Yuchen Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yuchen Yang has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
Yiming Zeng
Anhui University
3 shared publicationsChangqing Feng
2 shared publications- Chang-Qing Feng
University of Science and Technology of China
1 shared publication - Chenxi Chen
Department of Modern Physics, State Key Laboratory of Particle Detection and Electronics, University of Science and Technology of China, Hefei, China
1 shared publication Guangli Kuang
1 shared publicationJialiang Lu
Center of Free Electron Laser and High Magnetic Field, Anhui University, Hefei, China
1 shared publication
Latest Publications
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 73 (10) , 4139-4148
Low-Dead-Time High-Precision Wave Union FPGA-Based Time-to-Digital Converters With Event-Aggregation Encoder
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 73 (10) , 4139-4148
Low-Dead-Time High-Precision Wave Union FPGA-Based Time-to-Digital Converters With Event-Aggregation Encoder
- Open Access
- 5 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Low-Dead-Time High-precision FPGA-Based Time-to-Digital Converters with Event-aggregation Encoder
The wave union (WU) method can improve the performance of time-to-digital converters (TDCs) without consuming additional logic resources, and has therefore been widely adopted in field-programmable gate array (FPGA)-TDC designs. However, the propagation requirement of the WU pulse train forces the tapped delay line (TDL) to span longer than one clock period, such that conventional encoders must introduce extra dead time to ensure correct decoding. This article presents a low-deadtime, high-precision FPGA-based TDC that combines a 4edge WU-A scheme, dual sampling, and a resource-efficient event-aggregation encoder. With the proposed eventaggregation encoding, the WU edge positions associated with different events on the TDL are aggregated and encoded with negligible additional FPGA logic-resource usage, reducing the dead time of WU-based FPGA-TDCs to one clock cycle. In addition, to address the more severe bubble errors in advanced FPGA technology nodes, we apply clock-skew-aware placement constraints to optimize the TDL clock distribution. For the first time, a 4-edge WU-A TDC is implemented within a single clock region on a 16nm UltraScale+ FPGA. The optimized design achieves an equivalent bin width of 0.9 ps and an equivalent quantization error of 0.26 ps, improving the measured timing precision to 1.45-2.19 ps.
- 5 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Open AccessLow-Dead-Time High-precision FPGA-Based Time-to-Digital Converters with Event-aggregation Encoder
The wave union (WU) method can improve the performance of time-to-digital converters (TDCs) without consuming additional logic resources, and has therefore been widely adopted in field-programmable gate array (FPGA)-TDC designs. However, the propagation requirement of the WU pulse train forces the tapped delay line (TDL) to span longer than one clock period, such that conventional encoders must introduce extra dead time to ensure correct decoding. This article presents a low-deadtime, high-precision FPGA-based TDC that combines a 4edge WU-A scheme, dual sampling, and a resource-efficient event-aggregation encoder. With the proposed eventaggregation encoding, the WU edge positions associated with different events on the TDL are aggregated and encoded with negligible additional FPGA logic-resource usage, reducing the dead time of WU-based FPGA-TDCs to one clock cycle. In addition, to address the more severe bubble errors in advanced FPGA technology nodes, we apply clock-skew-aware placement constraints to optimize the TDL clock distribution. For the first time, a 4-edge WU-A TDC is implemented within a single clock region on a 16nm UltraScale+ FPGA. The optimized design achieves an equivalent bin width of 0.9 ps and an equivalent quantization error of 0.26 ps, improving the measured timing precision to 1.45-2.19 ps.
- 18 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. PP (2771957X) , 1-4
Deformation-Resistant Broadband RFID Tag for Multidielectric-Platform Environments
This article proposes a high-performance ultrahigh frequency (UHF) radio frequency identification (RFID) tag antenna based on broadband technology. The entire dipole antenna adopts a top-bottom structure, connected by a copper pillar in the middle, with two metal wings extended beside the feed point, the inductive impedance exhibited by the copper pillar and the capacitive impedance formed by the overlapping area of the two metal wings introduce an additional resonance point, enabling the antenna to achieve a bandwidth of 66.7% ( $S11 \lt -10$ dB, 0.9–1.8 GHz). This design endows the antenna with multiplatform applicability, and the sophisticated structure grants the tag strong adaptive adjustment capability when bent. Meanwhile, by curving the current path, the antenna size is reduced to 77.5% of its original dimension while maintaining high radiation performance—these measures significantly enhance the antenna’s deformation resistance. Finally, several prototypes were fabricated and thoroughly tested. The tag antenna achieves a maximum gain of 2.03 dBi within the 902–928-MHz band. Extensive tests were also conducted on multiple dielectric platforms. Experimental results demonstrate that the proposed tag antenna can operate under multidielectric-platform conditions and complex bending scenarios (minimum bending radius of 25 mm), maintaining a reading distance of over 0.24 m. These characteristics confirm its broad application prospects.
