Xi Yao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Xi Yao has a total of 57 co-authors. Here are the top co-authors by number of shared publications:
- Hong Wang
Department of Materials Science and Engineering Southern University of Science and Technology Shenzhen China
4 shared publications Liangying Zhang
Functional Materials Research Laboratory , Tongji University , Shanghai, 200092, China
4 shared publications- Xusheng Wang
Key Laboratory of Advanced Civil Engineering Materials of the Ministry of Education, Functional Materials Research Laboratory, School of Materials Science and Engineering, Tongji University, Shanghai, China
4 shared publications - Chun Lung Philip Chen
South China University of Technology
2 shared publications - Di Zhou
Xi’an Jiaotong University
2 shared publications - Fagui Liu
School of Computer Science and Engineering, South China University of Technology, Guangzhou, China
2 shared publications
Latest Publications
- 9 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (6) , 9300-9316
FBLSC: Fuzzy BLS-Based Competitive Clustering Optimization Algorithm for Energy Efficient in Wireless Sensor Networks
Improving energy efficiency in wireless sensor networks (WSNs) is critical to ensuring effective transmission and prolonging network lifetime. However, most existing clustering methods are designed for relatively static scenarios and thus fail to cope with dynamic scenarios such as node mobility, topology variations, and uneven energy consumption, leading to poor adaptability, suboptimal real-time performance, and low energy efficiency, and significantly hinder the applicability in real-world WSNs. To address these challenges, we propose a structural lightweight fuzzy broad learning-based competitive clustering algorithm (FBLSC) for efficient cluster head (CH) selection and adaptive clustering in dynamic WSNs. Specifically, a fuzzy logic system (FLS) is employed to extract and evaluate node features under uncertainty, generating compete value (CV), which are then used to train a broad learning system (BLS) for fast and accurate CH prediction. Compared with traditional fuzzy systems and PSO-based models, the proposed hybrid structure improves adaptability, learning speed, and decision accuracy while maintaining low computational complexity. The experimental results show that, averaged over six representative network scenarios, FBLSC reduces average energy consumption by 61.8%, achieves +107.2% longer LND network lifetime, and improves throughput by 97.7% compared with the same baseline. Due to its ability to enhance energy efficiency and prolong network lifetime, FBLSC is well-suited for deployment in dynamic, energy-constrained application scenarios such as environmental monitoring, smart agriculture, emergency response systems, and others.
- 9 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (6) , 9300-9316
FBLSC: Fuzzy BLS-Based Competitive Clustering Optimization Algorithm for Energy Efficient in Wireless Sensor Networks
Improving energy efficiency in wireless sensor networks (WSNs) is critical to ensuring effective transmission and prolonging network lifetime. However, most existing clustering methods are designed for relatively static scenarios and thus fail to cope with dynamic scenarios such as node mobility, topology variations, and uneven energy consumption, leading to poor adaptability, suboptimal real-time performance, and low energy efficiency, and significantly hinder the applicability in real-world WSNs. To address these challenges, we propose a structural lightweight fuzzy broad learning-based competitive clustering algorithm (FBLSC) for efficient cluster head (CH) selection and adaptive clustering in dynamic WSNs. Specifically, a fuzzy logic system (FLS) is employed to extract and evaluate node features under uncertainty, generating compete value (CV), which are then used to train a broad learning system (BLS) for fast and accurate CH prediction. Compared with traditional fuzzy systems and PSO-based models, the proposed hybrid structure improves adaptability, learning speed, and decision accuracy while maintaining low computational complexity. The experimental results show that, averaged over six representative network scenarios, FBLSC reduces average energy consumption by 61.8%, achieves +107.2% longer LND network lifetime, and improves throughput by 97.7% compared with the same baseline. Due to its ability to enhance energy efficiency and prolong network lifetime, FBLSC is well-suited for deployment in dynamic, energy-constrained application scenarios such as environmental monitoring, smart agriculture, emergency response systems, and others.
