Orhan Sabah Abdullah
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Orhan Sabah Abdullah has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Luay Sadeq Al-Ansari
Mechanical Engineering Department, Faculty of Engineering, University of Kufa, Iraq
1 shared publication - Marwah Ghazi Kareem
Al-Qadisiyah University
1 shared publication - Mujtaba A. Flayyih
Biomedical Engineering Department, College of Engineering and Technologies, Al-Mustaqbal University, Hillah, Iraq
1 shared publication - Sadiq Emad Sadiq
Al-Furat Al-Awsat Technical University
1 shared publication
Latest Publications
- 25 April 2025
- Published by Taylor & Francis in Australian Journal of Mechanical Engineering
- Vol. 24 (1) , 14-27
Innovative fabrication and static analysis of porous functionally graded beams: experimental and finite element investigations
- 25 April 2025
- Published by Taylor & Francis in Australian Journal of Mechanical Engineering
- Vol. 24 (1) , 14-27
Innovative fabrication and static analysis of porous functionally graded beams: experimental and finite element investigations
- Open Access
- 9 May 2024
- Published by University of Technology, Iraq - DIGITAL COMMONS in Engineering and Technology Journal
- p. 1-8
Estimating the wear behavior of hdpe composites reinforced with nano alumina fillers using taguchi method
High-density polyethylene (HDPE), like other polymers is important in many applications due to its unique properties like low cost, weight, and availability. Recently, HDPE reinforced with ceramic fillers was considered in biomedical applications, especially in fabricating joint/bone replacements. Therefore, these applications required high wear resistance materials to serve under specific conditions. In this work, an optimization with Taguchi method was considered to associate the influence of nano alumina fillers, normal applied load, and sliding time on the wear rate values for hip joint replacement applications. In the first step, a TEM test was conducted on the prepared composites to ensure that the nanofillers were distributed within the matrix phase without agglomeration. The results indicated that the optimum wear resistance was seen in a composite made of HD PE +3% wt nano alumina fillers with a specific wear rate equal to 2.6652 10-6 in mm3/N.m, as well as the most effective parameters on wear rate are arranged as nano content, applied load, and the sliding time. In contrast, SEM observation was considered to understand the wear mechanism. The addition of nano Alumina fillers prevented the test specimen surface from lessening by creating a transfer film separating the contact zone results from the self-lubricant behavior generated in prepared composites. In contrast, deep grooves, adhesive marks, and debris particles were generated in pure HDPE specimens, resulting in low hardness and weak wear resistance.
- 9 May 2024
- Published by University of Technology, Iraq - DIGITAL COMMONS in Engineering and Technology Journal
- p. 1-8
Open AccessEstimating the wear behavior of hdpe composites reinforced with nano alumina fillers using taguchi method
High-density polyethylene (HDPE), like other polymers is important in many applications due to its unique properties like low cost, weight, and availability. Recently, HDPE reinforced with ceramic fillers was considered in biomedical applications, especially in fabricating joint/bone replacements. Therefore, these applications required high wear resistance materials to serve under specific conditions. In this work, an optimization with Taguchi method was considered to associate the influence of nano alumina fillers, normal applied load, and sliding time on the wear rate values for hip joint replacement applications. In the first step, a TEM test was conducted on the prepared composites to ensure that the nanofillers were distributed within the matrix phase without agglomeration. The results indicated that the optimum wear resistance was seen in a composite made of HD PE +3% wt nano alumina fillers with a specific wear rate equal to 2.6652 10-6 in mm3/N.m, as well as the most effective parameters on wear rate are arranged as nano content, applied load, and the sliding time. In contrast, SEM observation was considered to understand the wear mechanism. The addition of nano Alumina fillers prevented the test specimen surface from lessening by creating a transfer film separating the contact zone results from the self-lubricant behavior generated in prepared composites. In contrast, deep grooves, adhesive marks, and debris particles were generated in pure HDPE specimens, resulting in low hardness and weak wear resistance.