Jun Ho Hwang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jun Ho Hwang has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Keunbada Son
Advanced Dental Device Development Institute (A3DI), Kyungpook National University, 2177 Dalgubeol-daero, Jung-gu, Daegu 41940, Republic of Korea
2 shared publications - Kyu-Bok Lee
Professor, Department of Prosthodontics, School of Dentistry, Kyungpook National University, Daegu, Republic of Korea
2 shared publications - Gyeong-Min Kim
Department of Prosthodontics, School of Dentistry, Kyungpook National University, Daegu, Republic of Korea
1 shared publication - Gyu Ri Kim
Department of Dental Science, Graduate School, Kyungpook National University, Daegu, Republic of Korea
1 shared publication - Hoseong Cho
School of Electronic and Electrical Engineering, College of IT Engineering, Kyungpook National University, Daegu, Republic of Korea
1 shared publication - Hyun Deok Kim
Institute of Advanced Convergence Technology Kyungpook Nat. Univ 41061 Daegu Korea
1 shared publication
Latest Publications
- Open Access
- 1 January 2026
- Published by XMLink in The Journal of Advanced Prosthodontics
- Vol. 18 (2) , 103-115
Trueness and the amount of clinical adjustment for zirconia crowns fabricated by digital light processing at different build angles: a within-patient clinical study
This clinical study evaluated the effect of build angle (0°, 45°, and 90°) in digital light processing (DLP) printing on the trueness and chairside adjustment of zirconia crowns and compared these outcomes with conventionally milled crowns. Ten patients each received one milled zirconia crown and three DLP-printed zirconia crowns fabricated at 0°, 45°, and 90° build angles (40 crowns total; four crowns per patient). Trueness was calculated as the root mean square (RMS) surface deviation between intraoral scans of the crowns and the CAD design. Occlusal and intaglio adjustments were quantified as the RMS deviation between pre- and post-adjustment scans. Data were analyzed using linear mixed-effects models with manufacturing method as a fixed effect and patient as a random intercept to account for within-patient clustering. Post hoc comparisons were performed using Tukey-adjusted pairwise contrasts of estimated marginal means (α = .05). Manufacturing method significantly influenced trueness in the primary linear mixed-effects model (χ2 = 20.689, P = .001). Tukey-adjusted contrasts showed lower RMS for the 0° group (49.0 µm) than for the 45° group (63.3 µm; P = .033), 90° group (70.5 µm; P = .003), and milled group (66.2 µm; P = .012). Manufacturing method also affected occlusal adjustment (χ2 = 13.904, P = .003) and intaglio adjustment (χ2 = 28.624, P < .001). The milled group required more occlusal adjustment than the 0° group (P = .011), and greater intaglio adjustment than all DLP-printed groups (all P ≤ .004). Compared with milling, DLP-printed zirconia crowns demonstrated greater trueness (lower RMS) and required less chairside adjustment. Under the tested conditions, a 0° build angle was associated with the lowest trueness RMS and the least adjustment requirements.
- 1 January 2026
- Published by XMLink in The Journal of Advanced Prosthodontics
- Vol. 18 (2) , 103-115
Open AccessTrueness and the amount of clinical adjustment for zirconia crowns fabricated by digital light processing at different build angles: a within-patient clinical study
This clinical study evaluated the effect of build angle (0°, 45°, and 90°) in digital light processing (DLP) printing on the trueness and chairside adjustment of zirconia crowns and compared these outcomes with conventionally milled crowns. Ten patients each received one milled zirconia crown and three DLP-printed zirconia crowns fabricated at 0°, 45°, and 90° build angles (40 crowns total; four crowns per patient). Trueness was calculated as the root mean square (RMS) surface deviation between intraoral scans of the crowns and the CAD design. Occlusal and intaglio adjustments were quantified as the RMS deviation between pre- and post-adjustment scans. Data were analyzed using linear mixed-effects models with manufacturing method as a fixed effect and patient as a random intercept to account for within-patient clustering. Post hoc comparisons were performed using Tukey-adjusted pairwise contrasts of estimated marginal means (α = .05). Manufacturing method significantly influenced trueness in the primary linear mixed-effects model (χ2 = 20.689, P = .001). Tukey-adjusted contrasts showed lower RMS for the 0° group (49.0 µm) than for the 45° group (63.3 µm; P = .033), 90° group (70.5 µm; P = .003), and milled group (66.2 µm; P = .012). Manufacturing method also affected occlusal adjustment (χ2 = 13.904, P = .003) and intaglio adjustment (χ2 = 28.624, P < .001). The milled group required more occlusal adjustment than the 0° group (P = .011), and greater intaglio adjustment than all DLP-printed groups (all P ≤ .004). Compared with milling, DLP-printed zirconia crowns demonstrated greater trueness (lower RMS) and required less chairside adjustment. Under the tested conditions, a 0° build angle was associated with the lowest trueness RMS and the least adjustment requirements.
- Open Access
- 1 January 2025
- Published by XMLink in The Journal of Advanced Prosthodontics
- Vol. 17 (2) , 101-114
Effects of dental implant surface treated with sandblasting large grit acid-etching and femtosecond laser on implant stability, marginal bone volume, and histological results in a rabbit model
Son YT, et al. J Adv Prosthodont. 2025 Apr;17(2):101-114. https://doi.org/10.4047/jap.2025.17.2.101
- 1 January 2025
- Published by XMLink in The Journal of Advanced Prosthodontics
- Vol. 17 (2) , 101-114
Open AccessEffects of dental implant surface treated with sandblasting large grit acid-etching and femtosecond laser on implant stability, marginal bone volume, and histological results in a rabbit model
Son YT, et al. J Adv Prosthodont. 2025 Apr;17(2):101-114. https://doi.org/10.4047/jap.2025.17.2.101