Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Arka Dwinanda Soewono has a total of 35 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Techno-Economic Analysis of a Low-Cost Hybrid Heat Sink-Fan Cooling System for Solar Photovoltaic Panel: Case Study in West Java, Indonesia

    by Arka Dwinanda Soewono, Fernandi, Djoko Setyanto, Hadi Sutanto, Rexon Harris Simanjuntak, Marten Darmawan, Harjadi Gunawan, Karel Octavianus Bachri, Mochamad Januar

    Rising temperatures can negatively impact the performance of solar photovoltaic (PV) systems. To address this issue, a hybrid passive and active cooling for PV panels presents a viable solution to reduce excessive heating. However, only a few studies have assessed the economic viability of these hybrid PV cooling techniques. The purpose of this study is to examine the effect of a low-cost heat sink-fan cooling on the PV panel surface temperature and conversion efficiency, and analyze the production cost effectiveness factor (FCE) to assess the cooling system's performance. A comparative analysis found that the average surface temperature of the PV panel with a cooler was 11.97°C when exposed to solar irradiance of approximately 1,000 W/m2 and 9.73°C lower at around 800 W/m2 compared to the regular PV panel. This reduction in temperature led to an increase in the output voltage, current, and power in the solar PV with the cooler. The addition of heat sink-fan cooling yielded a 0.89 % to 1.02% improvement in the conversion efficiency of the PV module, depending on the intensity of the solar irradiation. The economic analysis based on the production cost effectiveness factor discovered that the mean value of the FCE for the hybrid heat-sink cooler ranged from 1.32 to 1.57. Since the FCE is greater than 1, the current heat sink-fan cooling system is considered cost-ineffective, indicating that further design improvements are necessary.


  • Open Access

    Pemanfaatan Stasiun Pengisi Daya Listrik Berbasis Energi Surya Di SMA Tarakanita Gading Serpong

    by Marten Darmawan, Arka Dwinanda Soewono, Harjadi Gunawan, Louis Eric Beavis, Bennettdei Shajila Shane Halim

    Institusi pendidikan seperti Sekolah Menegah Atas (SMA) Tarakanita Gading Serpong memiliki kebutuhan listrik yang besar untuk mendukung kegiatan belajar-mengajar sehingga diperlukan suatu stasiun pengisi daya yang memanfaatkan sumber energi ramah lingkungan. Oleh karena itu, tim pengabdi melakukan rancang bangun purwarupa stasiun pengisi daya berbasis panel surya yang dapat dipakai untuk mengisi gawai dan peralatan elektronik lainnya. Stasiun pengisi daya tersebut terdiri dari panel surya tipe polycrystalline 100 Watt, solar charge controller untuk pengaturan daya, baterai kering 33Ah untuk menyimpan kelebihan energi, dan inverter untuk menghasilkan arus listrik bolak-balik. Hasil pengujian menunjukan bahwa stasiun pengisi daya dapat berfungsi dengan baik di mana proses pengisi baterai smartphone 4500 mAh dapat dilakukan dalam kurun waktu sekitar 3 jam. Sosialisasi penggunaan dan perawatan stasiun pengisi daya kemudian dilaksanakan di mana para peserta yang terdiri dari perwakilan staf pendidik dan kependidikan SMA Tarakanita Gading Serpong menunjukan antusiasme yang tinggi pada saat mengikuti pelatihan. Hasil evaluasi kegiatan berbasis kuesioner menunjukkan bahwa perwakilan mitra merasa sangat puas terutama dari segi kegunaan dan manfaat stasiun pengisi daya. Diharapkan keberadaan stasiun pengisi daya ini dapat mendukung upaya mengurangi penggunaan sumber listrik berbasis fosil di lingkungan sekolah, serta menjadi media edukasi terkait penggunaan energi terbarukan bagi siswa-siswi Tarakanita Gading Serpong.

  • Open Access

    Structural Analysis of Brake Shoe under Static Load Using Al Alloy, Cast Iron, Mg Alloy for Main Components, and Carbon Variants for Brake Linings

    by Dony Eko Prasetyo, Hadi Sutanto, Arka Dwinanda Soewono

    The research is motivated by the issue faced by motorcycle users, namely the wear and tear of brake shoes, which can reduce braking effectiveness and increase the risk of accidents. The main objective of this study is to analyze the structural properties of motorcycle brake shoes with three different materials (aluminum alloy, cast iron, and magnesium alloy) and brake linings made of different carbon variants (alumina-carbon composite, carbon ceramics, and carbon fiber) under static pressures. Additional design aspects including weight and production cost are also evaluated during the material selection process for the motorcycle”™s brake shoe and brake lining. The 3D modeling of the brake shoe and lining was done in Solidworks using measurement data from a Coordinate Measuring Machine (CMM). The finite element analysis was performed using ABAQUS software. Considering the results from the finite element analysis, weight, and economic aspects, the study found that aluminum alloy (Al alloy) and carbon composite can be suitable materials for brake shoes and brake lining. The Al alloy brake shoe provides 62.7% weight saving while exhibiting good structural properties under static load and a moderate increase in production cost compared to cast iron. Similarly, brake lining with alumina-carbon composite showed the least deformation under static load while maintaining modest production costs compared to the other carbon variants.


