Nihal Ahmed
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Nihal Ahmed has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Abid Hossain
Department of Mechanical Engineering, University of Arkansas at Little Rock, Little Rock, AR 72204, USA
1 shared publication - Bo Shen
Department of Mechanical Engineering, University of Arkansas at Fayetteville, Fayetteville, AR 72701, USA
1 shared publication - Janak Paudel
School of Physical Sciences, University of Arkansas at Little Rock, 2801 South University Avenue, Little Rock, Arkansas 72204, United States
1 shared publication - Maharshi Dey
UbiQD Inc., Los Alamos, NM 87544, USA
1 shared publication Mahmudul Hassan
School of Physical Sciences, University of Arkansas at Little Rock, Little Rock, USA
1 shared publicationMohammad Ashikul Alam
Department of Mechanical Engineering, University of Arkansas at Little Rock, Little Rock, USA
1 shared publication
Latest Publications
- Open Access
- 23 April 2026
- Published by MDPI AG in Lubricants
- Vol. 14 (5) , 183
Controlled Laser Sintering as a Strategy for Improved Tribological Performance of Ni-Cr-Ti3SiC2 Coatings
The poor tribological and mechanical performance of Al alloys hinders their use in practical applications where low COF and high durability are required. This study examined and evaluated a novel laser-sintered Ni-Cr coating to improve the load-carrying capacity and tribological performance of an Al alloy (Al 6061) substrate. The authors demonstrate that laser sintering cycle count is a decisive process variable governing coating dispersion, microstructural consolidation, and tribological performance in Ni-Cr coatings fabricated via Selective Laser Sintering (SLS). Increasing the laser cycle count progressively refined the surface morphology, improved coating dispersion, and strengthened interparticle bonding. As a result, the average durability after three cycles was seven times that after one laser cycle, accompanied by markedly improved COF. To further improve durability and load-carrying capacity, Ti3SiC2 was introduced into the Ni-Cr coating. The coating containing 10 wt% Ti3SiC2 exhibited a 20-fold increase in durability, extending the time to failure to approximately 70,000 s (700 m) while maintaining a low coefficient of friction (~0.48) compared with the coating containing no Ti3SiC2. The greater durability of the Ni-Cr-10wt%Ti3SiC2 coating in this novel study was attributed to improved adhesion to the substrate, better particle distribution during sintering, and greater load-carrying capacity. While further process changes do not yield feasible samples, this study showed that surface properties can be improved within the available small-process regime. Overall, laser sintering of a Ni-Cr-10wt%Ti3SiC2 coating shows promise as a means to improve the tribological and mechanical performance of Al 6061. This study should aid researchers and other stakeholders in fabricating well-adhering, durable, and tribotactic composite coatings on Al6061 and similar material systems.
- 23 April 2026
- Published by MDPI AG in Lubricants
- Vol. 14 (5) , 183
Open AccessControlled Laser Sintering as a Strategy for Improved Tribological Performance of Ni-Cr-Ti3SiC2 Coatings
The poor tribological and mechanical performance of Al alloys hinders their use in practical applications where low COF and high durability are required. This study examined and evaluated a novel laser-sintered Ni-Cr coating to improve the load-carrying capacity and tribological performance of an Al alloy (Al 6061) substrate. The authors demonstrate that laser sintering cycle count is a decisive process variable governing coating dispersion, microstructural consolidation, and tribological performance in Ni-Cr coatings fabricated via Selective Laser Sintering (SLS). Increasing the laser cycle count progressively refined the surface morphology, improved coating dispersion, and strengthened interparticle bonding. As a result, the average durability after three cycles was seven times that after one laser cycle, accompanied by markedly improved COF. To further improve durability and load-carrying capacity, Ti3SiC2 was introduced into the Ni-Cr coating. The coating containing 10 wt% Ti3SiC2 exhibited a 20-fold increase in durability, extending the time to failure to approximately 70,000 s (700 m) while maintaining a low coefficient of friction (~0.48) compared with the coating containing no Ti3SiC2. The greater durability of the Ni-Cr-10wt%Ti3SiC2 coating in this novel study was attributed to improved adhesion to the substrate, better particle distribution during sintering, and greater load-carrying capacity. While further process changes do not yield feasible samples, this study showed that surface properties can be improved within the available small-process regime. Overall, laser sintering of a Ni-Cr-10wt%Ti3SiC2 coating shows promise as a means to improve the tribological and mechanical performance of Al 6061. This study should aid researchers and other stakeholders in fabricating well-adhering, durable, and tribotactic composite coatings on Al6061 and similar material systems.
- Open Access
- 19 May 2025
- Published by Springer Nature in Discover Mechanical Engineering
- Vol. 4 (1) , 1-31
Enhancing tribological properties of MoS2 coatings through doping: a review of mechanisms and applications
- 19 May 2025
- Published by Springer Nature in Discover Mechanical Engineering
- Vol. 4 (1) , 1-31
Open AccessEnhancing tribological properties of MoS2 coatings through doping: a review of mechanisms and applications