Petro Kurliak
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Petro Kurliak has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Oleksii Chornyi
Department of Systems of Automatic Control and Electric Drive Kremenchuk Mykhailo Ostrohradskyi National University Kremenchuk Ukraine
3 shared publications - Valerii Tytiuk
Kryvyi Rih National University, Ukraine
3 shared publications - Galina Sivyakova
Karaganda Industrial University Temirtau Kazakhstan
2 shared publications - Valeriy Druzhinin
Department of Energy Karaganda Industrial University Temirtau Kazakhstan
2 shared publications - Victor Busher
National University “Odessa Maritime Academy
2 shared publications - Alexey Kalinin
Abylkas Saginov Karaganda Technical University
1 shared publication
Latest Publications
- Open Access
- 29 January 2025
- Published by Lithuanian Academy of Sciences in Energetika
- Vol. 71 (1) , 78-91
Improvement of human–machine interface of complex technical systems using fractional-order PIλDμ controllers
One of the most essential characteristics of a complex technical system is that it performs ‘an important useful function only with the assistance of a human operator and standard infrastructures…’ [1]. At the earliest stages of the development of a system, deciding whether the human operator should be regarded as part of the complex system or an external entity is necessary. In most cases, the human operator should be treated as an external entity.Most complex technical systems cannot function without the active involvement of a human operator, who retains responsibility for decision-making, control, and management functions. From a functional standpoint, operators can be considered an integral part of the system. However, the system designer rarely possesses sufficient authority over the operator to incorporate them fully into the system’s design. From the perspective of the systems engineer, the human operator instead represents an element of the system’s environment.Under this paradigm, the systems engineer must devote particular attention to the design and development of the operator interface, which is a critically important aspect of any complex technical system [2]. Accordingly, the development of universal technical solutions that enhance the quality of the human–machine interface in complex technical systems represents both a significant and timely challenge, the resolution of which can be applied across a wide range of practical applications.The primary objective of the present work is to improve the performance of the human–machine interface by compensating for the inertial and nonlinear characteristics of the human operator as a control element within a complex technical system.
- 29 January 2025
- Published by Lithuanian Academy of Sciences in Energetika
- Vol. 71 (1) , 78-91
Open AccessImprovement of human–machine interface of complex technical systems using fractional-order PIλDμ controllers
One of the most essential characteristics of a complex technical system is that it performs ‘an important useful function only with the assistance of a human operator and standard infrastructures…’ [1]. At the earliest stages of the development of a system, deciding whether the human operator should be regarded as part of the complex system or an external entity is necessary. In most cases, the human operator should be treated as an external entity.Most complex technical systems cannot function without the active involvement of a human operator, who retains responsibility for decision-making, control, and management functions. From a functional standpoint, operators can be considered an integral part of the system. However, the system designer rarely possesses sufficient authority over the operator to incorporate them fully into the system’s design. From the perspective of the systems engineer, the human operator instead represents an element of the system’s environment.Under this paradigm, the systems engineer must devote particular attention to the design and development of the operator interface, which is a critically important aspect of any complex technical system [2]. Accordingly, the development of universal technical solutions that enhance the quality of the human–machine interface in complex technical systems represents both a significant and timely challenge, the resolution of which can be applied across a wide range of practical applications.The primary objective of the present work is to improve the performance of the human–machine interface by compensating for the inertial and nonlinear characteristics of the human operator as a control element within a complex technical system.
- Open Access
- 29 January 2025
- Published by Lithuanian Academy of Sciences in Energetika
- Vol. 71 (1)
Electric drive excitation control for improved performance of hot rolling mill finishing groups
The study presented in the paper investigates rigorously the methods for enhancing the performance of interconnected electric drives within the finishing group of a hot rolling mill. In particular, it examines the impact of supply voltage fluctuations on drive precision and the interactions mediated by the rolled metal strip. A detailed analysis of the existing power supply system identifies the primary causes of dynamic deviations in drive operation.A combined angular velocity control system is proposed to regulate the excitation of DC electric motors. The adaptive control strategy modulates magnetic flux during grid voltage drops, thereby reducing speed fluctuations and minimising tension inconsistencies in the inter-stand gaps. Unlike conventional systems that disregard supply voltage variations, the adaptive approach significantly improves the stability of the rolling process.A mathematical model of the system, incorporating second- and third-order elastic couplings arising from both mechanical and electromagnetic interactions among the drives, is developed. Numerical simulations conducted in MATLAB/Simulink validate the efficiency of the proposed method. Optimal values for the relative reduction in the magnetic flux are determined to minimise discrepancies in drive currents and strip elongation. The results confirm that implementing adaptive control enhances system stability, improves rolling quality, and reduces the load on the power supply, thereby supporting its adoption in rolling mills operating under unstable grid voltage conditions.