- 9 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Network and Service Management
- Vol. 22 (5) , 5015-5030
Category-Constrained Broad Recurrent System for Cloud Anomaly Detection
Anomaly detection has become a key focus in maintaining the stability and reliability of the cloud environment. Although with excellent feature extraction ability, deep learning-based anomaly detection methods entail a time-consuming training process. Broad learning system (BLS) provides an alternative supervised way for efficient training. However, due to the imbalance of the collected cloud computing data in which anomaly accounts for a low proportion, sufficient feature extraction from anomaly behaviors with BLS becomes a challenge. Moreover, the input generation of BLS only considers the independence of data, and the generalization of BLS in the correlation modeling of cloud computing data is limited. To tackle the above issues, we introduce an effective anomaly detector, CatBRS, an improved BLS with rebalance operations. Initially, we employ a hybrid resampling method of SMOTE-Tomek to mitigate data imbalance, retain non-synthetic samples for training, and involve synthetic samples in the input generation later. Subsequently, we extend BLS by refining the process of input generation. This enhanced system employs a simple recurrent architecture to model temporal dynamics. Additionally, it integrates an autoencoder-based model with metric learning to obtain category-constrained discriminant features. The improvement in BLS facilitates more comprehensive feature extraction. Finally, extensive experiments are conducted to evaluate the performance of CatBRS on four benchmark datasets. CatBRS shows improvements of up to 3.81% in AUC and 6.09% in F1 compared to suboptimal baseline methods with a low training cost.
- 9 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Network and Service Management
- Vol. 22 (5) , 5015-5030
Category-Constrained Broad Recurrent System for Cloud Anomaly Detection
Anomaly detection has become a key focus in maintaining the stability and reliability of the cloud environment. Although with excellent feature extraction ability, deep learning-based anomaly detection methods entail a time-consuming training process. Broad learning system (BLS) provides an alternative supervised way for efficient training. However, due to the imbalance of the collected cloud computing data in which anomaly accounts for a low proportion, sufficient feature extraction from anomaly behaviors with BLS becomes a challenge. Moreover, the input generation of BLS only considers the independence of data, and the generalization of BLS in the correlation modeling of cloud computing data is limited. To tackle the above issues, we introduce an effective anomaly detector, CatBRS, an improved BLS with rebalance operations. Initially, we employ a hybrid resampling method of SMOTE-Tomek to mitigate data imbalance, retain non-synthetic samples for training, and involve synthetic samples in the input generation later. Subsequently, we extend BLS by refining the process of input generation. This enhanced system employs a simple recurrent architecture to model temporal dynamics. Additionally, it integrates an autoencoder-based model with metric learning to obtain category-constrained discriminant features. The improvement in BLS facilitates more comprehensive feature extraction. Finally, extensive experiments are conducted to evaluate the performance of CatBRS on four benchmark datasets. CatBRS shows improvements of up to 3.81% in AUC and 6.09% in F1 compared to suboptimal baseline methods with a low training cost.
