Seungchan Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Seungchan Lee has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Myungsoo Kim
Graduate School of Semiconductor Materials and Devices Engineering Ulsan National Institute of Science and Technology (UNIST) Ulsan South Korea
6 shared publications - Changwoo Pyo
Graduate School of Semiconductor Materials and Devices Engineering Ulsan National Institute of Science and Technology (UNIST) Ulsan 44919 South Korea
4 shared publications - Sungmoon Park
Graduate School of Semiconductor Materials and Devices Engineering Ulsan National Institute of Science and Technology (UNIST) Ulsan Republic of Korea
4 shared publications - Dabin Seo
Graduate School of Semiconductor Materials and Devices Engineering Ulsan National Institute of Science and Technology (UNIST) Ulsan Republic of Korea
2 shared publications Dohyun Lee
School of Advanced Materials Science and Engineering, Sungkyunkwan University (SKKU), Suwon, Republic of Korea
2 shared publications- Heein Yoon
Department of Electrical Engineering, Ulsan National Institute of Science and Technology, Ulsan, South Korea
2 shared publications
Latest Publications
Monolayer h‐BN RF Switch Toward Monolithic Inductor Switching in Wide‐Tuning‐Range LC ‐VCOs
Next‐generation wireless systems demand monolithic three‐dimensional (3D) system‐on‐chip architectures to overcome planar scaling limits and reduce interconnect delays. Realizing this back‐end‐of‐line (BEOL) integration on complementary metal‐oxide‐semiconductor (CMOS) platforms requires ultracompact, high‐performance radio‐frequency (RF) switches. Here, we present a non‐volatile RF switch based on a monolayer hexagonal boron nitride (h‐BN) memristor employing an Ag/h‐BN/Ag structure. The device exhibits a low SET voltage of 1.11 V and stable endurance exceeding 500 cycles. At 20 GHz, it achieves an insertion loss of 0.81 dB and an isolation of 32.91 dB, enabled by a low on‐resistance ( R ON ) of 4.3 Ω and an ultralow off‐capacitance ( C OFF ) of 1.8 fF, corresponding to a cut‐off frequency ( F CO ) of 20.5 THz. To verify its feasibility at the circuit level, the h‐BN RF switch was applied to an LC ‐type voltage‐controlled oscillator ( LC ‐VCO), whose inductance can be reconfigured. The simulation results indicate that modulating the switch state and thereby changing the effective inductance enables wideband frequency tuning from 1.44 to 7.45 GHz, corresponding to a frequency tuning range (FTR) of 135%. These results verify the feasibility of the atomically thin h‐BN RF switch for inductor switching in reconfigurable LC ‐VCOs, presenting a promising route toward miniaturized high‐frequency circuit designs.
Monolayer h‐BN RF Switch Toward Monolithic Inductor Switching in Wide‐Tuning‐Range LC ‐VCOs
Next‐generation wireless systems demand monolithic three‐dimensional (3D) system‐on‐chip architectures to overcome planar scaling limits and reduce interconnect delays. Realizing this back‐end‐of‐line (BEOL) integration on complementary metal‐oxide‐semiconductor (CMOS) platforms requires ultracompact, high‐performance radio‐frequency (RF) switches. Here, we present a non‐volatile RF switch based on a monolayer hexagonal boron nitride (h‐BN) memristor employing an Ag/h‐BN/Ag structure. The device exhibits a low SET voltage of 1.11 V and stable endurance exceeding 500 cycles. At 20 GHz, it achieves an insertion loss of 0.81 dB and an isolation of 32.91 dB, enabled by a low on‐resistance ( R ON ) of 4.3 Ω and an ultralow off‐capacitance ( C OFF ) of 1.8 fF, corresponding to a cut‐off frequency ( F CO ) of 20.5 THz. To verify its feasibility at the circuit level, the h‐BN RF switch was applied to an LC ‐type voltage‐controlled oscillator ( LC ‐VCO), whose inductance can be reconfigured. The simulation results indicate that modulating the switch state and thereby changing the effective inductance enables wideband frequency tuning from 1.44 to 7.45 GHz, corresponding to a frequency tuning range (FTR) of 135%. These results verify the feasibility of the atomically thin h‐BN RF switch for inductor switching in reconfigurable LC ‐VCOs, presenting a promising route toward miniaturized high‐frequency circuit designs.
