Thomas D'HOndt
Research Subjects
Thomas D'HOndt has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Bart Forrier
Siemens Industry Software NV
2 shared publications - Basilio Lenzo
University of Padova
1 shared publication Enrico Risaliti
TSVT division, Siemens Digital Industries Software, Leuven, Belgium
1 shared publication- Erik Wilhelm
Singapore University of Technology and Design
1 shared publication - Lorenzo Berzi
Department of Industrial Engineering, University of Florence, via di S. Marta 3, 50139 Florence, Italy
1 shared publication - Luca Pugi
University of Florence
1 shared publication
Latest Publications
- 9 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 73 (4) , 4683-4693
Hardware-in-the-Loop Real-Time Implementation of a Vehicle Stability Control Through Individual Wheel Torques
The enhancement of vehicle passenger safety is a central theme for car manufacturers. Since the introduction of Electronic Stability Control (ESC) in the late 90s, researchers in industry and academia have kept striving for continuously enhancing vehicle safety. However, despite significant efforts, the literature shows that a significant number of these endeavors have not advanced beyond theoretical formulations and software simulations. This paper presents the testing journey of an individual-wheel-torque-based vehicle stability controller through the major milestones of its development cycle. First, the controller is formulated based on specific vehicle dynamics design requirements. Then, an offline co-simulation is put in place to validate the controller along relevant maneuvers, with the controller running on Matlab-Simulink concurrently with the software Amesim running a 15-dof vehicle model of Siemens' SimRod battery electric vehicle. Next, a real-time co-simulation is achieved, running both the controller and the vehicle model on a real-time platform. Finally, an experimental hardware-in-the-loop setup is built, incorporating a dedicated Electronic Control Unit (ECU), and successfully tested.
- 9 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 73 (4) , 4683-4693
Hardware-in-the-Loop Real-Time Implementation of a Vehicle Stability Control Through Individual Wheel Torques
The enhancement of vehicle passenger safety is a central theme for car manufacturers. Since the introduction of Electronic Stability Control (ESC) in the late 90s, researchers in industry and academia have kept striving for continuously enhancing vehicle safety. However, despite significant efforts, the literature shows that a significant number of these endeavors have not advanced beyond theoretical formulations and software simulations. This paper presents the testing journey of an individual-wheel-torque-based vehicle stability controller through the major milestones of its development cycle. First, the controller is formulated based on specific vehicle dynamics design requirements. Then, an offline co-simulation is put in place to validate the controller along relevant maneuvers, with the controller running on Matlab-Simulink concurrently with the software Amesim running a 15-dof vehicle model of Siemens' SimRod battery electric vehicle. Next, a real-time co-simulation is achieved, running both the controller and the vehicle model on a real-time platform. Finally, an experimental hardware-in-the-loop setup is built, incorporating a dedicated Electronic Control Unit (ECU), and successfully tested.
- Open Access
- 14 April 2020
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Modeling and Identification of an Electric Vehicle Braking System: Thermal and Tribology Phenomena Assessment
A rapidly shifting market and increasingly stringent environmental regulations require the automotive industry to produce more efficient low-emission Electric Vehicles (EVs). Regenerative braking has proven to be a major contributor to both objectives, enabling the charging of the batteries during braking and a reduction of the load and wear of the brake pads. The optimal sizing of such systems requires the availability of good simulation models to improve their performance and reliability at all stages of the vehicle design. This enables the designer to study both the integration of the braking system with the full vehicle equipment and the interactions between electrical and mechanical braking strategies. This paper presents a generic simulation framework for the identification of thermal and wear behaviour of a mechanical braking system, based on a lumped parameter approach. The thermal behaviour of the system is coupled back to the friction coefficient between the pad and the disk to assess its effect on braking performance. Additionally, the effect of wear and temperature on the generation of airborne particles is investigated. Subsequently, experimental data collected on a real EV is used to validate and tune the previously described simulation model, following a proposed validation procedure. The instrumentation method and challenges, as well as the experimental procedure used to collect the data on a chassis dynamometer and in real-world driving conditions, are described. Finally, simulation results for different driving scenarios are used to compare virtual and experimental results.
- 14 April 2020
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Open AccessModeling and Identification of an Electric Vehicle Braking System: Thermal and Tribology Phenomena Assessment
A rapidly shifting market and increasingly stringent environmental regulations require the automotive industry to produce more efficient low-emission Electric Vehicles (EVs). Regenerative braking has proven to be a major contributor to both objectives, enabling the charging of the batteries during braking and a reduction of the load and wear of the brake pads. The optimal sizing of such systems requires the availability of good simulation models to improve their performance and reliability at all stages of the vehicle design. This enables the designer to study both the integration of the braking system with the full vehicle equipment and the interactions between electrical and mechanical braking strategies. This paper presents a generic simulation framework for the identification of thermal and wear behaviour of a mechanical braking system, based on a lumped parameter approach. The thermal behaviour of the system is coupled back to the friction coefficient between the pad and the disk to assess its effect on braking performance. Additionally, the effect of wear and temperature on the generation of airborne particles is investigated. Subsequently, experimental data collected on a real EV is used to validate and tune the previously described simulation model, following a proposed validation procedure. The instrumentation method and challenges, as well as the experimental procedure used to collect the data on a chassis dynamometer and in real-world driving conditions, are described. Finally, simulation results for different driving scenarios are used to compare virtual and experimental results.