- 29 January 2025
- Published by Lithuanian Academy of Sciences in Energetika
- Vol. 71 (1)
Open AccessElectric drive excitation control for improved performance of hot rolling mill finishing groups
The study presented in the paper investigates rigorously the methods for enhancing the performance of interconnected electric drives within the finishing group of a hot rolling mill. In particular, it examines the impact of supply voltage fluctuations on drive precision and the interactions mediated by the rolled metal strip. A detailed analysis of the existing power supply system identifies the primary causes of dynamic deviations in drive operation.A combined angular velocity control system is proposed to regulate the excitation of DC electric motors. The adaptive control strategy modulates magnetic flux during grid voltage drops, thereby reducing speed fluctuations and minimising tension inconsistencies in the inter-stand gaps. Unlike conventional systems that disregard supply voltage variations, the adaptive approach significantly improves the stability of the rolling process.A mathematical model of the system, incorporating second- and third-order elastic couplings arising from both mechanical and electromagnetic interactions among the drives, is developed. Numerical simulations conducted in MATLAB/Simulink validate the efficiency of the proposed method. Optimal values for the relative reduction in the magnetic flux are determined to minimise discrepancies in drive currents and strip elongation. The results confirm that implementing adaptive control enhances system stability, improves rolling quality, and reduces the load on the power supply, thereby supporting its adoption in rolling mills operating under unstable grid voltage conditions.
- Open Access
- 28 January 2025
- Published by Lithuanian Academy of Sciences in Energetika
- Vol. 71 (1)
Using asynchronous programming to improve computer simulation performance in energy systems
Due to the progressing complexity of modern energy systems, the need to forecast energy consumption and generation, optimise processes and develop new technologies in the energy sector, analyse scenarios for the development of energy systems and elaborate a strategy for their development, modelling and simulation is of particular relevance in this industry. The growing need to improve the productivity of computer simulation in the energy industry is effectively addressed by utilising modern computer architectures and advanced software tools that provide acceleration for computationally intensive tasks. Research presented in this paper focuses on enhancing the performance of computationally intensive algorithms using the Thomas algorithm by employing modern asynchronous programming techniques. The work implements classical and develops and implements asynchronous computational algorithms of the sweep method with subsequent assessment of the time and efficiency of their execution for the order of systems of linear equations (SLAEs) up to 5 × 107. The program code was developed using Microsoft Visual Studio C++ and the standard template for asynchronous programming. The numerical experiments showed the possibility of increasing of the implementation speed of the asynchronous algorithm by 1.87–2.91 times. Research results correspond with the literature data and the results previously obtained by the authors in similar studies using alternative parallel programming software. In general, the results of this study determine the potential for further improvement and development of methods and technologies for parallel implementation of computational tasks using the Tridiagonal Matrix Algorithm. These approaches can be extended to developing various computer models of energy processes and systems based on the solution of SLAEs with tridiagonal matrices on computers with multiprocessor or multi-core architectures.
- 28 January 2025
- Published by Lithuanian Academy of Sciences in Energetika
- Vol. 71 (1)
Open AccessUsing asynchronous programming to improve computer simulation performance in energy systems
Due to the progressing complexity of modern energy systems, the need to forecast energy consumption and generation, optimise processes and develop new technologies in the energy sector, analyse scenarios for the development of energy systems and elaborate a strategy for their development, modelling and simulation is of particular relevance in this industry. The growing need to improve the productivity of computer simulation in the energy industry is effectively addressed by utilising modern computer architectures and advanced software tools that provide acceleration for computationally intensive tasks. Research presented in this paper focuses on enhancing the performance of computationally intensive algorithms using the Thomas algorithm by employing modern asynchronous programming techniques. The work implements classical and develops and implements asynchronous computational algorithms of the sweep method with subsequent assessment of the time and efficiency of their execution for the order of systems of linear equations (SLAEs) up to 5 × 107. The program code was developed using Microsoft Visual Studio C++ and the standard template for asynchronous programming. The numerical experiments showed the possibility of increasing of the implementation speed of the asynchronous algorithm by 1.87–2.91 times. Research results correspond with the literature data and the results previously obtained by the authors in similar studies using alternative parallel programming software. In general, the results of this study determine the potential for further improvement and development of methods and technologies for parallel implementation of computational tasks using the Tridiagonal Matrix Algorithm. These approaches can be extended to developing various computer models of energy processes and systems based on the solution of SLAEs with tridiagonal matrices on computers with multiprocessor or multi-core architectures.
