Olugbenga Ayeni
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Olugbenga Ayeni has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Cenk Aktas
Chair for Multicomponent Materials Department of Materials Science Faculty of Engineering Kiel University Kaiserstraße 2 24143 Kiel Germany
1 shared publication - Franz Faupel
Kiel University
1 shared publication - Kagan Berk
Department of Orthodontics, University Hospital Schleswig Holstein, Arnold-Heller-Straße 3, 24105 Kiel, Germany
1 shared publication - Mehmet Fatih Aycan
Department of Mechanical Engineering Institute for Graduate School of Natural and Applied Sciences Gazi University Ankara Türkiye
1 shared publication - Muhammad Hassan Razzaq
Department of Mechanical Engineering, Gazi University, Yenimahalle, Ankara, 06560, Turkey
1 shared publication - Muhammad Usama Zaheer
Department of Mechanical Engineering, Institute for Graduate School of Natural and Applied Sciences, Gazi University, Ankara 06570, Türkiye
1 shared publication
Latest Publications
- Open Access
- 23 June 2025
- Published by MDPI AG in Journal of Functional Biomaterials
- Vol. 16 (7) , 230
The Impact of As-Built Surface Characteristics of Selective-Laser-Melted Ti-6Al-4V on Early Osteoblastic Response for Potential Dental Applications
This study investigates the potential of Selective Laser Melting (SLM) to tailor the surface characteristics of Ti6Al4V directly during fabrication, eliminating the need for post-processing treatments potentially for dental implants. By adjusting the Volumetric Energy Density (VED) through controlled variations in the laser scanning speed, we achieved customized surface textures at both the micro- and nanoscale levels. SLM samples fabricated at moderate VED levels (50–100 W·mm3/s) exhibited optimized dual-scale surface roughness—a macro-roughness of up to 25.5–27.6 µm and micro-roughness of as low as 58.8–64.2 nm—resulting in significantly enhanced hydrophilicity, with water contact angles (WCAs) decreasing to ~62°, compared to ~80° on a standard grade 5 machined Ti6Al4V plate. The XPS analysis revealed that the surface oxygen content remains relatively stable at low VED values, with no significant increase. The surface topography plays a significant role in influencing the WCA, particularly when the VED values are low (below 200 W·mm3/s) during SLM, indicating the dominant effect of surface morphology over chemistry in these conditions. Biological assays using osteoblast-like MG-63 cells demonstrated that these as-built SLM surfaces supported a 1.5-fold-higher proliferation and improved cytoskeletal organization relative to the control, confirming the enhanced early cellular responses. These results highlight the capability of SLM to engineer bioactive implant surfaces through process-controlled morphology and chemistry, presenting a promising strategy for the next generation of dental implants suitable for immediate placement and osseointegration.
- 23 June 2025
- Published by MDPI AG in Journal of Functional Biomaterials
- Vol. 16 (7) , 230
Open AccessThe Impact of As-Built Surface Characteristics of Selective-Laser-Melted Ti-6Al-4V on Early Osteoblastic Response for Potential Dental Applications
This study investigates the potential of Selective Laser Melting (SLM) to tailor the surface characteristics of Ti6Al4V directly during fabrication, eliminating the need for post-processing treatments potentially for dental implants. By adjusting the Volumetric Energy Density (VED) through controlled variations in the laser scanning speed, we achieved customized surface textures at both the micro- and nanoscale levels. SLM samples fabricated at moderate VED levels (50–100 W·mm3/s) exhibited optimized dual-scale surface roughness—a macro-roughness of up to 25.5–27.6 µm and micro-roughness of as low as 58.8–64.2 nm—resulting in significantly enhanced hydrophilicity, with water contact angles (WCAs) decreasing to ~62°, compared to ~80° on a standard grade 5 machined Ti6Al4V plate. The XPS analysis revealed that the surface oxygen content remains relatively stable at low VED values, with no significant increase. The surface topography plays a significant role in influencing the WCA, particularly when the VED values are low (below 200 W·mm3/s) during SLM, indicating the dominant effect of surface morphology over chemistry in these conditions. Biological assays using osteoblast-like MG-63 cells demonstrated that these as-built SLM surfaces supported a 1.5-fold-higher proliferation and improved cytoskeletal organization relative to the control, confirming the enhanced early cellular responses. These results highlight the capability of SLM to engineer bioactive implant surfaces through process-controlled morphology and chemistry, presenting a promising strategy for the next generation of dental implants suitable for immediate placement and osseointegration.