Mohamed Lotfi Cherrad
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mohamed Lotfi Cherrad has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Billel Hamadi
Institution: Research Center in Industrial Technologies CRTI Address Cheraga Algiers Algeria
3 shared publications - Djamel Boucherma
Research Center in Industrial Technologies CRTI, P.O. Box 64, Cheraga, 16014, Algiers, Algeria
3 shared publications - Mohamed Chaour
Doctor in Mechanics Institution: Research Center in Industrial Technologies CRTI Address Cheraga Algiers Algeria
2 shared publications Sofiane Boulkroune
2 shared publicationsSofiane Chorfi
2 shared publications- Toufik Achour
Doctor in Mechanics Institution: Research Center in Industrial Technologies CRTI Address Cheraga Algiers Algeria
2 shared publications
Latest Publications
- Open Access
- 26 September 2025
- Published by Iskender AKKURT in International Journal of Computational and Experimental Science and Engineering
- Vol. 11 (4)
Numerical Investigation of Fluid Effects on Heat Transfer of Nanofluids in a Plane Channel: Application to Solar Thermal Panels
In this work, a numerical investigation is conducted to analyze laminar mixed convection of nanofluids in a two-dimensional horizontal channel. The lower wall of the channel dissipates heat at constant hot temperature, whereas the upper wall is adiabatic. The analysis considers five volume concentrations (φ) of copper nanoparticles (Cu), ranging from 0 to 0.2, suspended in common base fluids such as ethylene glycol, soybean oil, and sunflower oil. The effective thermal conductivity and dynamic viscosity of the nanofluid are estimated using the Maxwell-Garnett and Brinkman models, respectively. The set of governing equations is derived and solved numerically through a finite difference discretization. For numerical resolution, a line-by-line sweeping strategy in combination with the Thomas algorithm (TDMA) is implemented. The objective of this study is to investigate how viscosity and thermal conductivity influence both heat transfer and flow behavior, in order to determine the nanofluid that maximizes thermal performance. The outcomes are expected to contribute to enhancing the use of nanofluids in advanced thermal control systems.
- 26 September 2025
- Published by Iskender AKKURT in International Journal of Computational and Experimental Science and Engineering
- Vol. 11 (4)
Open AccessNumerical Investigation of Fluid Effects on Heat Transfer of Nanofluids in a Plane Channel: Application to Solar Thermal Panels
In this work, a numerical investigation is conducted to analyze laminar mixed convection of nanofluids in a two-dimensional horizontal channel. The lower wall of the channel dissipates heat at constant hot temperature, whereas the upper wall is adiabatic. The analysis considers five volume concentrations (φ) of copper nanoparticles (Cu), ranging from 0 to 0.2, suspended in common base fluids such as ethylene glycol, soybean oil, and sunflower oil. The effective thermal conductivity and dynamic viscosity of the nanofluid are estimated using the Maxwell-Garnett and Brinkman models, respectively. The set of governing equations is derived and solved numerically through a finite difference discretization. For numerical resolution, a line-by-line sweeping strategy in combination with the Thomas algorithm (TDMA) is implemented. The objective of this study is to investigate how viscosity and thermal conductivity influence both heat transfer and flow behavior, in order to determine the nanofluid that maximizes thermal performance. The outcomes are expected to contribute to enhancing the use of nanofluids in advanced thermal control systems.
- Open Access
- 1 November 2024
- Published by Brazilian Journals in South Florida Journal of Development
- Vol. 5 (11) , e4663
Numerical study of laminar mixed convection under steady and unsteady flow conditions
The present work consists of a numerical study of laminar mixed convection in a square cavity, a cavity has been chosen whose left vertical wall is mobile and subjected to a cold temperature, while the right wall is considered fixed and hot. The horizontal walls are adiabatic. where configuration of the lid-driven enclosure is encountered in many realistic engineering and industrial applications, such as, contains cooling of electronic devices, materials processing, flow and heat transfer in solar ponds, thermal-hydraulics of nuclear reactors and metal coating. The governing equations are the continuity equation, the Navier-Stocks equations, and the energy equation. These equations are discretized by the finite volume method. The objective of this work is to study the effect of the Reynolds and Grashof numbers on the structure of the flow. We were able to determine the correlation between the number Gr and Re to determine the transition boundaries from one convection regime to another regime (laminar, then transient).
- 1 November 2024
- Published by Brazilian Journals in South Florida Journal of Development
- Vol. 5 (11) , e4663
Open AccessNumerical study of laminar mixed convection under steady and unsteady flow conditions
The present work consists of a numerical study of laminar mixed convection in a square cavity, a cavity has been chosen whose left vertical wall is mobile and subjected to a cold temperature, while the right wall is considered fixed and hot. The horizontal walls are adiabatic. where configuration of the lid-driven enclosure is encountered in many realistic engineering and industrial applications, such as, contains cooling of electronic devices, materials processing, flow and heat transfer in solar ponds, thermal-hydraulics of nuclear reactors and metal coating. The governing equations are the continuity equation, the Navier-Stocks equations, and the energy equation. These equations are discretized by the finite volume method. The objective of this work is to study the effect of the Reynolds and Grashof numbers on the structure of the flow. We were able to determine the correlation between the number Gr and Re to determine the transition boundaries from one convection regime to another regime (laminar, then transient).
- Open Access
- 1 July 2024
- Published by Brazilian Journals in STUDIES IN ENGINEERING AND EXACT SCIENCES
- Vol. 5 (2) , e9904
Chip formation analysis during dry turning of C45 steel
Machining is a material removal process that creates surfaces through chip formation using a cutting tool. The morphology of the chips and the mechanisms governing their formation directly affect the quality of machined parts. This experimental study examines chip formation mechanisms in the dry turning of C45 steel under various cutting conditions, utilizing coated carbide inserts. Machining performance was evaluated based on key chip morphology parameters, including shape, length, thickness, and volume. The results show that increasing cutting speed (Vc) produces shorter, thicker chips without significantly altering their predominantly helical shape. A higher feed rate (f) maintains the tangled ribbon form of the chips but leads to longer chip production. Additionally, changes in the depth of cut (ap) create instabilities that result in varied chip morphologies, including long tubular, short helical, and elementary forms. As the depth of cut increases, chips become shorter and thinner. These findings provide valuable insights into the material's deformation and fracture mechanisms, enhancing our understanding of chip formation and its impact on the efficiency of dry turning operations on C45 steel.
- 1 July 2024
- Published by Brazilian Journals in STUDIES IN ENGINEERING AND EXACT SCIENCES
- Vol. 5 (2) , e9904
Open AccessChip formation analysis during dry turning of C45 steel
Machining is a material removal process that creates surfaces through chip formation using a cutting tool. The morphology of the chips and the mechanisms governing their formation directly affect the quality of machined parts. This experimental study examines chip formation mechanisms in the dry turning of C45 steel under various cutting conditions, utilizing coated carbide inserts. Machining performance was evaluated based on key chip morphology parameters, including shape, length, thickness, and volume. The results show that increasing cutting speed (Vc) produces shorter, thicker chips without significantly altering their predominantly helical shape. A higher feed rate (f) maintains the tangled ribbon form of the chips but leads to longer chip production. Additionally, changes in the depth of cut (ap) create instabilities that result in varied chip morphologies, including long tubular, short helical, and elementary forms. As the depth of cut increases, chips become shorter and thinner. These findings provide valuable insights into the material's deformation and fracture mechanisms, enhancing our understanding of chip formation and its impact on the efficiency of dry turning operations on C45 steel.