  • Open Access

    Analisis Penyebab Kecacatan Dengan Menggunakan Metode Seven Tools Pada Proses Perakitan Mesin Sepeda Motor

    by Marten Darmawan, Arka Dwinanda Soewono, Nickolas Dario Wijaya, Karel Octavianus Bachri

    PT. SMT is a company that manufactures and distributes motorbikes. One of the main products assembled by PT. SMT is a 160 cc motorcycle engine. To improve the quality of the motorbike engine assembly process at PT. SMT, quality management based on the Seven Tools method has been performed. The check sheet analysis based on the production data from the January-July 2023 period shows that the most frequent quality issues in the engine assembly process are dirt on the cylinder inlet valve (64, 2%), followed by rust on the cylinder head (26.1%) and dirt on the gasket cover components for the cylinder head (9.8%). Root cause analysis using the Fishbone diagram finds that work environment factors including dirty workstations, equipment and components, as well as human factors are the main causes of product defects. From this analysis, the recommended improvements include implementing routine cleaning procedures for the work environment, equipment, and components, as well as providing additional training to improve operator competency and foster a better work culture.


  • Open Access

    Upaya Pencegahan Penyebaran COVID-19 Di SMA Providentia Melalui Penggunaan Alat Sterilisasi Dokumen

    by Marten Darmawan, Arka Dwinanda Soewono, Christiand, Luky Andreas

    Indonesia termasuk salah satu negara yang terdampak oleh pandemi COVID-19 di mana pemerintah menerapkan kebijakan Pemberlakuan Pembatasan Kegiatan Masyarakat (PPKM) sebagai upaya pencegahan penyebaran virus COVID-19. Hal ini menyebabkan banyak sektor kehidupan, termasuk sektor pendidikan, perlu menerapkan adaptasi cara hidup baru dengan menerapkan kegiatan belajar-mengajar secara daring selama PPKM berlangsung. Meskipun kegiatan belajar-mengajar dilakukan secara daring, kegiatan administrasi dan surat-menyurat di lembaga pendidikan berpotensi menjadi sumber penyebaran COVID-19 mengingat virus tersebut dapat bertahan pada permukaan benda untuk jangka waktu yang cukup lama. Sebagai salah satu cara pencegahan penyebaran virus COVID-19, tim pengabdi dari Universitas Katolik Atma Jaya telah merancang dan membangun purwarupa alat yang dapat mensterilkan permukaan kertas dan dokumen dari virus COVID-19. Mitra untuk pelaksanaan kegiatan pengabdian masyarakat ini adalah SMA Providentia. Alat sterilisasi dokumen ini menggunakan sinar UV-C yang dihasilkan oleh dua (2) buah lampu halogen berdaya 15-watt yang dipasang pada bagian bawah tutup alat sehingga dapat mensterilkan kertas yang masuk. Alat tersebut memiliki dimensi 425 mm x 304 mm x 149 mm, serta dapat memproses 5 lembar kertas per menit dan tumpukan kertas dengan maksimum ketebalan sebanyak 10 lembar. Tahap serah terima dan sosialisasi cara pengoperasian dan perawatan alat sterilisasi dokumen kemudian dilaksanakan dengan perwakilan terbatas dari mitra di ruang tata usaha SMA Providentia dikarenakan kondisi PPKM. Hasil kuisioner yang diisi oleh peserta sosialisasi yang terdiri dari lima orang karyawan kependidikan SMA Providentia menunjukan tingkat kepuasan yang tinggi sehingga dapat dinyatakan bahwa kegiatan berhasil mencapai tujuan utamanya yaitu mendukung pencegahan penyebaran virus COVID-19 di lingkungan SMA Providentia.


  • Open Access

    Analisis Kekuatan Purwarupa Swing Arm Untuk Sepeda Motor Listrik: Studi Kasus Pada PT “SC”

    by Karel Octavianus Bachri, Arka Dwinanda Soewono, Alfi Nabil

    In recent years, the automotive industry has been experiencing a significant transition from internal combustion engines that use fossil fuels to electric vehicles. PT “SC” is one of the leading companies engaged in converting and developing electric vehicles in Indonesia. This research aims to conduct a strength analysis of the swing arm prototype developed by PT “SC”. Simulations were performed using SolidWorks software to determine the impact of static loading on the von Mises stress and strain experienced by the swing arm made from SS 400 material. The total load on the swing arm was 1610N based on the electric dynamo's weight and the possible passengers' weight on the electric motorbike. The stress analysis results show that the maximum and minimum Mises stresses ​​are 5.38 x 106 N/m2 and 1.99 x 10-1 N/m2, respectively. This stress produces a maximum displacement value of 4.54 x 10-3 mm. Calculation results from Solidworks found that the safety factor for the swing arm prototype was 43, meaning the design is safe to use.


