Suresh Kumar Pittala
Suresh Kumar Pittala has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Muralidharan J
KPR Institute of Engineering and Technology
2 shared publications A. Jerrin Simla
Department of Computer Science and Engineering, Saveetha School of Engineering, Saveetha Institute of Medical and Technical Sciences Saveetha University Chennai India
1 shared publicationC. Arunabala
Ananthalakshmi Institute of Technology and Sciences
1 shared publication- Dama Anand
Koneru Lakshmaiah Education Foundation
1 shared publication L. Megalan Leo
Department of ECE Sathyabama Institute of Engineering and Technology Chennai Tamilnadu India
1 shared publication- Narendra Kumar
Amity University Jharkhand
1 shared publication
Latest Publications
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (19) , 28380-28386
Polyhistidine-Functionalized Ti–V–N Nanorod Interfaces for High-Sensitivity Solid-State pH Sensing: Mechanism and Stability Assessment
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (19) , 28380-28386
Polyhistidine-Functionalized Ti–V–N Nanorod Interfaces for High-Sensitivity Solid-State pH Sensing: Mechanism and Stability Assessment
- 23 April 2025
- Published by Wiley in International Journal of Communication Systems
- Vol. 38 (9)
A Novel Optimal Sampling Digital PLL Design With High Performance and Alleviated Hardware for IOT Applications
A key component of Internet of Things (IoT) nodes is the phase‐locked loop (PLL), yet power distribution remains an issue with the digital versions of these nodes. Reducing the high‐power distribution, which usually regulates the all‐digital PLL (ADPLL) power close to the digitally controlled oscillator (DCO), is essential for the development of the ultra‐low‐power ADPLL. The low‐level audio will reduce the active signal‐to‐noise ratio (SNR), when ADPLL is used in a communications system, causing significant inaccuracy and reducing the data rate. Therefore, it is vital to understand the trade‐off between phase noise, lock time performance, and variability in ADPLL. We present the improved design optimal sampling digital PLL (OS‐DPLL) for IoT applications in this paper. The proposed OS‐DPLL consists of a loop module (LM), ring oscillator (RO), first‐order digital loop filter (F‐DLF), divider chain, and bang–bang phase frequency detector (BBPFD), which uses the improved bang–bang approach. In addition, an efficient operating system is introduced to isolated operating modes, which provide standard bandwidth performance for sound and spectral purity in a closed phase mode. The simulation result determines the effectiveness of the proposed OS‐DPLL design based on power consumption, hardware utilization, and throughput.
- 23 April 2025
- Published by Wiley in International Journal of Communication Systems
- Vol. 38 (9)
A Novel Optimal Sampling Digital PLL Design With High Performance and Alleviated Hardware for IOT Applications
A key component of Internet of Things (IoT) nodes is the phase‐locked loop (PLL), yet power distribution remains an issue with the digital versions of these nodes. Reducing the high‐power distribution, which usually regulates the all‐digital PLL (ADPLL) power close to the digitally controlled oscillator (DCO), is essential for the development of the ultra‐low‐power ADPLL. The low‐level audio will reduce the active signal‐to‐noise ratio (SNR), when ADPLL is used in a communications system, causing significant inaccuracy and reducing the data rate. Therefore, it is vital to understand the trade‐off between phase noise, lock time performance, and variability in ADPLL. We present the improved design optimal sampling digital PLL (OS‐DPLL) for IoT applications in this paper. The proposed OS‐DPLL consists of a loop module (LM), ring oscillator (RO), first‐order digital loop filter (F‐DLF), divider chain, and bang–bang phase frequency detector (BBPFD), which uses the improved bang–bang approach. In addition, an efficient operating system is introduced to isolated operating modes, which provide standard bandwidth performance for sound and spectral purity in a closed phase mode. The simulation result determines the effectiveness of the proposed OS‐DPLL design based on power consumption, hardware utilization, and throughput.