Meisi Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Meisi Li has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Bo Li
College of Power and Energy Engineering, Harbin Engineering University, Harbin, China
2 shared publicationsLiyun Fan
College of Power and Energy Engineering, Harbin Engineering University, China
2 shared publications- Yuanqi Gu
School of Mechanical and Power Engineering, Harbin University of Science and Technology, Harbin, China
2 shared publications - Yunpeng Wei
College of Power and Energy Engineering, Harbin Engineering University, China
2 shared publications Dianhao Zhang
College of Power and Energy Engineering, Harbin Engineering University, Harbin, China
1 shared publicationJin Zhang
College of Power and Energy Engineering, Harbin Engineering University, China
1 shared publication
Latest Publications
- 11 October 2026
- Published by SAGE Publications in International Journal of Engine Research
Regulation characteristics of ultra-high-pressure injectors for wide-range fuel delivery
Wide-range fuel delivery is essential for stable combustion and precise control, yet conventional injectors suffer from low resolution and strong nonlinearity at small injection quantities. This study investigates a high-linearity injector through combined experiments and multi-physics simulation to clarify full-range fuel delivery behavior and governing mechanisms. Injection-rate measurements and a validated dynamic model reveal a nonlinear injection quantity–pulse width ( Q–PW ) response at small pulse widths and a near-linear relationship after a stable high-flow stage is established. A segmented model is therefore developed for full-range fuel delivery prediction, and the critical pulse width ( PW c ) is identified as the macroscopic boundary between the two response regions. Mechanism analysis shows that the nozzle orifice diameter dominates the wide-range delivery capability, needle lift governs linear-region response and accuracy, and inlet/outlet orifice sizes jointly determine dynamic response. Larger nozzle and outlet orifices, increased needle lift, and a smaller inlet orifice expand the high-quantity regulation range, whereas opposite trends improve small-quantity control. A larger outlet throttling orifice ( DZ ), supplemented by an appropriately sized inlet orifice (DA ), provides the optimal basis for wide-condition adaptability. Comprehensive evaluation further indicates that structural parameters affect linearity, dynamic response, and modulation range in different ways, highlighting the importance of coordinated parameter matching. This work provides a basis for full-range fuel delivery prediction, structural optimization, and precision control of advanced high-pressure injection systems.
- 11 October 2026
- Published by SAGE Publications in International Journal of Engine Research
Regulation characteristics of ultra-high-pressure injectors for wide-range fuel delivery
Wide-range fuel delivery is essential for stable combustion and precise control, yet conventional injectors suffer from low resolution and strong nonlinearity at small injection quantities. This study investigates a high-linearity injector through combined experiments and multi-physics simulation to clarify full-range fuel delivery behavior and governing mechanisms. Injection-rate measurements and a validated dynamic model reveal a nonlinear injection quantity–pulse width ( Q–PW ) response at small pulse widths and a near-linear relationship after a stable high-flow stage is established. A segmented model is therefore developed for full-range fuel delivery prediction, and the critical pulse width ( PW c ) is identified as the macroscopic boundary between the two response regions. Mechanism analysis shows that the nozzle orifice diameter dominates the wide-range delivery capability, needle lift governs linear-region response and accuracy, and inlet/outlet orifice sizes jointly determine dynamic response. Larger nozzle and outlet orifices, increased needle lift, and a smaller inlet orifice expand the high-quantity regulation range, whereas opposite trends improve small-quantity control. A larger outlet throttling orifice ( DZ ), supplemented by an appropriately sized inlet orifice (DA ), provides the optimal basis for wide-condition adaptability. Comprehensive evaluation further indicates that structural parameters affect linearity, dynamic response, and modulation range in different ways, highlighting the importance of coordinated parameter matching. This work provides a basis for full-range fuel delivery prediction, structural optimization, and precision control of advanced high-pressure injection systems.
- 19 May 2026
- Published by SAGE Publications in International Journal of Engine Research
Supply and clearance leakage characteristics of dimethyl ether in a marine high-pressure plunger pump
To promote the development of high-pressure pressurization components for dimethyl ether (DME), a coupled one-dimensional and three-dimensional simulation approach is employed to investigate the supply and clearance leakage characteristics of DME in a high-pressure plunger pump under supply pressures of 60–90 MPa and rotational speeds of 500–2500 r/min, with cavitation behavior in leakage flows examined. Results show that DME leakage during the compression stage prolongs the pressurization process, with the leakage-related delay being most pronounced at low rotational speeds. The cam angle range of the compression stage increases by approximately 2.5°CA for every 10 MPa increase in supply pressure. Leakage also accelerates the termination of the supply stage, causing an earlier transition to the expansion stage. At 500 r/min, the supply volume and specific energy consumption of DME are approximately 58% and 2.03 times those of diesel, respectively, increasing to 92.47% and decreasing to 1.26 times at 2500 r/min. During leakage, diesel remains in the liquid phase, whereas DME undergoes pronounced cavitation within the annular groove and cylindrical channel, primarily driven by flow separation and local pressure fluctuations. Increasing the return pressure and reducing the inclination angle of the annular groove effectively suppress cavitation intensity, reducing the vapor volume fraction by more than 65% and thereby mitigating cavitation risk in high-pressure plunger pump operating with DME.
