Edgar Williams Villanueva Martinez
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Edgar Williams Villanueva Martinez has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Jorge Montaño-Pisfil
Faculty of Electrical and Electronic Engineering, Universidad Nacional del Callao, Callao 07011, Peru
3 shared publications - Juan Taumaturgo Medina-Collana
Faculty of Chemical Engineering, Centro de Investigación para la Educación, National University of Callao, Juan Pablo II 306 Avenue, Callao 07011, Peru
3 shared publications - Fredy Andrés Taipe Castro
Centro de Investigación de Ingeniería de Procesos de Tratamiento de Aguas, Facultad de Ingeniería Química, Universidad Nacional del Callao, Bellavista, Callao 07011, Peru
2 shared publications - Kevin Remigio Azorza Gillen
Centro de Investigación de Ingeniería de Procesos de Tratamiento de Aguas, Facultad de Ingeniería Química, Universidad Nacional del Callao, Bellavista, Callao 07011, Peru
2 shared publications - Lopez Herrera
Centro de Investigación de Ingeniería de Procesos de Tratamiento de Aguas, Facultad de Ingeniería Química, Universidad Nacional del Callao, Bellavista 07011, Peru
2 shared publications - Luis Américo Carrasco-Venegas
Centro de Investigación en Bioenergía, Universidad Nacional del Callao, Callao 15001, Peru
2 shared publications
Latest Publications
- Open Access
- 3 June 2026
- Published by MDPI AG in Sustainability
- Vol. 18 (11) , 5647
Forward Osmosis for Sustainable Brackish Water Desalination
The desalination of brackish and seawater has emerged as a critical strategy to address growing water scarcity in regions experiencing water stress, particularly within the context of sustainable water resource management. Among available technologies, forward osmosis (FO) has gained increasing attention due to its potential for lower energy consumption and reduced environmental impact compared to conventional desalination processes. In this study, commercial HFFO2 (Aquaporin Inside) membrane from FO was used. A complete factorial design with three factors was used: feed solution concentration (1.5 and 3 g/L NaCl), draw solution concentration (15, 25, and 35 g/L NaCl), and feed solution flow rate (600 and 1000 mL/min) on the percentage of recovery and water flux. Tests showed that as the feed concentration decreases from 3 to 1.5 g/L of NaCl, water recovery improves by 23.6%. The results revealed that increasing the concentration of the draw solution from 15 to 25 g/L of NaCl increased water recovery by 22.2%. However, for a concentration variation of 25 to 35 g/L, this increase is insignificant at 0.92%. The results showed that, with a concentration of 1.5 g/L of NaCl, a feed flow rate of 1000 mL/min, and a concentration of 25 g/L of NaCl as the draw solution, a higher water recovery rate (95.4839%) was achieved. Similarly, average water flux values of 2.18, 2.43, and 2.68 were observed when using draw solutions of 15, 25, and 35 g/L of NaCl, respectively. In addition, increasing the FS flow rate slightly reduces water recovery (from 76.04% to 74.06%). Consequently, the forward osmosis process has proven to be effective, practical, viable, and environmentally friendly for water desalination, as well as being applicable to the treatment of wastewater with high electrical conductivity.- 3 June 2026
- Published by MDPI AG in Sustainability
- Vol. 18 (11) , 5647
Open AccessForward Osmosis for Sustainable Brackish Water Desalination
The desalination of brackish and seawater has emerged as a critical strategy to address growing water scarcity in regions experiencing water stress, particularly within the context of sustainable water resource management. Among available technologies, forward osmosis (FO) has gained increasing attention due to its potential for lower energy consumption and reduced environmental impact compared to conventional desalination processes. In this study, commercial HFFO2 (Aquaporin Inside) membrane from FO was used. A complete factorial design with three factors was used: feed solution concentration (1.5 and 3 g/L