediction tools and to develop best practices for operating these unconventional machines, whose most notable features are the ultra-high expansion ratio (>40), highly supersonic flow in the stator (Ma > 2), and the large flow deflection within the impeller channels (>90). This article presents the mechanical design and the rotordynamic assessment of the ORCHID turbine rotor, and best practices for the numerical evaluation of the rotordynamic characteristics and stability of high-speed ORC turbine rotors. The emphasis is on three main aspects: i) the modeling and quantification of the damping characteristics of a squeeze film damper (SFD) cartridge for the selected turbocharger ball bearings supporting the turbine shaft; ii) the characterization of the stiffness and damping coefficients of a custom designed pocket gas seal, performed using 3D RANS simulations; iii) the analysis of linear elastic rotordynamic simulations using a finite beam element model of the turbine rotor. Results of the rotordynamic simulations show that the rotor would operate in the sub-critical regime with respect to the first bending mode. The influence of model parameters such as the rotor eccentricity and the orbit radius was included in the analysis by conducting a parametric study of the SFD fluid forces. The Campbell diagrams show that shaft bending frequencies are significantly affected by changes in the SFD dynamic response depending on the rotational speed. The influence of the stiffness of rolling bearing elements and of the destabilizing forces due to the impeller and gas seal cross-coupled stiffness was also evaluated. The rigidity of the rolling elements slightly affects the shaft bending mode, while large values of the destabilizing forces cause a rotordynamic instability of the first rigid mode.
- 22 May 2025
- Published by Global Power and Propulsion Society in Journal of the Global Power and Propulsion Society
- Vol. 9 (May) , 45-66
Open AccessMechanical design and rotordynamic analysis of the ORCHID turbine
The ORCHID turbine is a laboratory single-stage 10 kW high-speed (∼100 krpm) radial-inflow turbine for high-temperature/high-efficiency organic Rankine cycle (ORC) systems, designed at the Aerospace Propulsion and Power laboratory of Delft University of Technology. It will be installed within a test section of the organic Rankine cycle hybrid integrated device (ORCHID) facility, the setup for fundamental and applied studies on ORC technology currently in operation in the same lab. Experimental data from future measurement campaigns will be employed to validate design and performance prediction tools and to develop best practices for operating these unconventional machines, whose most notable features are the ultra-high expansion ratio (>40), highly supersonic flow in the stator (Ma > 2), and the large flow deflection within the impeller channels (>90). This article presents the mechanical design and the rotordynamic assessment of the ORCHID turbine rotor, and best practices for the numerical evaluation of the rotordynamic characteristics and stability of high-speed ORC turbine rotors. The emphasis is on three main aspects: i) the modeling and quantification of the damping characteristics of a squeeze film damper (SFD) cartridge for the selected turbocharger ball bearings supporting the turbine shaft; ii) the characterization of the stiffness and damping coefficients of a custom designed pocket gas seal, performed using 3D RANS simulations; iii) the analysis of linear elastic rotordynamic simulations using a finite beam element model of the turbine rotor. Results of the rotordynamic simulations show that the rotor would operate in the sub-critical regime with respect to the first bending mode. The influence of model parameters such as the rotor eccentricity and the orbit radius was included in the analysis by conducting a parametric study of the SFD fluid forces. The Campbell diagrams show that shaft bending frequencies are significantly affected by changes in the SFD dynamic response depending on the rotational speed. The influence of the stiffness of rolling bearing elements and of the destabilizing forces due to the impeller and gas seal cross-coupled stiffness was also evaluated. The rigidity of the rolling elements slightly affects the shaft bending mode, while large values of the destabilizing forces cause a rotordynamic instability of the first rigid mode.
- Open Access
- 11 April 2025
- Published by Global Power and Propulsion Society in Journal of the Global Power and Propulsion Society
- Vol. 9, 19-46
Design guidelines for high-pressure ratio supersonic radial-inflow turbines of organic rankine cycle systems
The radial-inflow turbine (RIT) is a widely adopted turbo-expander in power and propulsion systems of low-to-medium power capacity due to its high efficiency and compactness. Compared to conventional radial turbines for gas turbines and air cycle machines, the design of expanders for high-temperature organic Rankine cycle power systems involves additional challenges, as these machines operate with very high expansion or volumetric flow ratio and partly or entirely in the nonideal compressible fluid dynamic regime. This study examines the impact of the working fluid, of the volumetric flow ratio, and of the nonideal thermodynamic effects on the design guidelines for RIT. To this purpose, a reduced-order modeling framework for turbine fluid-dynamic design encompassing a loss model based on first principles is developed and verified against results from uRANS. Results highlighted that at the geometrical scale of interest the impact of the working fluid molecular complexity on the efficiency is marginal. Moreover, it is shown that the average isentropic pressure-volume exponent (γ¯Pv) can be used to predict the magnitude of nonideal thermodynamic effects on the stage efficiency, whose variation depends on the value of the volumetric flow ratio and of the work and flow coefficients. Design guidelines that can be used for preliminary turbine design in system-level calculations are presented in graphical form, and illustrate the relation between the optimal set of stage duty coefficients, i.e., the work and flow coefficients that maximize the efficiency, the stage efficiency, the volumetric flow ratio, and the similarity parameter γ¯Pv.
- 11 April 2025
- Published by Global Power and Propulsion Society in Journal of the Global Power and Propulsion Society
- Vol. 9, 19-46
Open AccessDesign guidelines for high-pressure ratio supersonic radial-inflow turbines of organic rankine cycle systems
The radial-inflow turbine (RIT) is a widely adopted turbo-expander in power and propulsion systems of low-to-medium power capacity due to its high efficiency and compactness. Compared to conventional radial turbines for gas turbines and air cycle machines, the design of expanders for high-temperature organic Rankine cycle power systems involves additional challenges, as these machines operate with very high expansion or volumetric flow ratio and partly or entirely in the nonideal compressible fluid dynamic regime. This study examines the impact of the working fluid, of the volumetric flow ratio, and of the nonideal thermodynamic effects on the design guidelines for RIT. To this purpose, a reduced-order modeling framework for turbine fluid-dynamic design encompassing a loss model based on first principles is developed and verified against results from uRANS. Results highlighted that at the geometrical scale of interest the impact of the working fluid molecular complexity on the efficiency is marginal. Moreover, it is shown that the average isentropic pressure-volume exponent (γ¯Pv) can be used to predict the magnitude of nonideal thermodynamic effects on the stage efficiency, whose variation depends on the value of the volumetric flow ratio and of the work and flow coefficients. Design guidelines that can be used for preliminary turbine design in system-level calculations are presented in graphical form, and illustrate the relation between the optimal set of stage duty coefficients, i.e., the work and flow coefficients that maximize the efficiency, the stage efficiency, the volumetric flow ratio, and the similarity parameter γ¯Pv.