- 23 August 2020
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 2 (9) , 3028-3038
Simultaneous Yb3+-Induced Phase Transition and Sensitized Luminescence in Er3+-Doped KNN-Based Lead-Free Ceramics for Optical Thermometry
- 23 August 2020
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 2 (9) , 3028-3038
Simultaneous Yb3+-Induced Phase Transition and Sensitized Luminescence in Er3+-Doped KNN-Based Lead-Free Ceramics for Optical Thermometry
- 28 January 2017
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 28 (10) , 7177-7183
Crystal structure and photoluminescence properties of a new phosphor Li2Sr1−xBaxSiO4:Eu2+for white LEDs
- 28 January 2017
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 28 (10) , 7177-7183
Crystal structure and photoluminescence properties of a new phosphor Li2Sr1−xBaxSiO4:Eu2+for white LEDs
- 30 October 2015
- Published by Taylor & Francis in Ferroelectrics
- Vol. 488 (1) , 54-61
Dual-Mode Luminescence, Temperature Sensing and Dielectric Performance in Pr3+/Er3+Co-Doped BaTiO3-CaTiO3Diphase Ferroelectric Oxides
Pr3+/Er3+ co-doped BaTiO3-CaTiO3 diphase ferroelectric oxides were prepared by a conventional solid-state reaction method and their phase, microstructure, photoluminescence, dielectric and ferroelectric properties were investigated by X-ray diffractometer, scanning electron microscope, electrical measurements and luminescence spectrometer etc. The result presents that a dual-mode luminescence of both a down-conversion red emission (˜612 nm) under an ultraviolet excitation and an up-conversion green emission (˜550 nm) under a near-infrared excitation in the same material of Pr3+/Er3+ co-doped BaTiO3-CaTiO3 diphase ferroelectric oxides. Meanwhile, the 405 nm (1S0→1I6), 468 nm (3P0→3H4), and 550 nm (3P0→3H5) emission lights under excitation at 213 nm are stronger than the emission under the 333 nm excitation. The ferroelectric and dielectric performances degraded with the increasing Er3+ doping concentration. These ceramics, with good temperature sensing properties, may be useful for temperature sensing devices.
- 30 October 2015
- Published by Taylor & Francis in Ferroelectrics
- Vol. 488 (1) , 54-61
Dual-Mode Luminescence, Temperature Sensing and Dielectric Performance in Pr3+/Er3+Co-Doped BaTiO3-CaTiO3Diphase Ferroelectric Oxides
Pr3+/Er3+ co-doped BaTiO3-CaTiO3 diphase ferroelectric oxides were prepared by a conventional solid-state reaction method and their phase, microstructure, photoluminescence, dielectric and ferroelectric properties were investigated by X-ray diffractometer, scanning electron microscope, electrical measurements and luminescence spectrometer etc. The result presents that a dual-mode luminescence of both a down-conversion red emission (˜612 nm) under an ultraviolet excitation and an up-conversion green emission (˜550 nm) under a near-infrared excitation in the same material of Pr3+/Er3+ co-doped BaTiO3-CaTiO3 diphase ferroelectric oxides. Meanwhile, the 405 nm (1S0→1I6), 468 nm (3P0→3H4), and 550 nm (3P0→3H5) emission lights under excitation at 213 nm are stronger than the emission under the 333 nm excitation. The ferroelectric and dielectric performances degraded with the increasing Er3+ doping concentration. These ceramics, with good temperature sensing properties, may be useful for temperature sensing devices.
- Top Cited Papers
- 10 January 2011
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 94 (2) , 348-350
Microwave Dielectric Properties of Li 2 WO 4 Ceramic with Ultra‐Low Sintering Temperature
A new ultra‐low‐temperature firing microwave dielectric ceramic, Li 2 WO 4 with the phenacite structure, was prepared via solid‐state reaction method. The Li 2 WO 4 ceramic can be well sintered at 640°–660°C, with a microwave relative permittivity ∼5.5, a Q × f value about 62 000 GHz, and a negative temperature coefficient of −146 ppm/°C at 15.7 GHz. From an X‐ray diffraction analysis, the Li 2 WO 4 ceramic was found to be chemically compatible with both silver and aluminum powders at 640°C. All the results indicate that the Li 2 WO 4 ceramic is a promising candidate for ultra‐low temperature cofired ceramic technology, especially for dielectric substrate application.
- 10 January 2011
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 94 (2) , 348-350
Top Cited PapersMicrowave Dielectric Properties of Li 2 WO 4 Ceramic with Ultra‐Low Sintering Temperature
A new ultra‐low‐temperature firing microwave dielectric ceramic, Li 2 WO 4 with the phenacite structure, was prepared via solid‐state reaction method. The Li 2 WO 4 ceramic can be well sintered at 640°–660°C, with a microwave relative permittivity ∼5.5, a Q × f value about 62 000 GHz, and a negative temperature coefficient of −146 ppm/°C at 15.7 GHz. From an X‐ray diffraction analysis, the Li 2 WO 4 ceramic was found to be chemically compatible with both silver and aluminum powders at 640°C. All the results indicate that the Li 2 WO 4 ceramic is a promising candidate for ultra‐low temperature cofired ceramic technology, especially for dielectric substrate application.
