Jianjing Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jianjing Wang has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Chaoyang Zhou
School of Metallurgical Engineering, Jiangsu University of Science and Technology, Zhangjiagang 215600, China
1 shared publication H Yu
University of Science and Technology Beijing, China
1 shared publication- Houxin Wang
CITIC Metal Co., Ltd., Beijing 100004, China
1 shared publication - Jiangbo Deng
Key Lab of New Processing Technology for Nonferrous Metals and Materials, Ministry of Education, Guilin University of Technology, Guilin 541004, China
1 shared publication - Meiqiao Wu
Key Lab of New Processing Technology for Nonferrous Metals and Materials, Ministry of Education, Guilin University of Technology, Guilin 541004, China
1 shared publication - Xinbin Liu
School of Intelligent Manufacturing and Mechanical Engineering, Hunan Institute of Technology, Hengyang 421002, China
1 shared publication
Latest Publications
- Open Access
Effect of Nb Content on Strength and Toughness of 25MnB Crawler Steel and Its Microstructural Characterization
To address the failure of 25MnB crawler track steel due to insufficient strength and toughness, this study designed a new type of 25MnB crawler track steel and investigated the effects of the Nb content on its mechanical properties, microstructure, dislocation evolution, and precipitation behavior. The experimental results show that, compared to 25MnB steel without Nb, the addition of 0.03% Nb significantly increased the yield strength of the experimental steel to 1450 MPa, with an elongation rate of 15.9%. The room-temperature impact energy showed a slight improvement, while the low-temperature impact absorption energy improved notably, reaching 36 J at −40 °C. The microstructural characterization and analysis revealed that increasing the Nb content refined the effective grain size of prior austenite and martensite. The (Nb, Ti)C precipitates provided a higher precipitation driving force, promoting the formation of precipitates and increasing the average dislocation density. Additionally, the increased proportion of high-angle grain boundaries (HAGBs) enabled grain boundaries and precipitates to jointly hinder crack propagation. This study demonstrates that Nb-Ti microalloying can effectively enhance the strength, toughness, and plasticity of track steel, demonstrating promising application prospects.
Open AccessEffect of Nb Content on Strength and Toughness of 25MnB Crawler Steel and Its Microstructural Characterization
To address the failure of 25MnB crawler track steel due to insufficient strength and toughness, this study designed a new type of 25MnB crawler track steel and investigated the effects of the Nb content on its mechanical properties, microstructure, dislocation evolution, and precipitation behavior. The experimental results show that, compared to 25MnB steel without Nb, the addition of 0.03% Nb significantly increased the yield strength of the experimental steel to 1450 MPa, with an elongation rate of 15.9%. The room-temperature impact energy showed a slight improvement, while the low-temperature impact absorption energy improved notably, reaching 36 J at −40 °C. The microstructural characterization and analysis revealed that increasing the Nb content refined the effective grain size of prior austenite and martensite. The (Nb, Ti)C precipitates provided a higher precipitation driving force, promoting the formation of precipitates and increasing the average dislocation density. Additionally, the increased proportion of high-angle grain boundaries (HAGBs) enabled grain boundaries and precipitates to jointly hinder crack propagation. This study demonstrates that Nb-Ti microalloying can effectively enhance the strength, toughness, and plasticity of track steel, demonstrating promising application prospects.
- Open Access
- 1 November 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 668 (1) , 012027
Constitutive modeling of dynamic recrystallization and precipitation behavior of Nb and Ti of Q1030 high strength steel
The thermal deformation and precipitation behavior at 900-1100° and strain rate of 0.1-5s−1 were studied by Gleeble-3800 thermal simulator of Q1030 high strength steel. The activation energy of hot deformation in austenite region was determined by regression method, and the hot deformation equation of the Q1030 high strength steel was established. The critical strain and peak strain of dynamic recrystallization were predicted accurately by fitting the inflection point with cubic polynomial of curve of Q1030 high strength steel, and relationship between critical strain and Z parameter was established. Finally, the precipitation behavior of Nb and Ti particles during low strain rate deformation was studied, the results show that the precipitated phases in steel are rectangular TiN, quadratic (Nb, Ti) (C, N) carbonitride, elliptical (Nb, Ti) C carbide and NbC. Thermodynamic calculation shows that the order of precipitation of the second phase in steel is TiN, TiC, NbC and NbN.
- 1 November 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 668 (1) , 012027
Open AccessConstitutive modeling of dynamic recrystallization and precipitation behavior of Nb and Ti of Q1030 high strength steel
The thermal deformation and precipitation behavior at 900-1100° and strain rate of 0.1-5s−1 were studied by Gleeble-3800 thermal simulator of Q1030 high strength steel. The activation energy of hot deformation in austenite region was determined by regression method, and the hot deformation equation of the Q1030 high strength steel was established. The critical strain and peak strain of dynamic recrystallization were predicted accurately by fitting the inflection point with cubic polynomial of curve of Q1030 high strength steel, and relationship between critical strain and Z parameter was established. Finally, the precipitation behavior of Nb and Ti particles during low strain rate deformation was studied, the results show that the precipitated phases in steel are rectangular TiN, quadratic (Nb, Ti) (C, N) carbonitride, elliptical (Nb, Ti) C carbide and NbC. Thermodynamic calculation shows that the order of precipitation of the second phase in steel is TiN, TiC, NbC and NbN.