  • Open Access

    Perancangan Sistem Tata Udara dengan Software Bry-Air pada Ruang Kamar Tidur di Bogor, Indonesia

    by Arka Dwinanda Soewono, Gavin Alferio, Marten Darmawan

    An effective and efficient air system can provide optimal comfort and health for room occupants. This research uses Bry-Air Software to design an integrated air conditioning system that can improve comfort and health by considering temperature, humidity, air circulation, and air cleanliness. The design was carried out for a bedroom measuring 3 m x 3 mx 3 m using ASHRAE standards where the ideal room temperature is in the range of 23 ± 2°C, relative humidity 55 ± 5%, and ideal airflow of 108 Cubic Meters per Hour (CMH). ISO class 8 requirements with a maximum particle number of 100,000 particles/ft3 for a particle size of 0.5 µm are also used as a criteria during the design process to ensure clean air for room occupants. Simulation results from Bry-Air Software in accordance with ASHRAE and ISO standards found that the room needs to be equipped with a single Air Conditioner (AC) units with a capacity of ½ PK each, 1 Dehumidifier unit with a capacity of 51 CMH and an Air Cleaner with Pre-Filter and Medium Filter. The results of this research hopefully can contribute to developing integrated air conditioning systems for the comfort and health of building occupants in Indonesia.

  • Open Access

    Rancang Bangun Wastafel Multifungsi Untuk Tempat Perlindungan Hewan Fie Fie Jo

    by Arka Dwinanda Soewono, Marten Darmawan, Rory Anthony Hutagalung, Harjadi Gunawan, Fernandi, Vincent Yuwana

    Fie Fie Joe animal shelter employees and visitors often physically contact animals while feeding, playing with, or cleaning animals and their cages. In order to prevent virus and bacteria transmission, animal shelters require everyone to wash their hands after visiting the outdoor area. The Fie Fie Jo shelter, however, faced two main problems. First, only one hand-washing station is available in their facility, allowing possible viruses or bacteria to be transmitted through physical contact with other people or objects before entering the indoor facility. Second, their staff took a long time to bathe the animals in their enclosures since there was no washing station in the outdoor area. Therefore, this outreach program aims to design and build a multi-purpose washing station for the outdoor area that can be operated by a foot pedal so that users do not need to touch the faucet physically. The washing station has additional features such as a large tub that can also be used for bathing animals, a tissue holder, and a garbage disposal to help make it easier and faster to bathe several animals simultaneously. The method used during the outreach program includes conducting a survey, performing a design process, and demonstrating how to use and maintain the multi-purpose washing station. To assess the success of this program, the Fie Fie Jo owner and employees were asked to fill out a questionnaire. The results showed that they were more than satisfied with the demonstration and performance of the washing station. The presence of the multi-purpose washing station can improve productivity and reduce the risk of viruses and bacterial contamination of the Fie Fie Joe animal shelter employees and visitors.

  • Open Access

    Rancang Bangun Sistem Pendingin Evaporatif Berbasis Penyemprotan Air Untuk Meningkatkan Performa Air Conditioner

    by Arka Dwinanda Soewono, Nanda Viriya, Luky Andreas, Harjadi Gunawan, Marten Darmawan

    Air conditioner (AC) adalah sarana yang paling efektif untuk mendinginkan udara di dalam ruangan. Akan tetapi, peningkatan penggunaan AC membawa tantangan dari sisi pemenuhan kebutuhan energi listrik. Salah satu metode yang dapat digunakan untuk mengurangi konsumsi listrik AC yaitu dengan metode pendinginan evaporatif berbasis penyemprotan air. Maka dari itu, tujuan utama dari penelitian ini adalah melakukan rancang bangun sistem pendingin evaporatif yang dapat diaplikasikan langsung pada AC tipe split berukuran 1 PK. Sistem pendingin evaporatif menggunakan pompa untuk mengalirkan air ke nozzle yang terpasang pada rangka aluminium yang dapat dipasang di belakang kondensor AC tanpa memerlukan modifikasi. Kalibrasi menghasilkan pengaturan optimal di mana pompa dioperasikan untuk menghasilkan debit aliran sebesar 0,8 liter/menit dengan jarak antara nozzle dengan kondensor sejauh 20 cm. Hasil pengujian menunjukan bahwa penggunaan sistem pendingin evaporatif dengan konfigurasi optimal memberikan penurunan konsumsi listrik total sebesar 13,19 % dan memberikan peningkatan Coefficient of Performance sebesar 9,03 %.


  • Open Access

    Analisa Kerusakan Bantalan Pada Boiler Feedwater Pump

    by Arka Dwinanda Soewono, Ezra Raditya Gunawan, Marten Darmawan

    The sliding bearing is an essential component in a centrifugal pump to withstand the loads and forces during the operation of the pump. Damage to the plain bearing component can decrease pump performance and cause further damage to other components. This research aims to analyze the damage that occurs to the bearing used in a boiler feedwater pump and determine the cause of the damage. The analysis was carried out by observing the forms of damage to the Babbitt layer on the bearing, identifying potential failures using the Failure Modes and Effect Analysis (FMEA) method, and establishing the root cause of the failure using the fishbone diagram. The analysis results show that the leading cause of damage to the bearing for the boiler feedwater pump is the bulk loss of the babbitt layer on the bearings.