Yong Cao
Yong Cao has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Wei Qi
Sichuan Provincial Engineering Research Center of Rail Transit Lines Smart Operation and Maintenance, Chengdu Vocational & Technical College of Industry, Chengdu 610213, China
3 shared publications - Ge Yang
MOE Key Laboratory of High-speed Railway Engineering, School of Civil Engineering, Southwest Jiaotong University, Chengdu 610031, China
2 shared publications - Jianbiao Du
MOE Key Laboratory of High-speed Railway Engineering, School of Civil Engineering, Southwest Jiaotong University, Chengdu 610031, China
2 shared publications - Tengfei Wang
MOE Key Laboratory of High-speed Railway Engineering, School of Civil Engineering, Southwest Jiaotong University, Chengdu 610031, China
2 shared publications - Aiping Chen
Sichuan Provincial Engineering Research Center of Rail Transit Lines Smart Operation and Maintenance, Chengdu Vocational & Technical College of Industry, Chengdu 610213, China
1 shared publication - Feiyang Liu
MOE Key Laboratory of High-speed Railway Engineering, School of Civil Engineering, Southwest Jiaotong University, Chengdu 610031, China
1 shared publication
Latest Publications
- Open Access
Mix Proportion Optimization of Loess-Based Controlled Low-Strength Material Considering Field Water-to-Solids Ratio Uncertainty
Loess is highly water-sensitive and collapsible, and its conventional use as backfill in road and railway infrastructure may lead to settlement and deformation after wetting. Converting excavated loess into controlled low-strength material (CLSM) provides an alternative for backfilling; however, its engineering performance is strongly dependent on the water-to-solids ratio (W). In field construction, variations in the natural moisture content of loess cause the actual W to deviate from its design value, whereas conventional CLSM mix designs generally assume a fixed W, which may result in insufficient flowability or strength under actual field conditions. A Box–Behnken design was first employed to investigate the effects of the cement-to-soil ratio (C), water-to-solids ratio (W), and polycarboxylate superplasticizer content (P) on flowability (f), bleeding rate (Bᵥ), wet density (ρ), and 28-day compressive strength (qᵤ), based on which regression-based predictive models were developed. The sequential least squares programming (SLSQP) algorithm was then used to optimize mix proportions for backfilling behind abutments, culverts, and retaining walls and for subgrade backfilling. The optimization minimized the material cost per unit volume while requiring all performance indicators to satisfy the specified criteria under variations in W (ΔW = 0%, ±1%, ±2%, and ±3%). The results show that W is the dominant factor governing f, Bᵥ, and ρ, whereas C has the greatest influence on qᵤ. Increasing P markedly improves f but also increases Bᵥ. For backfilling behind abutments, culverts, and retaining walls, when the mean field soil moisture content is overestimated and the actual W is consequently lower than its design value, the mix optimized for ΔW = −3% satisfies the flowability criterion even when the measured flowability is up to 21.3 mm below the design value because of the lower actual soil moisture content. Conversely, when the mean field soil moisture content is underestimated and the actual W exceeds its design value, the mix optimized for ΔW = +3% satisfies the compressive-strength criterion even when the measured strength is up to 0.09 MPa below the design value because of the higher actual soil moisture content. Accounting for possible variations of up to ±3% in the water-to-solids ratio under field conditions, the optimal mix proportions are C13.14W37.64P0.069 for backfilling behind abutments, culverts, and retaining walls and C15.00W34.28P0.097 for subgrade backfilling. These findings provide a basis for the performance control and mix design of loess-based CLSM subjected to variations in the water-to-solids ratio.
Open AccessMix Proportion Optimization of Loess-Based Controlled Low-Strength Material Considering Field Water-to-Solids Ratio Uncertainty
Loess is highly water-sensitive and collapsible, and its conventional use as backfill in road and railway infrastructure may lead to settlement and deformation after wetting. Converting excavated loess into controlled low-strength material (CLSM) provides an alternative for backfilling; however, its engineering performance is strongly dependent on the water-to-solids ratio (W). In field construction, variations in the natural moisture content of loess cause the actual W to deviate from its design value, whereas conventional CLSM mix designs generally assume a fixed W, which may result in insufficient flowability or strength under actual field conditions. A Box–Behnken design was first employed to investigate the effects of the cement-to-soil ratio (C), water-to-solids ratio (W), and polycarboxylate superplasticizer content (P) on flowability (f), bleeding rate (Bᵥ), wet density (ρ), and 28-day compressive strength (qᵤ), based on which regression-based predictive models were developed. The sequential least squares programming (SLSQP) algorithm was then used to optimize mix proportions for backfilling behind abutments, culverts, and retaining walls and for subgrade backfilling. The optimization minimized the material cost per unit volume while requiring all performance indicators to satisfy the specified criteria under variations in W (ΔW = 0%, ±1%, ±2%, and ±3%). The results show that W is the dominant factor governing f, Bᵥ, and ρ, whereas C has the greatest influence on qᵤ. Increasing P markedly improves f but also increases Bᵥ. For backfilling behind abutments, culverts, and retaining walls, when the mean field soil moisture content is overestimated and the actual W is consequently lower than its design value, the mix optimized for ΔW = −3% satisfies the flowability criterion even when the measured flowability is up to 21.3 mm below the design value because of the lower actual soil moisture content. Conversely, when the mean field soil moisture content is underestimated and the actual W exceeds its design value, the mix optimized for ΔW = +3% satisfies the compressive-strength criterion even when the measured strength is up to 0.09 MPa below the design value because of the higher actual soil moisture content. Accounting for possible variations of up to ±3% in the water-to-solids ratio under field conditions, the optimal mix proportions are C13.14W37.64P0.069 for backfilling behind abutments, culverts, and retaining walls and C15.00W34.28P0.097 for subgrade backfilling. These findings provide a basis for the performance control and mix design of loess-based CLSM subjected to variations in the water-to-solids ratio.
