Minh Tan Nguyen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Minh Tan Nguyen has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Xuan Thanh Pham
School of Electrical and Electronic Engineering, Hanoi University of Industry, Hanoi, Vietnam
2 shared publications - Alessandro Lo Schiavo
Department of Engineering, Università degli Studi della Campania “Luigi Vanvitelli”, 81031 Aversa, Italy
1 shared publication - Cong-Kha Pham
Department of Computer and Network Engineering, The University of Electro-Communications (UEC), 1-5-1 Chofugaoka, Tokyo 182-8585, Japan
1 shared publication - Kieu-Xuan Thuc
Hanoi University of Industry, Hanoi, Vietnam
1 shared publication - Orazio Aiello
University of Genoa
1 shared publication
Latest Publications
- Open Access
- 5 February 2026
- Published by MDPI AG in Electronics
- Vol. 15 (3) , 688
A Bipolar-Output Converter with an Adaptive Ramp Generator and PWM Control for OLED Displays
Traditional power management for organic electroluminescent (OLED) displays is performed by two different converters, providing both positive and negative power rails and thus raising fabrication costs due to the usage of two inductors, in addition to efficiency being dependent on one of the two converters while also suffering from high-voltage stress. This paper introduces a bipolar converter that only uses a single inductor to generate both power rails for OLED displays, along with two additional flying capacitors to reduce inductor currents and voltage stress placed on the power switches. The proposed design implemented in the 180 nm CMOS process occupies a chip area of 0.98 mm2 and achieves a peak efficiency of 93% at 350 mA load current. Furthermore, the ripple voltage is greatly reduced using both common-mode and differential-mode feedback loops in the PWM control scheme, with a maximum ripple of 20 mV across a 100–500 mA current range.
- 5 February 2026
- Published by MDPI AG in Electronics
- Vol. 15 (3) , 688
Open AccessA Bipolar-Output Converter with an Adaptive Ramp Generator and PWM Control for OLED Displays
Traditional power management for organic electroluminescent (OLED) displays is performed by two different converters, providing both positive and negative power rails and thus raising fabrication costs due to the usage of two inductors, in addition to efficiency being dependent on one of the two converters while also suffering from high-voltage stress. This paper introduces a bipolar converter that only uses a single inductor to generate both power rails for OLED displays, along with two additional flying capacitors to reduce inductor currents and voltage stress placed on the power switches. The proposed design implemented in the 180 nm CMOS process occupies a chip area of 0.98 mm2 and achieves a peak efficiency of 93% at 350 mA load current. Furthermore, the ripple voltage is greatly reduced using both common-mode and differential-mode feedback loops in the PWM control scheme, with a maximum ripple of 20 mV across a 100–500 mA current range.
- Open Access
- 13 June 2025
- Published by MDPI AG in Electronics
- Vol. 14 (12) , 2425
Buck Converter with Improved Efficiency and Wide Load Range Enabled by Negative Level Shifter and Low-Power Adaptive On-Time Controller
This paper introduces a high-efficiency buck converter designed for a wide load range, targeting low-power applications in medical devices, smart homes, wearables, IoT, and technology utilizing WiFi and Bluetooth. To achieve high efficiency across varying loads, the proposed converter employs a low-power adaptive on-time (AOT) controller that ensures output voltage stability and seamless mode transitions. An adaptive comparator (ACP) with variable output impedance is introduced, offering a variable DC gain and bandwidth to be suitable for different load conditions. A negative-level shifter (NLS) circuit, with its swing ranging from −0.5 V to the battery voltage (VBAT), is proposed to control the smaller power p-MOS transistors. By using an NLS, the chip area, which is mostly occupied by power CMOS transistors, is reduced while the power efficiency is improved, particularly under a heavy load. A status time detector (STD) block which provides control signals to the ACP and NLS for optimized power consumption is added to identify load conditions (heavy, light, ultra-light). By employing a 180 nm CMOS technology, the active chip area occupies about 0.31 mm2. With an input voltage range of 2.8–3.3 V, the controller’s current consumption ranges from 1.2 μA to 16 μA, corresponding to the output load current varying from 12 μA to 120 mA. Although the output load can vary, the output voltage is regulated at 1.2 V with a ripple between 3 and 12 mV. The proposed design achieves a peak efficiency of 96.2% under a heavy load with a switching frequency of 1.3 MHz.
- 13 June 2025
- Published by MDPI AG in Electronics
- Vol. 14 (12) , 2425
Open AccessBuck Converter with Improved Efficiency and Wide Load Range Enabled by Negative Level Shifter and Low-Power Adaptive On-Time Controller
This paper introduces a high-efficiency buck converter designed for a wide load range, targeting low-power applications in medical devices, smart homes, wearables, IoT, and technology utilizing WiFi and Bluetooth. To achieve high efficiency across varying loads, the proposed converter employs a low-power adaptive on-time (AOT) controller that ensures output voltage stability and seamless mode transitions. An adaptive comparator (ACP) with variable output impedance is introduced, offering a variable DC gain and bandwidth to be suitable for different load conditions. A negative-level shifter (NLS) circuit, with its swing ranging from −0.5 V to the battery voltage (VBAT), is proposed to control the smaller power p-MOS transistors. By using an NLS, the chip area, which is mostly occupied by power CMOS transistors, is reduced while the power efficiency is improved, particularly under a heavy load. A status time detector (STD) block which provides control signals to the ACP and NLS for optimized power consumption is added to identify load conditions (heavy, light, ultra-light). By employing a 180 nm CMOS technology, the active chip area occupies about 0.31 mm2. With an input voltage range of 2.8–3.3 V, the controller’s current consumption ranges from 1.2 μA to 16 μA, corresponding to the output load current varying from 12 μA to 120 mA. Although the output load can vary, the output voltage is regulated at 1.2 V with a ripple between 3 and 12 mV. The proposed design achieves a peak efficiency of 96.2% under a heavy load with a switching frequency of 1.3 MHz.