- Open Access
- 21 October 2026
- Published by Wiley in Advanced Functional Materials
Low‐Flicker‐Noise MoS 2 Transistors Enabled by High‐ κ Rare‐Earth Oxychlorides for Mixed‐Signal Electronics
The trade‐off between gate dielectric constant and interface quality limits two‐dimensional (2D) analog and mixed‐signal electronics because trap‐mediated 1/ f noise from amorphous oxides degrades signal fidelity. Here, single‐crystalline rare‐earth oxychlorides (REOCl; LaOCl and GdOCl) are employed as Cl‐terminated crystalline high‐ κ dielectrics that form atomically abrupt van der Waals interfaces with MoS 2 . MoS 2 /REOCl transistors exhibit near‐thermal‐limit switching, with minimum one‐decade‐averaged subthreshold swings of 65.7 and 63.2 mV dec −1 for LaOCl and GdOCl, with ultralow hysteresis and suppressed low‐frequency noise. Carrier‐number‐fluctuation analysis of two independently measured devices per dielectric yields effective noise‐derived interface trap densities of 1.15–1.94 × 10 10 cm −2 eV −1 , approaching the hexagonal boron nitride regime while retaining high‐ κ electrostatic coupling. Channel‐area‐scaled normalized 1/ f noise remains up to two orders of magnitude below amorphous SiO 2 /Al 2 O 3 /HfO 2 controls, with on‐state S I / I D 2 reaching ∼10 −10 Hz −1 . A Samsung 28 nm high‐ κ /metal‐gate reference process design kit sensitivity analysis, with only the flicker‐noise coefficient varied, indicates reduced voltage‐controlled oscillator phase noise and phase‐locked‐loop jitter and an effective‐number‐of‐bits improvement of up to 1.45 bits in passive noise‐shaping successive‐approximation‐register analog‐to‐digital converters. These results establish REOCl as a trap‐poor high‐ κ dielectric platform for low‐noise 2D electronics and illustrate the mixed‐signal relevance of reduced transistor flicker noise.
- 21 October 2026
- Published by Wiley in Advanced Functional Materials
Open AccessLow‐Flicker‐Noise MoS 2 Transistors Enabled by High‐ κ Rare‐Earth Oxychlorides for Mixed‐Signal Electronics
The trade‐off between gate dielectric constant and interface quality limits two‐dimensional (2D) analog and mixed‐signal electronics because trap‐mediated 1/ f noise from amorphous oxides degrades signal fidelity. Here, single‐crystalline rare‐earth oxychlorides (REOCl; LaOCl and GdOCl) are employed as Cl‐terminated crystalline high‐ κ dielectrics that form atomically abrupt van der Waals interfaces with MoS 2 . MoS 2 /REOCl transistors exhibit near‐thermal‐limit switching, with minimum one‐decade‐averaged subthreshold swings of 65.7 and 63.2 mV dec −1 for LaOCl and GdOCl, with ultralow hysteresis and suppressed low‐frequency noise. Carrier‐number‐fluctuation analysis of two independently measured devices per dielectric yields effective noise‐derived interface trap densities of 1.15–1.94 × 10 10 cm −2 eV −1 , approaching the hexagonal boron nitride regime while retaining high‐ κ electrostatic coupling. Channel‐area‐scaled normalized 1/ f noise remains up to two orders of magnitude below amorphous SiO 2 /Al 2 O 3 /HfO 2 controls, with on‐state S I / I D 2 reaching ∼10 −10 Hz −1 . A Samsung 28 nm high‐ κ /metal‐gate reference process design kit sensitivity analysis, with only the flicker‐noise coefficient varied, indicates reduced voltage‐controlled oscillator phase noise and phase‐locked‐loop jitter and an effective‐number‐of‐bits improvement of up to 1.45 bits in passive noise‐shaping successive‐approximation‐register analog‐to‐digital converters. These results establish REOCl as a trap‐poor high‐ κ dielectric platform for low‐noise 2D electronics and illustrate the mixed‐signal relevance of reduced transistor flicker noise.