- 18 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. PP (2771957X) , 1-4
Deformation-Resistant Broadband RFID Tag for Multidielectric-Platform Environments
This article proposes a high-performance ultrahigh frequency (UHF) radio frequency identification (RFID) tag antenna based on broadband technology. The entire dipole antenna adopts a top-bottom structure, connected by a copper pillar in the middle, with two metal wings extended beside the feed point, the inductive impedance exhibited by the copper pillar and the capacitive impedance formed by the overlapping area of the two metal wings introduce an additional resonance point, enabling the antenna to achieve a bandwidth of 66.7% ( $S11 \lt -10$ dB, 0.9–1.8 GHz). This design endows the antenna with multiplatform applicability, and the sophisticated structure grants the tag strong adaptive adjustment capability when bent. Meanwhile, by curving the current path, the antenna size is reduced to 77.5% of its original dimension while maintaining high radiation performance—these measures significantly enhance the antenna’s deformation resistance. Finally, several prototypes were fabricated and thoroughly tested. The tag antenna achieves a maximum gain of 2.03 dBi within the 902–928-MHz band. Extensive tests were also conducted on multiple dielectric platforms. Experimental results demonstrate that the proposed tag antenna can operate under multidielectric-platform conditions and complex bending scenarios (minimum bending radius of 25 mm), maintaining a reading distance of over 0.24 m. These characteristics confirm its broad application prospects.
- 1 June 2025
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 96 (6)
A dynamic adaptive readout method for readout electronics of superconducting quantum computing
Real-time control and readout are pivotal in superconducting quantum computing, given the imperative for numerous algorithms to perform quantum operations as much as possible within the qubit coherent time. Here, we specifically address the qubit readout, recognized as the most time-consuming operation within our experimental platform, and propose a dynamic adaptive readout method (DARM) to improve the performance of qubit readout. In contrast to a standard readout method (SRM) employing Gaussian Naïve Bayes as a discriminator, the DARM can demonstrate a 22.76% relative improvement on readout fidelity when the readout duration time of both methods is set to be consistent. Furthermore, the DARM can also terminate measurement pulse ahead with a 9.93% relative reduction of measurement pulse length on statistical average. The DARM is implemented on a field-programmable-gate-array-based system, and the electronic processing latency, from the digital processing unit getting the qubit signal to the valid output information, is 52 ns, which is only 4 ns longer than the SRM. Compared with the feedforward neural network readout method, the DARM can work in a pipeline mode with shorter electronic processing latency and lower electronic utilization.
- 1 June 2025
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 96 (6)
A dynamic adaptive readout method for readout electronics of superconducting quantum computing
Real-time control and readout are pivotal in superconducting quantum computing, given the imperative for numerous algorithms to perform quantum operations as much as possible within the qubit coherent time. Here, we specifically address the qubit readout, recognized as the most time-consuming operation within our experimental platform, and propose a dynamic adaptive readout method (DARM) to improve the performance of qubit readout. In contrast to a standard readout method (SRM) employing Gaussian Naïve Bayes as a discriminator, the DARM can demonstrate a 22.76% relative improvement on readout fidelity when the readout duration time of both methods is set to be consistent. Furthermore, the DARM can also terminate measurement pulse ahead with a 9.93% relative reduction of measurement pulse length on statistical average. The DARM is implemented on a field-programmable-gate-array-based system, and the electronic processing latency, from the digital processing unit getting the qubit signal to the valid output information, is 52 ns, which is only 4 ns longer than the SRM. Compared with the feedforward neural network readout method, the DARM can work in a pipeline mode with shorter electronic processing latency and lower electronic utilization.