Alžběta Měrková
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Alžběta Měrková has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Petr Hála
Czech Technical University in Prague
3 shared publications - Přemysl Kheml
Experimental Centre, Faculty of Civil Engineering, Czech Technical University in Prague, Thákurova 7, 166 29 Prague, Czech Republic
2 shared publications Alexandre Perrot
SYNPO Pardubice, Czech Republic
1 shared publication- Alexandre Perrot
SYNPO, akciová společnost, S. K. Neumanna 1316, 532 07 Pardubice, Czech Republic
1 shared publication Bachir Belkassem
Royal Military Academy
1 shared publicationDavid Lecompte
Royal Military Academy
1 shared publication
Latest Publications
- Open Access
- 13 November 2026
- Published by SAGE Publications in International Journal of Protective Structures
Experimental and numerical investigation of blast-wave propagation in a two-room structure: Effects of confinement, opening geometry, and breakable media
Blast-wave propagation within interconnected compartments is strongly influenced by the characteristics of openings connecting adjacent spaces. While previous studies have investigated the effects of compartment geometry and opening configuration in the two-room problem, limited attention has been given to the influence of breakable media on blast-wave transmission and their representation in numerical simulations. This study presents a combined experimental and numerical investigation of blast-wave propagation in a two-compartment structure, focusing on the effects of receiving-compartment confinement, partition configuration, and a breakable medium located within the opening connecting the compartments. A series of small-scale blast experiments was conducted using a two-compartment model instrumented with pressure sensors. Several candidate materials were evaluated as representative breakable media, leading to the selection of a 75 g/m 2 paper sheet. High-speed Digital Image Correlation was employed to determine a failure criterion for numerical implementation. A computational fluid dynamics model, incorporating the breakable medium modelled as glazing based on a pressure-impulse curve, was subsequently developed in ProSAir and validated against the experimental measurements. The results demonstrate that confinement significantly increases blast loading within the receiving compartment. The introduction of a breakable medium resulted in delays in blast-wave arrival and reductions in the first pressure peak and the positive-phase impulse. The numerical model successfully validated the experimentally observed trends. The study improves the understanding of blast-wave transmission in interconnected compartments and presents a validated methodology for modelling blast-wave interaction with breakable media in numerical simulations.
- 13 November 2026
- Published by SAGE Publications in International Journal of Protective Structures
Open AccessExperimental and numerical investigation of blast-wave propagation in a two-room structure: Effects of confinement, opening geometry, and breakable media
Blast-wave propagation within interconnected compartments is strongly influenced by the characteristics of openings connecting adjacent spaces. While previous studies have investigated the effects of compartment geometry and opening configuration in the two-room problem, limited attention has been given to the influence of breakable media on blast-wave transmission and their representation in numerical simulations. This study presents a combined experimental and numerical investigation of blast-wave propagation in a two-compartment structure, focusing on the effects of receiving-compartment confinement, partition configuration, and a breakable medium located within the opening connecting the compartments. A series of small-scale blast experiments was conducted using a two-compartment model instrumented with pressure sensors. Several candidate materials were evaluated as representative breakable media, leading to the selection of a 75 g/m 2 paper sheet. High-speed Digital Image Correlation was employed to determine a failure criterion for numerical implementation. A computational fluid dynamics model, incorporating the breakable medium modelled as glazing based on a pressure-impulse curve, was subsequently developed in ProSAir and validated against the experimental measurements. The results demonstrate that confinement significantly increases blast loading within the receiving compartment. The introduction of a breakable medium resulted in delays in blast-wave arrival and reductions in the first pressure peak and the positive-phase impulse. The numerical model successfully validated the experimentally observed trends. The study improves the understanding of blast-wave transmission in interconnected compartments and presents a validated methodology for modelling blast-wave interaction with breakable media in numerical simulations.
