Andrés Giovanni González-Hernández
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Andrés Giovanni González-Hernández has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Ahmed Al-Ramthan
Faculty of Industrial and Manufacturing Technology and Engineering, Universiti Teknikal Malaysia Melaka, Hang Tuah Jaya, 76100 Durian Tunggal, Melaka, Malaysia
2 shared publications Juan Sebastián Martínez-Yáñez
2 shared publicationsJuan Sebastián Ramírez-Prieto
2 shared publicationsJ. C. Sarmiento-Triana
Universidad Industrial de Santander (UIS), Bucaramanga, Colombia
1 shared publicationM. H. Hernández-Rojas
Universidad Nacional de Colombia—Sede Manizales, Manizales, Colombia
1 shared publicationO. M. Moreno-Santos
Universidad Industrial de Santander (UIS), Bucaramanga, Colombia
1 shared publication
Latest Publications
- 7 October 2026
- Published by Springer Nature in Strength of Materials
- p. 1-13
Compressive strength of Al–7Si foams produced by 3D printing and investment casting
- 7 October 2026
- Published by Springer Nature in Strength of Materials
- p. 1-13
Compressive strength of Al–7Si foams produced by 3D printing and investment casting
- Open Access
- 1 January 2025
- Published by American Institute of Mathematical Sciences (AIMS) in AIMS Materials Science
- Vol. 12 (6) , 1153-1175
Comparative study of the mechanical properties of ASA, nylon, and nylon reinforced with carbon fiber components made by 3D printing
The mechanical performance of components fabricated via fused deposition modeling (FDM) is critically influenced by both processing parameters and material selection. In this work, a systematic comparison was performed among acrylonitrile styrene acrylate (ASA), polyamide (PA), and carbon fiber-reinforced polyamide (PA-CF) to assess their tensile and flexural responses at three infill densities (33%, 66%, and 100%). Standardized ASTM specimens were printed under controlled conditions, and mechanical testing was complemented with fracture surface inspection to identify failure mechanisms associated with layer adhesion and internal porosity. A statistical analysis based on an analysis of variance (ANOVA) design revealed that both material type and infill density exert significant effects on strength, stiffness, and strain at break, with a strong interaction between the two factors. Increasing infill density consistently enhanced tensile and flexural strengths, although the degree of improvement depended on the intrinsic ductility and interlayer bonding of each polymer. Among the tested materials, PA exhibited the highest tensile and flexural strengths combined with superior ductility, while ASA showed greater stiffness but lower elongation. The PA-CF composite displayed intermediate performance, possibly influenced by the short carbon fibers embedded in the filament, which create local discontinuities within the polymer matrix and reduce overall ductility. These findings provide valuable insights for optimizing FDM parameters to enhance the structural integrity of additively manufactured components.
- 1 January 2025
- Published by American Institute of Mathematical Sciences (AIMS) in AIMS Materials Science
- Vol. 12 (6) , 1153-1175
Open AccessComparative study of the mechanical properties of ASA, nylon, and nylon reinforced with carbon fiber components made by 3D printing
The mechanical performance of components fabricated via fused deposition modeling (FDM) is critically influenced by both processing parameters and material selection. In this work, a systematic comparison was performed among acrylonitrile styrene acrylate (ASA), polyamide (PA), and carbon fiber-reinforced polyamide (PA-CF) to assess their tensile and flexural responses at three infill densities (33%, 66%, and 100%). Standardized ASTM specimens were printed under controlled conditions, and mechanical testing was complemented with fracture surface inspection to identify failure mechanisms associated with layer adhesion and internal porosity. A statistical analysis based on an analysis of variance (ANOVA) design revealed that both material type and infill density exert significant effects on strength, stiffness, and strain at break, with a strong interaction between the two factors. Increasing infill density consistently enhanced tensile and flexural strengths, although the degree of improvement depended on the intrinsic ductility and interlayer bonding of each polymer. Among the tested materials, PA exhibited the highest tensile and flexural strengths combined with superior ductility, while ASA showed greater stiffness but lower elongation. The PA-CF composite displayed intermediate performance, possibly influenced by the short carbon fibers embedded in the filament, which create local discontinuities within the polymer matrix and reduce overall ductility. These findings provide valuable insights for optimizing FDM parameters to enhance the structural integrity of additively manufactured components.
- Open Access
- 1 January 2025
- Published by American Institute of Mathematical Sciences (AIMS) in AIMS Materials Science
- Vol. 12 (2) , 363-379
Effect of raster angle on the tensile and flexural strength of 3D printed PLA+ parts
In fused deposition modeling (FDM) 3D printing, the properties and performance of the fabricated components are profoundly affected by the selected process parameters. Therefore, it is crucial to choose and optimize these parameters to improve the quality and mechanical characteristics of the final product. Given this, the present study explored the mechanical properties of 3D-printed components fabricated from polylactic acid (PLA)+ filament, specifically examining how different raster angles influence their flexural and tensile performance. Three raster angle conditions were investigated: parallel (0°/0°), grid (0°/90°), and crisscross (45°/−45°). The results demonstrate that the raster angle has a significant effect on the flexural and tensile strength of the printed specimens. The parallel raster (0°/0°) produced the highest flexural strength, attributed to the alignment of the fibers perpendicular to the applied load, which enhances the load capacity. Conversely, the crisscross (45°/−45°) orientation resulted in the lowest flexural strength but exhibited greater ductility, as evidenced by extensive plastic deformation. This increased ductility is attributed to the material's ability to absorb more energy before failure, resulting from favorable shear deformation dynamics. In tensile testing, the parallel raster (0°/0°) showed superior strength, while the grid and crisscross orientations followed with progressively lower values. The fracture behavior revealed that samples 3D printed with a 45°/−45° raster angle tend to fail along the raster orientation, primarily due to the development of shear stresses.
- 1 January 2025
- Published by American Institute of Mathematical Sciences (AIMS) in AIMS Materials Science
- Vol. 12 (2) , 363-379
Open AccessEffect of raster angle on the tensile and flexural strength of 3D printed PLA+ parts
In fused deposition modeling (FDM) 3D printing, the properties and performance of the fabricated components are profoundly affected by the selected process parameters. Therefore, it is crucial to choose and optimize these parameters to improve the quality and mechanical characteristics of the final product. Given this, the present study explored the mechanical properties of 3D-printed components fabricated from polylactic acid (PLA)+ filament, specifically examining how different raster angles influence their flexural and tensile performance. Three raster angle conditions were investigated: parallel (0°/0°), grid (0°/90°), and crisscross (45°/−45°). The results demonstrate that the raster angle has a significant effect on the flexural and tensile strength of the printed specimens. The parallel raster (0°/0°) produced the highest flexural strength, attributed to the alignment of the fibers perpendicular to the applied load, which enhances the load capacity. Conversely, the crisscross (45°/−45°) orientation resulted in the lowest flexural strength but exhibited greater ductility, as evidenced by extensive plastic deformation. This increased ductility is attributed to the material's ability to absorb more energy before failure, resulting from favorable shear deformation dynamics. In tensile testing, the parallel raster (0°/0°) showed superior strength, while the grid and crisscross orientations followed with progressively lower values. The fracture behavior revealed that samples 3D printed with a 45°/−45° raster angle tend to fail along the raster orientation, primarily due to the development of shear stresses.