Shuoyan Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shuoyan Zhang has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Xiaolong Chen
School of Mechano-Electronic Engineering, Xidian University, Xi’an 710071, China
4 shared publications - Haoyu Yu
State Key Laboratory of Electromechanical Integrated Manufacturing of High-performance Electronic Equipments, Xidian University, Xian, China
3 shared publications - Zanyu Shang
State Key Laboratory of Electromechanical Integrated Manufacturing of High-performance Electronic Equipment, Xidian University, Xian, China
3 shared publications - Huiting Huan
School of Mechano-Electronic Engineering, Xidian University, Xi’an 710071, China
2 shared publications - Xing Quan
School of Mechano-Electronic Engineering, Xidian University, Xian, China
2 shared publications - Haiqing Zhang
Ceyear Technologies Co., Ltd., Qingdao, China
1 shared publication
Latest Publications
- 1 October 2026
- Published by Elsevier in Measurement
- Vol. 292
A Jitter Measurement Method without Predefined Test Patterns Robust to ISI Effects for Serial Links
- 1 October 2026
- Published by Elsevier in Measurement
- Vol. 292
A Jitter Measurement Method without Predefined Test Patterns Robust to ISI Effects for Serial Links
- 4 September 2026
- Published by Elsevier in Measurement
- Vol. 290
Fast-converging time-domain adaptive reconstruction for sinusoidal signal under short-time sampling and spectral leakage
- 4 September 2026
- Published by Elsevier in Measurement
- Vol. 290
Fast-converging time-domain adaptive reconstruction for sinusoidal signal under short-time sampling and spectral leakage
- 8 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 75 (00189456) , 2003407
Spectral Estimation of Discrete Sampling Jitter Sequences in PLL-Based Clocking Chains
Sampling clock jitter is a dominant factor limiting the dynamic performance of high-speed analog-to-digital converters (ADCs). Its impact on the signal-to-noise ratio (SNR) increases with input frequency. Existing jitter characterization methods face a dual challenge when applied to ADC sampling: (i) the sampling jitter manifests as a discrete-time sequence, and (ii) its power spectral density (PSD) distribution over the entire observation frequency range is not mathematically clear. In this paper, sampling jitter is modeled as the periodic sampling of continuous-time jitter from a physical perspective. Considering phase-locked loop (PLL)-based clock generation chains, the theoretical relationship among phase noise, time jitter, and sampling jitter is established to derive the sampling jitter PSD. The proposed theoretical model is tested on a practical clocking chain. For clock frequencies ranging from 200 MHz to 600 MHz, the root mean square (RMS) and maximum error bar of the mean squared errors (MSEs) between the measured results and the theoretical prediction are 0.23 dB and 0.63 dB, respectively.
- 8 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 75 (00189456) , 2003407
Spectral Estimation of Discrete Sampling Jitter Sequences in PLL-Based Clocking Chains
Sampling clock jitter is a dominant factor limiting the dynamic performance of high-speed analog-to-digital converters (ADCs). Its impact on the signal-to-noise ratio (SNR) increases with input frequency. Existing jitter characterization methods face a dual challenge when applied to ADC sampling: (i) the sampling jitter manifests as a discrete-time sequence, and (ii) its power spectral density (PSD) distribution over the entire observation frequency range is not mathematically clear. In this paper, sampling jitter is modeled as the periodic sampling of continuous-time jitter from a physical perspective. Considering phase-locked loop (PLL)-based clock generation chains, the theoretical relationship among phase noise, time jitter, and sampling jitter is established to derive the sampling jitter PSD. The proposed theoretical model is tested on a practical clocking chain. For clock frequencies ranging from 200 MHz to 600 MHz, the root mean square (RMS) and maximum error bar of the mean squared errors (MSEs) between the measured results and the theoretical prediction are 0.23 dB and 0.63 dB, respectively.
- 23 February 2026
- Published by Elsevier in Measurement
- Vol. 270
High-speed ADC clock jitter measurement and compensation algorithm for the mid- and high-frequency sampling region
- 23 February 2026
- Published by Elsevier in Measurement
- Vol. 270
High-speed ADC clock jitter measurement and compensation algorithm for the mid- and high-frequency sampling region
- 3 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-8
A Cyclostationarity-Based Method for Time Interval Error Extraction Without Clock Recovery in SerDes Links
Precise jitter identification and extraction are critical for jitter decomposition, fault diagnosis, and bit error rate estimation in high-speed serial communications. Conventional methods depend on decision threshold and clock recovery, which discard significant signal information, as only threshold crossing points are considered. Additionally, the accuracy of jitter extraction is sensitive to errors introduced by histogram-based statistical computations and interpolation processes. This paper presents a novel jitter extraction method based on a signal transmission model that fully exploits the cyclostationary characteristics of the signal. By utilizing all signal points rather than just threshold crossings, this method eliminates the presetting modules and avoids statistical computations or interpolations, resulting in a simpler implementation and lower complexity. A theoretical model is developed to demonstrate that the phase of the cyclic autocorrelation function at the symbol rate frequency intrinsically encodes the jitter information for each symbol. The time interval error jitter can be extracted by computing the phase via the fast Fourier transform, followed by least squares correction to eliminate cumulative errors. Simulations under various jitter conditions validate the accuracy and robustness of the proposed method, showing comparable performance to conventional approaches while achieving superior accuracy in sinusoidal jitter scenarios. The effectiveness is further demonstrated through oscilloscope experiments, with relative errors below 1%, confirming its accuracy and practical applicability.
- 3 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-8
A Cyclostationarity-Based Method for Time Interval Error Extraction Without Clock Recovery in SerDes Links
Precise jitter identification and extraction are critical for jitter decomposition, fault diagnosis, and bit error rate estimation in high-speed serial communications. Conventional methods depend on decision threshold and clock recovery, which discard significant signal information, as only threshold crossing points are considered. Additionally, the accuracy of jitter extraction is sensitive to errors introduced by histogram-based statistical computations and interpolation processes. This paper presents a novel jitter extraction method based on a signal transmission model that fully exploits the cyclostationary characteristics of the signal. By utilizing all signal points rather than just threshold crossings, this method eliminates the presetting modules and avoids statistical computations or interpolations, resulting in a simpler implementation and lower complexity. A theoretical model is developed to demonstrate that the phase of the cyclic autocorrelation function at the symbol rate frequency intrinsically encodes the jitter information for each symbol. The time interval error jitter can be extracted by computing the phase via the fast Fourier transform, followed by least squares correction to eliminate cumulative errors. Simulations under various jitter conditions validate the accuracy and robustness of the proposed method, showing comparable performance to conventional approaches while achieving superior accuracy in sinusoidal jitter scenarios. The effectiveness is further demonstrated through oscilloscope experiments, with relative errors below 1%, confirming its accuracy and practical applicability.