NaCl), draw solution concentration (15, 25, and 35 g/L NaCl), and feed solution flow rate (600 and 1000 mL/min) on the percentage of recovery and water flux. Tests showed that as the feed concentration decreases from 3 to 1.5 g/L of NaCl, water recovery improves by 23.6%. The results revealed that increasing the concentration of the draw solution from 15 to 25 g/L of NaCl increased water recovery by 22.2%. However, for a concentration variation of 25 to 35 g/L, this increase is insignificant at 0.92%. The results showed that, with a concentration of 1.5 g/L of NaCl, a feed flow rate of 1000 mL/min, and a concentration of 25 g/L of NaCl as the draw solution, a higher water recovery rate (95.4839%) was achieved. Similarly, average water flux values of 2.18, 2.43, and 2.68 were observed when using draw solutions of 15, 25, and 35 g/L of NaCl, respectively. In addition, increasing the FS flow rate slightly reduces water recovery (from 76.04% to 74.06%). Consequently, the forward osmosis process has proven to be effective, practical, viable, and environmentally friendly for water desalination, as well as being applicable to the treatment of wastewater with high electrical conductivity. - Open Access
Obtaining Biodiesel from Soybean Vegetable Oil Using a Hydrodynamic Cavitation Reactor
Hydrodynamic cavitation (HC) is an efficient technique for biodiesel production. The main contribution of this study is the development of a modular reactor with a universal stainless steel joint, whose design facilitates the installation, replacement, and maintenance of the orifice plate by eliminating flanges and bolts during assembly. Using this reactor, the study evaluated the synergistic interaction between feed pressure and methanol:oil molar ratio in the transesterification of soybean oil, employing a 32 factorial design. The orifice plate was 3 mm thick and had 19 holes with a diameter of 1.0 mm, installed downstream of the pump. The process was carried out for 45 min, using NaOH at 1 wt% relative to the oil and at 60 ± 5 °C. Feed pressures of 1.72, 2.41, and 3.10 bar and methanol:oil molar ratios of 6:1, 8:1, and 10:1 were evaluated, reaching a maximum yield of 92.98% at 3.10 bar and 8:1. Analysis of variance (ANOVA) confirmed a significant interaction (p < 0.0001) and allowed a second-order polynomial model to be fitted (R2 = 0.9981). In contrast, conventional mechanical agitation required 90 min to achieve 95% yield. The biodiesel produced met most American Society for Testing and Materials (ASTM) D6751 requirements, confirming the potential of HC as a viable alternative for intensifying biodiesel production.
Open AccessObtaining Biodiesel from Soybean Vegetable Oil Using a Hydrodynamic Cavitation Reactor
Hydrodynamic cavitation (HC) is an efficient technique for biodiesel production. The main contribution of this study is the development of a modular reactor with a universal stainless steel joint, whose design facilitates the installation, replacement, and maintenance of the orifice plate by eliminating flanges and bolts during assembly. Using this reactor, the study evaluated the synergistic interaction between feed pressure and methanol:oil molar ratio in the transesterification of soybean oil, employing a 32 factorial design. The orifice plate was 3 mm thick and had 19 holes with a diameter of 1.0 mm, installed downstream of the pump. The process was carried out for 45 min, using NaOH at 1 wt% relative to the oil and at 60 ± 5 °C. Feed pressures of 1.72, 2.41, and 3.10 bar and methanol:oil molar ratios of 6:1, 8:1, and 10:1 were evaluated, reaching a maximum yield of 92.98% at 3.10 bar and 8:1. Analysis of variance (ANOVA) confirmed a significant interaction (p < 0.0001) and allowed a second-order polynomial model to be fitted (R2 = 0.9981). In contrast, conventional mechanical agitation required 90 min to achieve 95% yield. The biodiesel produced met most American Society for Testing and Materials (ASTM) D6751 requirements, confirming the potential of HC as a viable alternative for intensifying biodiesel production.
