Szymon Wyrąbkiewicz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Szymon Wyrąbkiewicz has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Maciej Gajewski
Faculty of Mechanical Engineering, Bydgoszcz University of Science and Technology, Al. prof. S. Kaliskiego 7, 85-796 Bydgoszcz, Poland
4 shared publications - Jerzy Kaszkowiak
Department of Mechanical Engineering, Bydgoszcz University of Science and Technology, Al. Prof. S. Kaliskiego 7, 85-796 Bydgoszcz, Poland
3 shared publications - Marcin Zastempowski
Faculty of Mechanical Engineering, Bydgoszcz University of Science and Technology, Al. prof. S. Kaliskiego 7, 85-796 Bydgoszcz, Poland
3 shared publications - Andrzej Bochat
Faculty of Mechanical Engineering, Bydgoszcz University of Science and Technology, Al. prof. S. Kaliskiego 7, 85-796 Bydgoszcz, Poland
1 shared publication - Jurand Burczyński
Department of Mechanical Engineering, Mechatronics and Working Machines, Jan and Jędrzej Śniadecki University of Technology in Bydgoszcz, 85-796 Bydgoszcz, Poland
1 shared publication - Karol Lisiecki
Department of Microbiology and Plant Ecology, Faculty of Agriculture and Biotechnology, Bydgoszcz University of Science and Technology, Kaliskiego 7, 85-796 Bydgoszcz, Poland
1 shared publication
Latest Publications
- Open Access
- 21 September 2026
- Published by MDPI AG in Sustainability
- Vol. 18 (18) , 9678
Directions of Development of Sustainable Maize Protection Under Conditions of Increasing Pressure from the Ostrinia nubilalis Pest—Preliminary Studies
The article presents the results of research conducted at Bydgoszcz University of Science and Technology concerning the abundance of a serious maize pest—the European corn borer-Ostrinia nubilalis Hbn (O. nubilalis). The study focused on the actual occurrence of this pest in maize stubble grown after different forecrop and among different maize cultivars. Our research fits perfectly within the framework of Integrated Pest Management (IPM) and is important because feeding by the European corn borer increasingly leads to substantial yield losses. From a sustainability perspective, knowledge of larval abundance and vertical distribution may support the development of targeted non-chemical control measures that complement existing Integrated Pest Management strategies. For the purposes of this study, maize was harvested for green fodder in September and for grain in November 2025. It was found that up to three pest larvae were present in some stubbles. On average, for every 25 plants analyzed at stubble grain harvest, over 30 larvae were found inside the stems—some contained as few as three larvae. It was found that the forecrop did not significantly affect larval abundance, whereas cultivar characteristics were the key factor differentiating their occurrence. The results of this study indicate that maize growers should pay increasing attention to this serious pest and strive for its more effective control, particularly through the use of the numerous available non-chemical methods for regulating its population. A patented design solution developed by the authors for the mechanical reduction in O. nubilalis abundance may also be helpful in this regard.
- 21 September 2026
- Published by MDPI AG in Sustainability
- Vol. 18 (18) , 9678
Open AccessDirections of Development of Sustainable Maize Protection Under Conditions of Increasing Pressure from the Ostrinia nubilalis Pest—Preliminary Studies
The article presents the results of research conducted at Bydgoszcz University of Science and Technology concerning the abundance of a serious maize pest—the European corn borer-Ostrinia nubilalis Hbn (O. nubilalis). The study focused on the actual occurrence of this pest in maize stubble grown after different forecrop and among different maize cultivars. Our research fits perfectly within the framework of Integrated Pest Management (IPM) and is important because feeding by the European corn borer increasingly leads to substantial yield losses. From a sustainability perspective, knowledge of larval abundance and vertical distribution may support the development of targeted non-chemical control measures that complement existing Integrated Pest Management strategies. For the purposes of this study, maize was harvested for green fodder in September and for grain in November 2025. It was found that up to three pest larvae were present in some stubbles. On average, for every 25 plants analyzed at stubble grain harvest, over 30 larvae were found inside the stems—some contained as few as three larvae. It was found that the forecrop did not significantly affect larval abundance, whereas cultivar characteristics were the key factor differentiating their occurrence. The results of this study indicate that maize growers should pay increasing attention to this serious pest and strive for its more effective control, particularly through the use of the numerous available non-chemical methods for regulating its population. A patented design solution developed by the authors for the mechanical reduction in O. nubilalis abundance may also be helpful in this regard.