- Open Access
Engineering Performance of Expansive Soil Stabilized with Cement and Montmorillonite Adsorption Modifier
To enhance the strength and water stability of stabilized expansive soil, this study investigates the use of cement, montmorillonite adsorption modifier (MAM), and their composite system. Laboratory tests evaluated compaction characteristics, swell–shrink behavior, and mechanical performance. The results show that MAM more effectively regulates compaction by reducing optimum water content and increasing maximum dry density; 6% MAM increases maximum dry density by ≈0.04 g/cm3 and reduces optimum water content by ≈2%. In terms of swell–shrink behavior, MAM reduces both swelling and linear shrinkage more effectively than cement. The incorporation of 5% MAM reduces the free swelling ratio by 40% and the equilibrium moisture absorption by 2.7%, lowering the swelling classification to non-expansive. Furthermore, 5% MAM decreases the unloaded and loaded swelling ratio by 14.7% and 5%, respectively, while increasing MAM from 2% to 6% further reduces linear shrinkage by 1.12%. Cement significantly enhances compressive strength, with 7–28 d values reaching 2.2–2.7 times those of untreated soil at 9% content; however, its water stability under wet–dry cycles is limited. In contrast, the cement–MAM composite system achieves balanced improvement by simultaneously suppressing swelling and enhancing both strength and water stability. These findings provide a reference for the treatment and engineering application of expansive soils.
Open AccessEngineering Performance of Expansive Soil Stabilized with Cement and Montmorillonite Adsorption Modifier
To enhance the strength and water stability of stabilized expansive soil, this study investigates the use of cement, montmorillonite adsorption modifier (MAM), and their composite system. Laboratory tests evaluated compaction characteristics, swell–shrink behavior, and mechanical performance. The results show that MAM more effectively regulates compaction by reducing optimum water content and increasing maximum dry density; 6% MAM increases maximum dry density by ≈0.04 g/cm3 and reduces optimum water content by ≈2%. In terms of swell–shrink behavior, MAM reduces both swelling and linear shrinkage more effectively than cement. The incorporation of 5% MAM reduces the free swelling ratio by 40% and the equilibrium moisture absorption by 2.7%, lowering the swelling classification to non-expansive. Furthermore, 5% MAM decreases the unloaded and loaded swelling ratio by 14.7% and 5%, respectively, while increasing MAM from 2% to 6% further reduces linear shrinkage by 1.12%. Cement significantly enhances compressive strength, with 7–28 d values reaching 2.2–2.7 times those of untreated soil at 9% content; however, its water stability under wet–dry cycles is limited. In contrast, the cement–MAM composite system achieves balanced improvement by simultaneously suppressing swelling and enhancing both strength and water stability. These findings provide a reference for the treatment and engineering application of expansive soils.
- Open Access
Hydraulic Design Strategies for Resilient Slab Track Under Extreme Rainfall Events
Extreme rainfall events pose a growing threat to slab track subgrades by triggering mud pumping through fines migration and structural voids. This study introduces two innovations to enhance climate resilience in high-speed railway infrastructure: (i) the Rain Intensity Ponding (RIP) method, which links regional rainfall statistics with axle-pass thresholds to predict mud pumping potential; (ii) an optimized drainage retrofit using permeable shoulders and blind ditches. Physical model tests reveal that mud pumping occurs only when structural gaps, ponding, and cyclic loading coincide. The RIP method correctly identified a 71% exceedance in the critical ponding duration (52 min) on a representative high-speed line in Eastern China, explaining recurrent failures. Parametric analyses show that the proposed drainage retrofit—using shoulder fill with ka > 23 mm/s and blind ditches with kg > 23 mm/s—reduces ponding time by up to 90% under 1-year recurrence storms. This study establishes a physics-based, region-specific strategy for mud pumping mitigation, offering guidance for climate-adaptive slab track design and operation.
Open AccessHydraulic Design Strategies for Resilient Slab Track Under Extreme Rainfall Events
Extreme rainfall events pose a growing threat to slab track subgrades by triggering mud pumping through fines migration and structural voids. This study introduces two innovations to enhance climate resilience in high-speed railway infrastructure: (i) the Rain Intensity Ponding (RIP) method, which links regional rainfall statistics with axle-pass thresholds to predict mud pumping potential; (ii) an optimized drainage retrofit using permeable shoulders and blind ditches. Physical model tests reveal that mud pumping occurs only when structural gaps, ponding, and cyclic loading coincide. The RIP method correctly identified a 71% exceedance in the critical ponding duration (52 min) on a representative high-speed line in Eastern China, explaining recurrent failures. Parametric analyses show that the proposed drainage retrofit—using shoulder fill with ka > 23 mm/s and blind ditches with kg > 23 mm/s—reduces ponding time by up to 90% under 1-year recurrence storms. This study establishes a physics-based, region-specific strategy for mud pumping mitigation, offering guidance for climate-adaptive slab track design and operation.