- Open Access
- 13 June 2025
- Published by MDPI AG in Sustainability
- Vol. 17 (12) , 5465
Electrochemical Production of Hypochlorous Acid and Sodium Hydroxide Using Ion Exchange Membranes
Given the problems related to drinking water supplies in rural and economically disadvantaged regions, point-of-use disinfection technologies are a viable alternative to improve access to drinking. Electrochlorinators are devices that produce chlorine-based disinfectants onsite via the electrolysis of a sodium chloride solution. In this research, we have constructed an innovative laboratory-scale three-compartment cell that includes two ion exchange membranes, fixed between two electrodes; in the anodic compartment, an acidic mixture of chlorine-based species (Cl2, HClO, HCl and ClO−) is obtained, and, in the cathodic compartment, an alkaline solution is present (NaOH and hydrogen gas), while the central compartment is fed with a sodium chloride solution. The Taguchi methodology was used to examine the impact of the process operating conditions on the results obtained. The effects of the electrical potential levels (4.5, 6 and 7 V), electrolysis times (30, 60 and 90 min) and initial sodium chloride concentrations (5, 15 and 30 g/L) on the physical and chemical characteristics (concentrations of available chlorine and sodium hydroxide and pH of the solutions) and energy consumption were investigated. Variations in the electrical potential significantly influenced the concentration levels of active chlorine and sodium hydroxide produced, as well as the pH values of the respective solutions. The most favorable conditions for the production of electrolyzed water were an electrical potential of 7 volts, an electrolysis time of 90 min and a concentration of 30 g/L of sodium chloride, which was verified by ANOVA. The maximum concentration of active chlorine reached 290 mg/L and that of sodium hydroxide reached 1450 mg/L without the presence of hypochlorite ions under the best synthesis conditions. The energy consumption was 18.6 kWh/kg Cl2 and 4.4 kWh/kg NaOH, while the average electric current efficiency for sodium hydroxide formation reached 88.9%. Similarly, the maximum conversion of chloride ions reached 24.37% under the best operating conditions.
- 13 June 2025
- Published by MDPI AG in Sustainability
- Vol. 17 (12) , 5465
Open AccessElectrochemical Production of Hypochlorous Acid and Sodium Hydroxide Using Ion Exchange Membranes
Given the problems related to drinking water supplies in rural and economically disadvantaged regions, point-of-use disinfection technologies are a viable alternative to improve access to drinking. Electrochlorinators are devices that produce chlorine-based disinfectants onsite via the electrolysis of a sodium chloride solution. In this research, we have constructed an innovative laboratory-scale three-compartment cell that includes two ion exchange membranes, fixed between two electrodes; in the anodic compartment, an acidic mixture of chlorine-based species (Cl2, HClO, HCl and ClO−) is obtained, and, in the cathodic compartment, an alkaline solution is present (NaOH and hydrogen gas), while the central compartment is fed with a sodium chloride solution. The Taguchi methodology was used to examine the impact of the process operating conditions on the results obtained. The effects of the electrical potential levels (4.5, 6 and 7 V), electrolysis times (30, 60 and 90 min) and initial sodium chloride concentrations (5, 15 and 30 g/L) on the physical and chemical characteristics (concentrations of available chlorine and sodium hydroxide and pH of the solutions) and energy consumption were investigated. Variations in the electrical potential significantly influenced the concentration levels of active chlorine and sodium hydroxide produced, as well as the pH values of the respective solutions. The most favorable conditions for the production of electrolyzed water were an electrical potential of 7 volts, an electrolysis time of 90 min and a concentration of 30 g/L of sodium chloride, which was verified by ANOVA. The maximum concentration of active chlorine reached 290 mg/L and that of sodium hydroxide reached 1450 mg/L without the presence of hypochlorite ions under the best synthesis conditions. The energy consumption was 18.6 kWh/kg Cl2 and 4.4 kWh/kg NaOH, while the average electric current efficiency for sodium hydroxide formation reached 88.9%. Similarly, the maximum conversion of chloride ions reached 24.37% under the best operating conditions.