Usmonjon F. Berdiyev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Usmonjon F. Berdiyev has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Ilyos Kh. Khudaykulov
Institute of Ion-Plasma and Laser Technologies named after U.A. Arifov, Academy of Sciences of the Republic of Uzbekistan, Tashkent, Uzbekistan
3 shared publications - Shukhrat Ch. Iskandarov3 shared publications
- Khatam B. Ashurov
Institute of Ion-Plasma and Laser Technologies named after U.A. Arifov, Academy of Sciences of the Republic of Uzbekistan, Tashkent, Uzbekistan
2 shared publications - Temur K. Turdaliev
Arifov Institute of Ion-Plasma and Laser Technologies Uzbekistan Academy of Sciences 100125 Durmon Yuli st. 33 Tashkent Uzbekistan
2 shared publications A.J. Amirova
1 shared publicationBoburjon R. Kakhramonov
1 shared publication
Latest Publications
- Open Access
- 10 June 2026
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 2,p. 156-161
The Systematic Correlation Between Synthesis Parameters and the Particle Size of Nickel Oxide Nanocatalysts Prepared by the Sol–Gel Method
In this work, the sol-gel synthesis of nickel oxide (NiO) nanoparticles was systematically examined with respect to key parameters, including precursor type, reagent molar ratio, reaction time, and calcination temperature. A comparative evaluation of different nickel-based salts identified nickel nitrate as the most suitable precursor. Structural–phase characterization by X-ray diffraction (XRD) demonstrated that the nanoparticles synthesized at varying reagent ratios possessed well-defined crystalline phases, with an average crystallite size of ~11 nm. Prolonged reaction times were observed to promote agglomeration processes. Raman spectroscopic analysis revealed the presence of phonon and magnon vibrational modes, which were strongly dependent on particle size and calcination conditions. Transmission electron microscopy (TEM) confirmed a particle size distribution in the range of 3÷19 nm. Collectively, these results establish the synthesis–structure relationship and provide a framework for defining optimal conditions for preparing NiO nanocatalysts.
- 10 June 2026
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 2,p. 156-161
Open AccessThe Systematic Correlation Between Synthesis Parameters and the Particle Size of Nickel Oxide Nanocatalysts Prepared by the Sol–Gel Method
In this work, the sol-gel synthesis of nickel oxide (NiO) nanoparticles was systematically examined with respect to key parameters, including precursor type, reagent molar ratio, reaction time, and calcination temperature. A comparative evaluation of different nickel-based salts identified nickel nitrate as the most suitable precursor. Structural–phase characterization by X-ray diffraction (XRD) demonstrated that the nanoparticles synthesized at varying reagent ratios possessed well-defined crystalline phases, with an average crystallite size of ~11 nm. Prolonged reaction times were observed to promote agglomeration processes. Raman spectroscopic analysis revealed the presence of phonon and magnon vibrational modes, which were strongly dependent on particle size and calcination conditions. Transmission electron microscopy (TEM) confirmed a particle size distribution in the range of 3÷19 nm. Collectively, these results establish the synthesis–structure relationship and provide a framework for defining optimal conditions for preparing NiO nanocatalysts.
- Open Access
- 8 December 2025
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 4,p. 449-453
Effect of Substrate Temperature on the Morphology and Crystallinity of TiO₂ Thin Films Grown by ALD Using TTIP and H₂O
This study investigates the influence of substrate temperature on the morphological and structural characteristics of TiO2 thin films synthesized by thermal ALD using titanium tetraisopropoxide and water as precursors. The substrate temperature was varied from 200 to 275 °C in 25 °C increments. Surface morphology was examined using atomic force microscopy, while the crystalline structure was analyzed by XRD and Raman spectroscopy. It was found that films deposited at 200 °C exhibited an amorphous structure and a smooth, conformal surface with minimal roughness. Increasing the temperature to 225 °C led to the formation of microstructures and the emergence of initial signs of crystallization, accompanied by an increase in surface roughness. At 250-275 °C, a well-defined polycrystalline anatase structure was formed, characterized by grain development and nanostructure agglomeration, as evidenced by the increased intensity of diffraction peaks and higher surface roughness parameters. According to the XRD analysis, the average crystallite size ranged from 32 to 71 nm, depending on the synthesis temperature. The results demonstrate that deposition temperature exerts a comprehensive effect on both the phase composition and surface morphology of TiO2 films, which must be considered for their application in functional nanostructures, photocatalytic systems, sensors, and microelectronic devices.
- 8 December 2025
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 4,p. 449-453
Open AccessEffect of Substrate Temperature on the Morphology and Crystallinity of TiO₂ Thin Films Grown by ALD Using TTIP and H₂O
This study investigates the influence of substrate temperature on the morphological and structural characteristics of TiO2 thin films synthesized by thermal ALD using titanium tetraisopropoxide and water as precursors. The substrate temperature was varied from 200 to 275 °C in 25 °C increments. Surface morphology was examined using atomic force microscopy, while the crystalline structure was analyzed by XRD and Raman spectroscopy. It was found that films deposited at 200 °C exhibited an amorphous structure and a smooth, conformal surface with minimal roughness. Increasing the temperature to 225 °C led to the formation of microstructures and the emergence of initial signs of crystallization, accompanied by an increase in surface roughness. At 250-275 °C, a well-defined polycrystalline anatase structure was formed, characterized by grain development and nanostructure agglomeration, as evidenced by the increased intensity of diffraction peaks and higher surface roughness parameters. According to the XRD analysis, the average crystallite size ranged from 32 to 71 nm, depending on the synthesis temperature. The results demonstrate that deposition temperature exerts a comprehensive effect on both the phase composition and surface morphology of TiO2 films, which must be considered for their application in functional nanostructures, photocatalytic systems, sensors, and microelectronic devices.
