Sitian Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Sitian Wu has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Weiqian Wang
School of Instrumentation and Optoelectronic Engineering, Beihang University, Beijing, China
2 shared publications - Xiangyang Zhou
Beihang University
2 shared publications Jinguo Mu
School of Instrumentation and Optoelectronic Engineering, Beihang University, Beijing, China
1 shared publication- Jinguo Mu
Beihang University
1 shared publication - Pei Nie
School of Instrumentation and Optoelectronic Engineering, Institute of Large-Scale Scientific Facility and Center for Zero Magnetic Field Science, Beihang University, Beijing, China
1 shared publication Si Zhu
School of Instrumentation and Optoelectronic Engineering, Beihang University, Beijing, China
1 shared publication
Latest Publications
- 20 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-13
Design of Uniform Magnetic Field Coil for Miniaturized Atomic Sensors Considering the Thermal Effect
This article proposes a design method based on a multi-objective optimization strategy considering the thermal effect for uniform magnetic field coil (UMFC), which is used to provide working magnetic fields for miniaturized atomic sensors and compensate for stray magnetic fields generated by environment and interior components of sensor. With the volume reduction of atomic sensors, the uniformity and thermal effects of UMFC will decrease and increase, respectively, which is detrimental to the performance of the sensor. Therefore, to improve the magnetic field uniformity of UMFC and reduce heat generation, an optimized target field method combining nondominated sorting genetic algorithm III (NSGA-III) is proposed, in which the uniformity error function and thermal power function of the UMFC is taken as design objectives. The experimental results show that the uniformity and temperature of the coil designed by the proposed method are 0.0432% and 316.5 K, respectively, which are of high performance and meet the operation requirement the atomic sensor.
- 20 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-13
Design of Uniform Magnetic Field Coil for Miniaturized Atomic Sensors Considering the Thermal Effect
This article proposes a design method based on a multi-objective optimization strategy considering the thermal effect for uniform magnetic field coil (UMFC), which is used to provide working magnetic fields for miniaturized atomic sensors and compensate for stray magnetic fields generated by environment and interior components of sensor. With the volume reduction of atomic sensors, the uniformity and thermal effects of UMFC will decrease and increase, respectively, which is detrimental to the performance of the sensor. Therefore, to improve the magnetic field uniformity of UMFC and reduce heat generation, an optimized target field method combining nondominated sorting genetic algorithm III (NSGA-III) is proposed, in which the uniformity error function and thermal power function of the UMFC is taken as design objectives. The experimental results show that the uniformity and temperature of the coil designed by the proposed method are 0.0432% and 316.5 K, respectively, which are of high performance and meet the operation requirement the atomic sensor.
- 25 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (11) , 18962-18970
Design of Transparent Nonmagnetic Electric Heating Film Based on MEMS Technology for Microalkali Metal Vapor Cell
Aiming to address the limitations of traditional heating films in balancing magnetic field suppression and uniform heating in spin exchange relaxation free (SERF) atomic magnetometer applications, this paper designs a transparent, non-magnetic electric heating film based on MEMS technology, in which indium tin oxide is used as the core heating material. First, a model is developed to analyze the spatial magnetic field strength induced by current flowing in different directions through the wiring. The layout design of the heating film is then optimized through quantitative analysis and simulation. Next, ITO, a transparent material, is selected and processed using MEMS technology. This successfully addresses the condensation issue at the optical apertures of traditional flexible printed circuit (FPC) heating films, which is caused by uneven heating, thereby improving heating uniformity. The final experiment validated the feasibility and effectiveness of the design. The experimental results show that the magnetic flux density of the designed heating film under DC conditions is 0.8154 nT/mA. Under the same heating conditions, the temperature variance in the vapor cell area decreased from 0.0125°C2 for traditional heating films to 0.0103°C2, with a particularly significant temperature increase observed in the optical aperture region. Experimental data confirm that the MEMS-based transparent heating film developed in this study demonstrates significant advantages in both magnetic field suppression and heating uniformity.
- 25 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (11) , 18962-18970
Design of Transparent Nonmagnetic Electric Heating Film Based on MEMS Technology for Microalkali Metal Vapor Cell
Aiming to address the limitations of traditional heating films in balancing magnetic field suppression and uniform heating in spin exchange relaxation free (SERF) atomic magnetometer applications, this paper designs a transparent, non-magnetic electric heating film based on MEMS technology, in which indium tin oxide is used as the core heating material. First, a model is developed to analyze the spatial magnetic field strength induced by current flowing in different directions through the wiring. The layout design of the heating film is then optimized through quantitative analysis and simulation. Next, ITO, a transparent material, is selected and processed using MEMS technology. This successfully addresses the condensation issue at the optical apertures of traditional flexible printed circuit (FPC) heating films, which is caused by uneven heating, thereby improving heating uniformity. The final experiment validated the feasibility and effectiveness of the design. The experimental results show that the magnetic flux density of the designed heating film under DC conditions is 0.8154 nT/mA. Under the same heating conditions, the temperature variance in the vapor cell area decreased from 0.0125°C2 for traditional heating films to 0.0103°C2, with a particularly significant temperature increase observed in the optical aperture region. Experimental data confirm that the MEMS-based transparent heating film developed in this study demonstrates significant advantages in both magnetic field suppression and heating uniformity.