- 19 May 2026
- Published by SAGE Publications in International Journal of Engine Research
Supply and clearance leakage characteristics of dimethyl ether in a marine high-pressure plunger pump
To promote the development of high-pressure pressurization components for dimethyl ether (DME), a coupled one-dimensional and three-dimensional simulation approach is employed to investigate the supply and clearance leakage characteristics of DME in a high-pressure plunger pump under supply pressures of 60–90 MPa and rotational speeds of 500–2500 r/min, with cavitation behavior in leakage flows examined. Results show that DME leakage during the compression stage prolongs the pressurization process, with the leakage-related delay being most pronounced at low rotational speeds. The cam angle range of the compression stage increases by approximately 2.5°CA for every 10 MPa increase in supply pressure. Leakage also accelerates the termination of the supply stage, causing an earlier transition to the expansion stage. At 500 r/min, the supply volume and specific energy consumption of DME are approximately 58% and 2.03 times those of diesel, respectively, increasing to 92.47% and decreasing to 1.26 times at 2500 r/min. During leakage, diesel remains in the liquid phase, whereas DME undergoes pronounced cavitation within the annular groove and cylindrical channel, primarily driven by flow separation and local pressure fluctuations. Increasing the return pressure and reducing the inclination angle of the annular groove effectively suppress cavitation intensity, reducing the vapor volume fraction by more than 65% and thereby mitigating cavitation risk in high-pressure plunger pump operating with DME.
- 20 June 2025
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 26 (12) , 1978-1995
Study on leakage characteristics of ammonia fuel in high-pressure pump
Ammonia fuel plays a critical role in the achieving zero carbon emission in the field of internal combustion engines, and its physical properties different from traditional fuels put forward higher requirements for the supply performance and reliability of ammonia fuel high-pressure pumps. As the key to affecting the efficiency of ammonia pumps, the issue of fuel leakage has received considerable critical attention. A combination of experiment and simulation methods was used in study to obtain leakage characteristics of high-power ammonia fuel pump. The effects of fuel properties, working conditions and structure of ammonia pump on leakage characteristics are analyzed. The results indicate that ammonia fuel exhibits a slower pressure buildup rate compared to diesel, and leaks significantly more—over ten times as much. High pressure can cause the pump parts to deform, increasing plunger pair gap and leading to further leakage. When the gap is too large, the ammonia pump stops supplying liquid before the plunger reaches the maximum lift, resulting in an inefficient liquid supply process. Moreover, when the plunger pair gap exceeds 0.005 mm, leakage significantly impacts performance. Fuel temperature also affects leakage, showing a nonlinear relationship with it. The change in the volume efficiency of the ammonia pump under various operating conditions is mainly due to the loss of leakage volume efficiency. The motor control pump system achieves high volume efficiency for high-pressure ammonia pumps, ranging from 83.2% to 98.9% under full operating conditions. Through the analysis of the ammonia inlet boundary conditions, it is concluded that the ammonia inlet temperature only affects the volumetric efficiency of the ammonia pump, and the ammonia inlet pressure only affects the temperature rise of the ammonia pump system. Thus, the temperature and pressure of inlet ammonia can be managed to optimize pump performance independently.
- 20 June 2025
- Published by SAGE Publications in International Journal of Engine Research
- Vol. 26 (12) , 1978-1995
Study on leakage characteristics of ammonia fuel in high-pressure pump
Ammonia fuel plays a critical role in the achieving zero carbon emission in the field of internal combustion engines, and its physical properties different from traditional fuels put forward higher requirements for the supply performance and reliability of ammonia fuel high-pressure pumps. As the key to affecting the efficiency of ammonia pumps, the issue of fuel leakage has received considerable critical attention. A combination of experiment and simulation methods was used in study to obtain leakage characteristics of high-power ammonia fuel pump. The effects of fuel properties, working conditions and structure of ammonia pump on leakage characteristics are analyzed. The results indicate that ammonia fuel exhibits a slower pressure buildup rate compared to diesel, and leaks significantly more—over ten times as much. High pressure can cause the pump parts to deform, increasing plunger pair gap and leading to further leakage. When the gap is too large, the ammonia pump stops supplying liquid before the plunger reaches the maximum lift, resulting in an inefficient liquid supply process. Moreover, when the plunger pair gap exceeds 0.005 mm, leakage significantly impacts performance. Fuel temperature also affects leakage, showing a nonlinear relationship with it. The change in the volume efficiency of the ammonia pump under various operating conditions is mainly due to the loss of leakage volume efficiency. The motor control pump system achieves high volume efficiency for high-pressure ammonia pumps, ranging from 83.2% to 98.9% under full operating conditions. Through the analysis of the ammonia inlet boundary conditions, it is concluded that the ammonia inlet temperature only affects the volumetric efficiency of the ammonia pump, and the ammonia inlet pressure only affects the temperature rise of the ammonia pump system. Thus, the temperature and pressure of inlet ammonia can be managed to optimize pump performance independently.