- Open Access
- 8 December 2025
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 4,p. 601-606
Effect of TiO₂ Layer Thickness on Electrode Degradation in Redox Flow Batteries
In this work, TiO2 coatings of various thicknesses were deposited on carbon felt fibers using the ALD (Atomic Layer Deposition) method, and the mechanical and electrochemical properties of the electrodes were studied. The experimental results show that the TiO2 coating effectively protects and enhances the stability of carbon wet electrodes. While a mass loss of 4% was observed in the untreated cathode electrode, this figure decreased to 1.6-1.7% when a TiO2 coating was applied. When the coating thickness was increased from 50 nm to 300 nm, no significant change in mass loss was observed, which indicates that even thin coatings provide effective protection. The mass loss in the anode electrode was relatively small, ranging from 2% in the untreated state and 0.5-1.1% in the coated states. This is explained by the lower anode potential than the cathode and the low sensitivity of the V2+/V3+ redox reaction at the anode. It was found that the titanium dioxide coating plays an important role in increasing the electrochemical degradation and corrosion resistance of the electrodes, as well as in extending the battery life. It was also shown that a 50 nm thick TiO2 coating can provide effective protection, while very thick coatings can limit electron mobility. These results confirm that TiO2 coatings are one of the promising solutions for protecting electrode materials in vanadium flow batteries.
- 8 December 2025
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 4,p. 601-606
Open AccessEffect of TiO₂ Layer Thickness on Electrode Degradation in Redox Flow Batteries
In this work, TiO2 coatings of various thicknesses were deposited on carbon felt fibers using the ALD (Atomic Layer Deposition) method, and the mechanical and electrochemical properties of the electrodes were studied. The experimental results show that the TiO2 coating effectively protects and enhances the stability of carbon wet electrodes. While a mass loss of 4% was observed in the untreated cathode electrode, this figure decreased to 1.6-1.7% when a TiO2 coating was applied. When the coating thickness was increased from 50 nm to 300 nm, no significant change in mass loss was observed, which indicates that even thin coatings provide effective protection. The mass loss in the anode electrode was relatively small, ranging from 2% in the untreated state and 0.5-1.1% in the coated states. This is explained by the lower anode potential than the cathode and the low sensitivity of the V2+/V3+ redox reaction at the anode. It was found that the titanium dioxide coating plays an important role in increasing the electrochemical degradation and corrosion resistance of the electrodes, as well as in extending the battery life. It was also shown that a 50 nm thick TiO2 coating can provide effective protection, while very thick coatings can limit electron mobility. These results confirm that TiO2 coatings are one of the promising solutions for protecting electrode materials in vanadium flow batteries.
- Open Access
- 3 March 2025
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 1,p. 265-271
Influence of SiO2 Nanoparticles on the Characteristics of a Polyvinyl Alcohol-Based Proton Exchange Composite Membrane
This paper presents a study of nanocomposite membranes based on cross-linked polyvinyl alcohol with silica nanoparticles, fabricated by solution casting, for application in vanadium redox batteries (VRFBs). The structure of the membranes was studied by Fourier transform infrared spectroscopy (FT-IR). It was found that the nanoparticles were successfully integrated into the matrix of the proton exchange membrane to improve its performance. The synthesis of silica nanoparticles by in situ sol-gel method in polymer solution showed better performance compared to the addition of prepared nanoparticles. The membrane properties such as mechanical properties, water absorption, ion exchange material (IEM), proton conductivity and permeability to vanadium ions were investigated. The nanocomposite membranes showed higher water absorption, IEM and lower permeability for vanadium ions compared to Nafion117 membrane. The test results of single cell VRFB with nanocomposite membranes showed higher Coulomb yield (CE) and efficiency (EE) up to 81.51% compared to Nafion117. The self-discharge rate of VRFBs with nanocomposite membranes was lower than that of Nafion117. After 50 test cycles, the nanocomposite membrane showed stable battery performance. The results indicate that nanocomposite membranes are a promising and affordable alternative material for Nafion117 in VRFBs.
- 3 March 2025
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 1,p. 265-271
Open AccessInfluence of SiO2 Nanoparticles on the Characteristics of a Polyvinyl Alcohol-Based Proton Exchange Composite Membrane
This paper presents a study of nanocomposite membranes based on cross-linked polyvinyl alcohol with silica nanoparticles, fabricated by solution casting, for application in vanadium redox batteries (VRFBs). The structure of the membranes was studied by Fourier transform infrared spectroscopy (FT-IR). It was found that the nanoparticles were successfully integrated into the matrix of the proton exchange membrane to improve its performance. The synthesis of silica nanoparticles by in situ sol-gel method in polymer solution showed better performance compared to the addition of prepared nanoparticles. The membrane properties such as mechanical properties, water absorption, ion exchange material (IEM), proton conductivity and permeability to vanadium ions were investigated. The nanocomposite membranes showed higher water absorption, IEM and lower permeability for vanadium ions compared to Nafion117 membrane. The test results of single cell VRFB with nanocomposite membranes showed higher Coulomb yield (CE) and efficiency (EE) up to 81.51% compared to Nafion117. The self-discharge rate of VRFBs with nanocomposite membranes was lower than that of Nafion117. After 50 test cycles, the nanocomposite membrane showed stable battery performance. The results indicate that nanocomposite membranes are a promising and affordable alternative material for Nafion117 in VRFBs.