- Open Access
- 2 August 2024
- Published by Lithuanian Academy of Sciences in Energetika
- Vol. 70 (1)
Mathematical modelling of induction motors taking into account design-parameter asymmetry
Due to their numerous technical and economic advantages, induction machines (IM) with squirrel-cage rotors are important components of many industrial processes. Their reliability, durability, and ease of operation make them indispensable in various industries, ensuring stable and efficient equipment performance. However, to minimise the risk of costly production failures caused by sudden stoppages, it is important to implement effective diagnostic and monitoring methods. The most common type of fault in squirrel-cage induction motors is the breakage of cage bars and end ring segments, particularly in motors with high inertia loads and frequent stops and starts. Regular maintenance and the implementation of modern control systems in the industry will help ensure the reliable and uninterrupted operation of these machines. In the technical literature, various diagnostic methods have been proposed. Some are based on analysing data collected from the induction motor (IM), detecting characteristic perturbations that indicate faults in the machine. Other methods involve comparing the data obtained from the actual induction motor with its digital model. It is clear that accurate and adequate IM models are necessary for the development and optimisation of fault diagnosis methods. This paper focuses on developing a mathematical model of an induction motor (IM) in a stator-fixed coordinate system, where the squirrel-cage rotor of the IM is represented as a multiphase, symmetrically distributed winding system in space. The adequacy of the obtained model is demonstrated. The developed model allows for the analysis of various types of asymmetries in both stator and rotor of squirrel-cage induction motors
- 2 August 2024
- Published by Lithuanian Academy of Sciences in Energetika
- Vol. 70 (1)
Open AccessMathematical modelling of induction motors taking into account design-parameter asymmetry
Due to their numerous technical and economic advantages, induction machines (IM) with squirrel-cage rotors are important components of many industrial processes. Their reliability, durability, and ease of operation make them indispensable in various industries, ensuring stable and efficient equipment performance. However, to minimise the risk of costly production failures caused by sudden stoppages, it is important to implement effective diagnostic and monitoring methods. The most common type of fault in squirrel-cage induction motors is the breakage of cage bars and end ring segments, particularly in motors with high inertia loads and frequent stops and starts. Regular maintenance and the implementation of modern control systems in the industry will help ensure the reliable and uninterrupted operation of these machines. In the technical literature, various diagnostic methods have been proposed. Some are based on analysing data collected from the induction motor (IM), detecting characteristic perturbations that indicate faults in the machine. Other methods involve comparing the data obtained from the actual induction motor with its digital model. It is clear that accurate and adequate IM models are necessary for the development and optimisation of fault diagnosis methods. This paper focuses on developing a mathematical model of an induction motor (IM) in a stator-fixed coordinate system, where the squirrel-cage rotor of the IM is represented as a multiphase, symmetrically distributed winding system in space. The adequacy of the obtained model is demonstrated. The developed model allows for the analysis of various types of asymmetries in both stator and rotor of squirrel-cage induction motors
- Open Access
- 1 December 2023
- Published by Ivano-Frankivsk National Technical University of Oil and Gas in PRECARPATHIAN BULLETIN OF THE SHEVCHENKO SCIENTIFIC SOCIETY. Number
- No. 18(68),p. 9-17
ON POSITIVE CONTINUOUS FUNCTIONS DEFINED IN THE UNIT POLYDISC
In theory of holomorphic functions having bounded L-index in a direction b an auxiliary class of positive continuous functions L is important to describe properties of the holomorphic functions by some inequalities and estimates containing the function L. This class is defined by local behavior of the function L. In the simplest one-dimensional case, the function should not vary locally too quickly, i.e. L(r+O(1/L(r))) = O(L(r)) for r = |z| → +∞. The paper is devoted an analog of this function class for the unit polydisc, i.e. for the Cartesian product of the unit discs. There is proved an equivalence of three different approaches to define the class. It is described by the local behavior on the slice z+tb for given z from the unit polydisc and for a fixed direction b, where the complex variable t belongs to some disc with radius dependent on b and z. These estimates must be fulfilled uniformly in all z. There is indicated a possible explicit form of functions belonging to the class. The form is given as a product of arbitrary positive continuous function defined in the closed unit polydisc and the minimum of the expressions 1/(1−|z j|) in all variables z j.
- 1 December 2023
- Published by Ivano-Frankivsk National Technical University of Oil and Gas in PRECARPATHIAN BULLETIN OF THE SHEVCHENKO SCIENTIFIC SOCIETY. Number
- No. 18(68),p. 9-17
Open AccessON POSITIVE CONTINUOUS FUNCTIONS DEFINED IN THE UNIT POLYDISC
In theory of holomorphic functions having bounded L-index in a direction b an auxiliary class of positive continuous functions L is important to describe properties of the holomorphic functions by some inequalities and estimates containing the function L. This class is defined by local behavior of the function L. In the simplest one-dimensional case, the function should not vary locally too quickly, i.e. L(r+O(1/L(r))) = O(L(r)) for r = |z| → +∞. The paper is devoted an analog of this function class for the unit polydisc, i.e. for the Cartesian product of the unit discs. There is proved an equivalence of three different approaches to define the class. It is described by the local behavior on the slice z+tb for given z from the unit polydisc and for a fixed direction b, where the complex variable t belongs to some disc with radius dependent on b and z. These estimates must be fulfilled uniformly in all z. There is indicated a possible explicit form of functions belonging to the class. The form is given as a product of arbitrary positive continuous function defined in the closed unit polydisc and the minimum of the expressions 1/(1−|z j|) in all variables z j.