- Open Access
Emissions and Particulate Characteristics of Spark-Ignition Engines Fueled with Bioethanol–Gasoline Blends
This article presents the results of research on the effects of various bioethanol concentrations in gasoline blends (E0, E10, E30, E50, E100) and increased fuel dosage (+10% and +20%) on spark-ignition engine performance and exhaust emissions. Experiments were conducted on a chassis dynamometer under strictly controlled laboratory conditions using a MAHA MGT-5 exhaust gas analyzer and a MAHA MPM-4 particulate matter analyzer. Power, torque, carbon monoxide (CO), carbon dioxide (CO2), hydrocarbons (HC), oxygen (O2), and particulate matter emissions were analyzed. It was found that up to a 50% bioethanol content, power and torque remained stable, while with E100, a significant decrease in these parameters was observed, partially offset by the increased fuel dosage. CO emissions systematically decreased with increasing bioethanol content, reaching minimum values at E100, while HC emissions generally decreased. CO2 content did not show clear trends, while O2 levels in the exhaust gas increased with higher ethanol concentrations. Particulate matter emissions were irregular, with the lowest values at E30 for the nominal dose and at E10 for the increased dose. The studies revealed significant nonlinearities in the effect of ethanol concentration on emissions, challenging the common assumption of monotonic changes. The results have practical implications for optimizing the calibration of engine control systems, meeting emission standards, and assessing the potential of bioethanol as a road transport fuel.
Open AccessEmissions and Particulate Characteristics of Spark-Ignition Engines Fueled with Bioethanol–Gasoline Blends
This article presents the results of research on the effects of various bioethanol concentrations in gasoline blends (E0, E10, E30, E50, E100) and increased fuel dosage (+10% and +20%) on spark-ignition engine performance and exhaust emissions. Experiments were conducted on a chassis dynamometer under strictly controlled laboratory conditions using a MAHA MGT-5 exhaust gas analyzer and a MAHA MPM-4 particulate matter analyzer. Power, torque, carbon monoxide (CO), carbon dioxide (CO2), hydrocarbons (HC), oxygen (O2), and particulate matter emissions were analyzed. It was found that up to a 50% bioethanol content, power and torque remained stable, while with E100, a significant decrease in these parameters was observed, partially offset by the increased fuel dosage. CO emissions systematically decreased with increasing bioethanol content, reaching minimum values at E100, while HC emissions generally decreased. CO2 content did not show clear trends, while O2 levels in the exhaust gas increased with higher ethanol concentrations. Particulate matter emissions were irregular, with the lowest values at E30 for the nominal dose and at E10 for the increased dose. The studies revealed significant nonlinearities in the effect of ethanol concentration on emissions, challenging the common assumption of monotonic changes. The results have practical implications for optimizing the calibration of engine control systems, meeting emission standards, and assessing the potential of bioethanol as a road transport fuel.
- Open Access
Effects of Ethanol–Gasoline Blends on the Performance and Emissions of a Vehicle Spark-Ignition Engine
This article presents experimental results related to the influence of bioethanol content in fuel blends on the performance and emissions of a spark-ignition engine. Tests were conducted for six ethanol–gasoline mixtures (ranging from 0% to 100% ethanol) under three engine control strategies: factory settings, a fuel dose increased by 10%, and a fuel dose increased by 20%—both with an ignition timing adjustment of +3°. Measurements included engine power and torque, as well as emissions of CO, CO2, HC, O2, and particulate matter, all performed under a full engine load. The results revealed the strong dependence of engine behavior on ethanol content. Increasing the ethanol concentration significantly reduced CO and HC emissions, as well as markedly lowering particulate emissions—particularly at 30% ethanol. Conversely, pure ethanol led to substantial reductions in power (up to 28%) and torque (up to 32%) compared to conventional gasoline. Adjustments to the fuel dose and ignition timing partially mitigated these losses. Emissions of CO2 and oxygen content in exhaust gases varied depending on the blend, highlighting the complex nature of the combustion process. The findings contribute to the understanding of renewable fuel behavior in SI engines and underscore the influence of both fuel composition and control strategies on performance and emission characteristics.