- Open Access
- 18 June 2026
- Published by Springer Nature in Nature Communications
- Vol. 17 (1)
Sub-femtosecond figure-of-merit millimeter-wave switches via solution-processed MoS2 for 6G radio-frequency front-ends
Next-generation 6G communication requires radio-frequency components capable of operating above 100 GHz with low loss, high isolation, and zero static power-requirements that challenge complementary metal-oxide-semiconductor (CMOS) and microelectromechanical systems (MEMS) technologies. Here, we report transfer-free, large-area millimeter-wave (mmWave) switches based on solution-processed MoS2. While solution-processed 2D materials are often viewed as inferior to their crystalline counterparts due to high defect densities, we demonstrate that their edge-rich morphology is, in fact, a performance enabler. These edge defects act as intrinsic templates that confine Cu-filament pathways, enabling rapid (76 ns) and low-energy switching (1.57 nJ) with > 2000 cycles and uniform zero static-power operation, as corroborated by Kelvin probe force microscopy, conductive atomic force microscopy and low-temperature studies. The resulting switches achieve an low insertion loss ( < 0.1 dB) and high isolation ( > 35 dB) at 67 GHz. Notably, they exhibit a switching figure-of-merit (RON·COFF) of ~ 0.8 fs (fco ~ 187 THz), surpassing previously reported 2D switches. Importantly, by adopting an inverse-state operational scheme in a SHUNT architecture, we mitigate self-switching and achieve improved power handling (P0.1dB > 10 dBm) and linearity (IIP3 > 42.1 dBm). Finally, we demonstrate the platform's circuit-level viability by integrating the switches into a true-time-delay and hybrid-coupled phase shifters targeting 30 GHz mmWave applications.
- 18 June 2026
- Published by Springer Nature in Nature Communications
- Vol. 17 (1)
Open AccessSub-femtosecond figure-of-merit millimeter-wave switches via solution-processed MoS2 for 6G radio-frequency front-ends
Next-generation 6G communication requires radio-frequency components capable of operating above 100 GHz with low loss, high isolation, and zero static power-requirements that challenge complementary metal-oxide-semiconductor (CMOS) and microelectromechanical systems (MEMS) technologies. Here, we report transfer-free, large-area millimeter-wave (mmWave) switches based on solution-processed MoS2. While solution-processed 2D materials are often viewed as inferior to their crystalline counterparts due to high defect densities, we demonstrate that their edge-rich morphology is, in fact, a performance enabler. These edge defects act as intrinsic templates that confine Cu-filament pathways, enabling rapid (76 ns) and low-energy switching (1.57 nJ) with > 2000 cycles and uniform zero static-power operation, as corroborated by Kelvin probe force microscopy, conductive atomic force microscopy and low-temperature studies. The resulting switches achieve an low insertion loss ( < 0.1 dB) and high isolation ( > 35 dB) at 67 GHz. Notably, they exhibit a switching figure-of-merit (RON·COFF) of ~ 0.8 fs (fco ~ 187 THz), surpassing previously reported 2D switches. Importantly, by adopting an inverse-state operational scheme in a SHUNT architecture, we mitigate self-switching and achieve improved power handling (P0.1dB > 10 dBm) and linearity (IIP3 > 42.1 dBm). Finally, we demonstrate the platform's circuit-level viability by integrating the switches into a true-time-delay and hybrid-coupled phase shifters targeting 30 GHz mmWave applications.
- 22 January 2026
- Published by Elsevier in Sensors and Actuators B: Chemical
- Vol. 453
Reusable RF sensor based on solution-processed MoS2 for liquid biopsy of single-stranded circulating cell-free DNA
- 22 January 2026
- Published by Elsevier in Sensors and Actuators B: Chemical
- Vol. 453
Reusable RF sensor based on solution-processed MoS2 for liquid biopsy of single-stranded circulating cell-free DNA
- 12 December 2025
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (30)
Thermally Robust Polymer‐Based Analogue Switch for Flexible mmWave Application
The realization of thermally robust, polymer‐based radio‐frequency (RF) switches for flexible millimeter‐wave (mmWave) electronics is a long‐standing challenge due to inherent material instability. Here, a novel high‐performance, thermally stable polymer‐based non‐volatile analogue switch is reported, utilizing an Au/poly(1,3,5‐trimethyl‐1,3,5‐trivinyl cyclotrisiloxane) (pV3D3)/Au memristive structure. A gold filamentary conduction model is elucidated that governs the device's resistive switching, enabling analogue switching operations. Fabricated via a wafer‐scale compatible initiated chemical vapor deposition technique, the device overcomes the limitations of prior organic electronics, exhibiting notable high‐temperature stability with a projected state retention of over 10 years at 128.7 °C and robust endurance exceeding 1600 cycles. Furthermore, the switch demonstrates excellent RF performance suitable for mmWave applications, featuring a cutoff frequency of 5.38 THz, low insertion loss (18 dB) up to 20 GHz, and stable operation up to 67 GHz. Successful implementation on a flexible substrate confirms its mechanical resilience for wearable systems. This work establishes a viable pathway for robust, polymer‐based analogue switches in advanced flexible RF technologies.
