Bowen Gao
Bowen Gao has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Zhifang Hu
GRINM Resources and Environment Technology Co., Ltd., Beijing 101047, China
2 shared publications - Chen Liu
School of Civil and Resource Engineering, University of Science and Technology Beijing, Beijing 100083, China
1 shared publication - Honglin Jiang
National Engineering Research Center for Environment-Friendly Metallurgy in Producing Premium Non-Ferrous Metals, Beijing 101407, China
1 shared publication - Qidong Zhang
GRINM Resources and Environment Technology Co., Ltd., Beijing 101047, China
1 shared publication - Qidong Zhang
National Engineering Research Center for Environment-Friendly Metallurgy in Producing Premium Non-Ferrous Metals, Beijing 101407, China
1 shared publication - Xiaoli Li
China National Jinyu Gold Materials and Equipment Co., Ltd., Beijing 100101, China
1 shared publication
Latest Publications
- Open Access
Preparation of High-Purity Vanadium Metal by Iodide Refining Based on Numerical Simulation Using SIMPLE Algorithm
In this study, the iodide refining of high-purity vanadium metal was investigated experimentally and by two-dimensional numerical simulations based on the SIMPLE (Semi-Implicit Method for Pressure-Linked Equations) algorithm. The effects of system temperature, K values (characterizing the deposition filament temperature), initial iodine amount, and raw material packing configuration on the deposition rate, crystal morphology, and mass transport were studied in a custom-built iodide apparatus. The experimental results showed that the deposition rate exhibited a bell-shaped dependence on the source temperature. The optimal source temperature and optimal K value were 1123–1173 K and 40–50, respectively, at which the average deposition rate reached its peak. Both the average deposition rate and the average reaction time increased slightly with increasing initial iodine amount, but the increases were limited. Full loading of the raw material yielded crystal rods of uniform size. Vanadium crystal rods with a diameter of approximately 20 mm were obtained after refining. The metallic impurities Fe, Cr, Al, and Si were reduced to 0.025–0.033 wt.%, 2 partial-pressure difference, and decreased with increasing transport distance. The flow pattern transitioned from pure diffusion/advection at 300 Pa to transitional vortices at 1000 Pa, and finally to fully developed recirculation at 3000 Pa. The simulation results are qualitatively consistent with the experimental observations, providing a theoretical basis for process optimization. To further improve the purity and scale-up potential of the process, it is necessary to conduct more in-depth research, including the development of fully coupled models that incorporate gas-phase dissociation, non-equilibrium surface kinetics, and composition-dependent mixture properties, as well as three-dimensional simulations and reactor material optimization.
Open AccessPreparation of High-Purity Vanadium Metal by Iodide Refining Based on Numerical Simulation Using SIMPLE Algorithm
In this study, the iodide refining of high-purity vanadium metal was investigated experimentally and by two-dimensional numerical simulations based on the SIMPLE (Semi-Implicit Method for Pressure-Linked Equations) algorithm. The effects of system temperature, K values (characterizing the deposition filament temperature), initial iodine amount, and raw material packing configuration on the deposition rate, crystal morphology, and mass transport were studied in a custom-built iodide apparatus. The experimental results showed that the deposition rate exhibited a bell-shaped dependence on the source temperature. The optimal source temperature and optimal K value were 1123–1173 K and 40–50, respectively, at which the average deposition rate reached its peak. Both the average deposition rate and the average reaction time increased slightly with increasing initial iodine amount, but the increases were limited. Full loading of the raw material yielded crystal rods of uniform size. Vanadium crystal rods with a diameter of approximately 20 mm were obtained after refining. The metallic impurities Fe, Cr, Al, and Si were reduced to 0.025–0.033 wt.%, 2 partial-pressure difference, and decreased with increasing transport distance. The flow pattern transitioned from pure diffusion/advection at 300 Pa to transitional vortices at 1000 Pa, and finally to fully developed recirculation at 3000 Pa. The simulation results are qualitatively consistent with the experimental observations, providing a theoretical basis for process optimization. To further improve the purity and scale-up potential of the process, it is necessary to conduct more in-depth research, including the development of fully coupled models that incorporate gas-phase dissociation, non-equilibrium surface kinetics, and composition-dependent mixture properties, as well as three-dimensional simulations and reactor material optimization.
- Open Access
- 13 May 2025
- Published by MDPI AG in Separations
- Vol. 12 (5) , 123
Study on Floatation Separation of Molybdenite and Talc Based on Crystal Surface Anisotropy
Talcose molybdenite resources are abundant but resource utilization is low. The floatation separation of molybdenite (MoS2) and talc is challenging due to their similar natural hydrophobicity and layered structures. This study investigates the surface properties and interaction mechanisms between these minerals to improve their separation efficiency. Density functional theory (DFT) calculations confirm that the basal planes of both minerals are hydrophobic, while their edge surfaces are hydrophilic. Atomic force microscopy (AFM) and DLVO theory reveal that molybdenite and talc particles aggregate in neutral/acidic conditions but disperse in alkaline solutions due to altered surface forces. Floatation experiments demonstrate that pulp pH is the key controlling factor—alkaline conditions (pH > 10) effectively reduce hetero-aggregation, enabling selective molybdenite recovery. These findings provide critical insights into optimizing floatation processes for talcose molybdenite ores, enhancing resource utilization.
- 13 May 2025
- Published by MDPI AG in Separations
- Vol. 12 (5) , 123
Open AccessStudy on Floatation Separation of Molybdenite and Talc Based on Crystal Surface Anisotropy
Talcose molybdenite resources are abundant but resource utilization is low. The floatation separation of molybdenite (MoS2) and talc is challenging due to their similar natural hydrophobicity and layered structures. This study investigates the surface properties and interaction mechanisms between these minerals to improve their separation efficiency. Density functional theory (DFT) calculations confirm that the basal planes of both minerals are hydrophobic, while their edge surfaces are hydrophilic. Atomic force microscopy (AFM) and DLVO theory reveal that molybdenite and talc particles aggregate in neutral/acidic conditions but disperse in alkaline solutions due to altered surface forces. Floatation experiments demonstrate that pulp pH is the key controlling factor—alkaline conditions (pH > 10) effectively reduce hetero-aggregation, enabling selective molybdenite recovery. These findings provide critical insights into optimizing floatation processes for talcose molybdenite ores, enhancing resource utilization.