Open AccessEffects of Ethanol–Gasoline Blends on the Performance and Emissions of a Vehicle Spark-Ignition Engine
This article presents experimental results related to the influence of bioethanol content in fuel blends on the performance and emissions of a spark-ignition engine. Tests were conducted for six ethanol–gasoline mixtures (ranging from 0% to 100% ethanol) under three engine control strategies: factory settings, a fuel dose increased by 10%, and a fuel dose increased by 20%—both with an ignition timing adjustment of +3°. Measurements included engine power and torque, as well as emissions of CO, CO2, HC, O2, and particulate matter, all performed under a full engine load. The results revealed the strong dependence of engine behavior on ethanol content. Increasing the ethanol concentration significantly reduced CO and HC emissions, as well as markedly lowering particulate emissions—particularly at 30% ethanol. Conversely, pure ethanol led to substantial reductions in power (up to 28%) and torque (up to 32%) compared to conventional gasoline. Adjustments to the fuel dose and ignition timing partially mitigated these losses. Emissions of CO2 and oxygen content in exhaust gases varied depending on the blend, highlighting the complex nature of the combustion process. The findings contribute to the understanding of renewable fuel behavior in SI engines and underscore the influence of both fuel composition and control strategies on performance and emission characteristics.
- Open Access
- 29 May 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (11) , 6146
Analysis of Selected Methods of Computer-Aided Design for Stage Structures
This article presents the design process for a modern stage trapdoor, which was designed to optimize the work of cultural facilities personnel and increase the attractiveness of future performances and events. Strength calculations for the supporting structure were carried out in the Soldis DESIGNER program, and based on these, a 3D model of the stage trapdoor was designed and placed in the space of the stage chimney. In order to verify and analyze the strength of the structure, the 3D model was prepared for detailed analysis in the Autodesk Inventor program. Tests were carried out for four load cases of the structure for 15 different load values. Information about the maximum value of the deflection arrow and the maximum stress was obtained. Collected data were organized in tables and displayed in line and column charts, based on which conclusions were drawn. These analyses showed a high degree of compliance between calculations from both programs. It was found that in this type of structure, a detailed analysis in 3D CAD programs is not necessary for the proper design of the supporting structure, which allows for simplification of the design process. The designed trapdoor meets all design requirements and can be implemented as a solution to improve the functionality and aesthetics of the stage’s technical equipment.
- 29 May 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (11) , 6146
Open AccessAnalysis of Selected Methods of Computer-Aided Design for Stage Structures
This article presents the design process for a modern stage trapdoor, which was designed to optimize the work of cultural facilities personnel and increase the attractiveness of future performances and events. Strength calculations for the supporting structure were carried out in the Soldis DESIGNER program, and based on these, a 3D model of the stage trapdoor was designed and placed in the space of the stage chimney. In order to verify and analyze the strength of the structure, the 3D model was prepared for detailed analysis in the Autodesk Inventor program. Tests were carried out for four load cases of the structure for 15 different load values. Information about the maximum value of the deflection arrow and the maximum stress was obtained. Collected data were organized in tables and displayed in line and column charts, based on which conclusions were drawn. These analyses showed a high degree of compliance between calculations from both programs. It was found that in this type of structure, a detailed analysis in 3D CAD programs is not necessary for the proper design of the supporting structure, which allows for simplification of the design process. The designed trapdoor meets all design requirements and can be implemented as a solution to improve the functionality and aesthetics of the stage’s technical equipment.