- 12 December 2025
- Published by Wiley in Advanced Functional Materials
- Vol. 36 (30)
Thermally Robust Polymer‐Based Analogue Switch for Flexible mmWave Application
The realization of thermally robust, polymer‐based radio‐frequency (RF) switches for flexible millimeter‐wave (mmWave) electronics is a long‐standing challenge due to inherent material instability. Here, a novel high‐performance, thermally stable polymer‐based non‐volatile analogue switch is reported, utilizing an Au/poly(1,3,5‐trimethyl‐1,3,5‐trivinyl cyclotrisiloxane) (pV3D3)/Au memristive structure. A gold filamentary conduction model is elucidated that governs the device's resistive switching, enabling analogue switching operations. Fabricated via a wafer‐scale compatible initiated chemical vapor deposition technique, the device overcomes the limitations of prior organic electronics, exhibiting notable high‐temperature stability with a projected state retention of over 10 years at 128.7 °C and robust endurance exceeding 1600 cycles. Furthermore, the switch demonstrates excellent RF performance suitable for mmWave applications, featuring a cutoff frequency of 5.38 THz, low insertion loss (18 dB) up to 20 GHz, and stable operation up to 67 GHz. Successful implementation on a flexible substrate confirms its mechanical resilience for wearable systems. This work establishes a viable pathway for robust, polymer‐based analogue switches in advanced flexible RF technologies.
- Open Access
- 28 May 2025
- Published by Wiley in Advanced Science
- Vol. 12 (31) , e01989
VOx‐Based Non‐Volatile Radio‐Frequency Switches for Reconfigurable Filter
Vanadium oxide (VOx) based memristor is a promising candidate for next‐generation non‐volatile memory and radio‐frequency (RF) switches due to its compatibility with wafer‐level integration and high‐frequency operation. This work demonstrates high‐performance VOx memristor with gold and silver electrodes, achieving a higher cutoff frequency compared to previously reported VOx devices. The devices exhibit long retention, high endurance (≈103 cycles), and nanosecond switching speeds, enabling the fabrication of RF switches with a cutoff frequency of ≈4.5 THz, low insertion loss (< 0.46 dB), and high isolation (>20 dB) from 0.1 to 20 GHz with stable operation extended to frequency up to 67 GHz. Leveraging these switches, a reconfigurable X‐band bandpass filter whose is realized center frequency is tuned from 8.2 GHz in the OFF state to 7.6 GHz in the ON state, achieving a tunable range of ≈600 MHz. This demonstration paves the way for compact and versatile RF front‐ends with improved frequency agility in advanced communication systems.
- 28 May 2025
- Published by Wiley in Advanced Science
- Vol. 12 (31) , e01989
Open AccessVOx‐Based Non‐Volatile Radio‐Frequency Switches for Reconfigurable Filter
Vanadium oxide (VOx) based memristor is a promising candidate for next‐generation non‐volatile memory and radio‐frequency (RF) switches due to its compatibility with wafer‐level integration and high‐frequency operation. This work demonstrates high‐performance VOx memristor with gold and silver electrodes, achieving a higher cutoff frequency compared to previously reported VOx devices. The devices exhibit long retention, high endurance (≈103 cycles), and nanosecond switching speeds, enabling the fabrication of RF switches with a cutoff frequency of ≈4.5 THz, low insertion loss (< 0.46 dB), and high isolation (>20 dB) from 0.1 to 20 GHz with stable operation extended to frequency up to 67 GHz. Leveraging these switches, a reconfigurable X‐band bandpass filter whose is realized center frequency is tuned from 8.2 GHz in the OFF state to 7.6 GHz in the ON state, achieving a tunable range of ≈600 MHz. This demonstration paves the way for compact and versatile RF front‐ends with improved frequency agility in advanced communication systems.