- 4 November 2010
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 93 (11) , 3686-3690
Effect of Pyrolysis Temperature on K 0.5 Na 0.5 NbO 3 Thick Films Derived from Polyvinylpyrrolidone‐Modified Chemical Solution
Lead‐free ferroelectric K 0.5 Na 0.5 NbO 3 (KNN) thick films with improved performances have been successfully prepared by polyvinylpyrrolidone‐modified chemical solution deposition method. The KNN thick films were obtained by pyrolyzing at different temperatures and annealing at 600°C. The effect of pyrolysis temperature on structures and electrical properties of KNN thick films is studied. The crystallinity of KNN films decreased with the increasing of the pyrolysis temperature, and the porous morphology is observed in the KNN films pyrolyzed at 480°C. However, the film pyrolyzed at 330°C is dense. With the analysis of X‐ray photoelectron spectroscopy for K ions, it was found that a low pyrolysis temperature favors the formation of perovskite KNN phase. Therefore, the electrical properties of the KNN films became improved at the low pyrolysis temperature. The KNN film pyrolyzed at 330°C and annealed at 600°C exhibits the large dielectric constant of 685 and low dielectric loss of 6.95%. The film also shows the saturated and symmetric polarization–electric field ( P – E ) loops with remnant polarization of 12 μC/cm 2 and piezoelectric coefficient d 33 of 56 pm/V.
- 4 November 2010
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 93 (11) , 3686-3690
Effect of Pyrolysis Temperature on K 0.5 Na 0.5 NbO 3 Thick Films Derived from Polyvinylpyrrolidone‐Modified Chemical Solution
Lead‐free ferroelectric K 0.5 Na 0.5 NbO 3 (KNN) thick films with improved performances have been successfully prepared by polyvinylpyrrolidone‐modified chemical solution deposition method. The KNN thick films were obtained by pyrolyzing at different temperatures and annealing at 600°C. The effect of pyrolysis temperature on structures and electrical properties of KNN thick films is studied. The crystallinity of KNN films decreased with the increasing of the pyrolysis temperature, and the porous morphology is observed in the KNN films pyrolyzed at 480°C. However, the film pyrolyzed at 330°C is dense. With the analysis of X‐ray photoelectron spectroscopy for K ions, it was found that a low pyrolysis temperature favors the formation of perovskite KNN phase. Therefore, the electrical properties of the KNN films became improved at the low pyrolysis temperature. The KNN film pyrolyzed at 330°C and annealed at 600°C exhibits the large dielectric constant of 685 and low dielectric loss of 6.95%. The film also shows the saturated and symmetric polarization–electric field ( P – E ) loops with remnant polarization of 12 μC/cm 2 and piezoelectric coefficient d 33 of 56 pm/V.
- 26 October 2009
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 42 (22) , 225404
Microwave dielectric properties of BaTiO3–SrZnP2O7composite ceramics for tunable microwave applications
- 26 October 2009
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 42 (22) , 225404
Microwave dielectric properties of BaTiO3–SrZnP2O7composite ceramics for tunable microwave applications
- 1 May 2008
- Published by Elsevier in Ceramics International
- Vol. 34 (4) , 901-904
Sintering behavior and microwave dielectric properties of Bi2O3–ZnO–Nb2O5-based ceramics sintered under air and N2 atmosphere
- 1 May 2008
- Published by Elsevier in Ceramics International
- Vol. 34 (4) , 901-904
Sintering behavior and microwave dielectric properties of Bi2O3–ZnO–Nb2O5-based ceramics sintered under air and N2 atmosphere