- 25 September 2025
- Published by SAGE Publications in International Journal of Protective Structures
Resistance of high-performance concrete structural members with dispersed fibre reinforcement, E-glass/epoxy layer and polyurethane coating to direct contact blast
This study investigates the enhancement of blast resistance in high-performance fibre-reinforced concrete (HPFRC) panels by incorporating them into layered composite structures. Recently, a modular system for blast and ballistic protection was introduced, featuring thin HPFRC panels. Although HPFRC demonstrates increased resistance to dynamic loads, it remains vulnerable to scabbing under extreme blast pressures. To further optimize the blast resilience of the protective modular system, a three-layered sandwich structure composed of HPFRC, polyurethane, and E-glass/epoxy was developed. The study evaluated the impact of additional layers and their configurations by subjecting different panel arrangements to direct contact blasts. These configurations included two-layer systems (HPFRC and E-glass/epoxy) and three-layer systems with an HPFRC core, a polyurethane layer, and an E-glass/epoxy layer. Key factors analysed included crater formation, scabbing, reaction forces, and residual flexural strength. Comparisons with the existing protective modular system, currently employing bare HPFRC panels, offered insights into the distinct blast responses of each structure, providing guidance for structural optimization to enhance blast resistance.
- 25 September 2025
- Published by SAGE Publications in International Journal of Protective Structures
Resistance of high-performance concrete structural members with dispersed fibre reinforcement, E-glass/epoxy layer and polyurethane coating to direct contact blast
This study investigates the enhancement of blast resistance in high-performance fibre-reinforced concrete (HPFRC) panels by incorporating them into layered composite structures. Recently, a modular system for blast and ballistic protection was introduced, featuring thin HPFRC panels. Although HPFRC demonstrates increased resistance to dynamic loads, it remains vulnerable to scabbing under extreme blast pressures. To further optimize the blast resilience of the protective modular system, a three-layered sandwich structure composed of HPFRC, polyurethane, and E-glass/epoxy was developed. The study evaluated the impact of additional layers and their configurations by subjecting different panel arrangements to direct contact blasts. These configurations included two-layer systems (HPFRC and E-glass/epoxy) and three-layer systems with an HPFRC core, a polyurethane layer, and an E-glass/epoxy layer. Key factors analysed included crater formation, scabbing, reaction forces, and residual flexural strength. Comparisons with the existing protective modular system, currently employing bare HPFRC panels, offered insights into the distinct blast responses of each structure, providing guidance for structural optimization to enhance blast resistance.
- Open Access
- 7 May 2025
- Published by Czech Technical University in Prague - Central Library in Acta Polytechnica
- Vol. 65 (2) , 188-197
Experimental investigation of polyurethane-coated HPFRC panels under direct contact blast
High-performance fibre-reinforced concrete (HPFRC) exhibits exceptional resistance to dynamic loading, making it a promising material for structures exposed to blast or impact events. However, when used to produce thin panels, it can experience scabbing under extreme loads. To address this and enhance the blast resistance, this study explores the application of a polyurethane (PU) coating to the HPFRC panels. Coated and uncoated panels undergo direct contact blast testing and various factors, such as crater area, rear fragment formation, cracking, and residual flexural strength, are analysed. Our study indicates that applying a PU coating to the panels could effectively prevent scabbing and mitigate the risk of complete perforation, while it appears that it results in the panel absorbing more energy during blast, leading to increased damage and a subsequent decrease in residual flexural strength compared to bare panels.
- 7 May 2025
- Published by Czech Technical University in Prague - Central Library in Acta Polytechnica
- Vol. 65 (2) , 188-197
Open AccessExperimental investigation of polyurethane-coated HPFRC panels under direct contact blast
High-performance fibre-reinforced concrete (HPFRC) exhibits exceptional resistance to dynamic loading, making it a promising material for structures exposed to blast or impact events. However, when used to produce thin panels, it can experience scabbing under extreme loads. To address this and enhance the blast resistance, this study explores the application of a polyurethane (PU) coating to the HPFRC panels. Coated and uncoated panels undergo direct contact blast testing and various factors, such as crater area, rear fragment formation, cracking, and residual flexural strength, are analysed. Our study indicates that applying a PU coating to the panels could effectively prevent scabbing and mitigate the risk of complete perforation, while it appears that it results in the panel absorbing more energy during blast, leading to increased damage and a subsequent decrease in residual flexural strength compared to bare panels.