TPTim Pittrich

Tim Pittrich

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Tim Pittrich has a total of 7 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Analysis of Thermohydraulic Spalling in Blended Cement Concrete

    by Tim Pittrich, Frank Dehn, Frank Weise, Ludwig Stelzner

    Recently, the construction industry has increasingly focused on the development of more sustainable transport infrastructure, such as tunnels, driven by the growing use of clinker-reduced cements. One major challenge in this context is fire exposure, which can lead to severe structural damage through concrete spalling, thereby compromising the integrity of the structure. To date, the fire-induced spalling behavior of blended cement concrete remains insufficiently understood. This is particularly concerning, given the increasing adoption of blended cements with reduced clinker content, which are expected to see widespread use in the future. Consequently, a deeper understanding of how different cement types influence spalling susceptibility is of great importance. A comprehensive study was conducted to investigate spalling behavior and analyze the associated thermohydraulic effects in concretes made with CEM I, CEM II/A-LL, CEM III/A, and CEM II/B-Q. The findings revealed that the use of blended cements generally led to increased spalling susceptibility, even in normal-strength concrete. Additional analysis indicated that blended cement concretes exhibited lower permeability and higher moisture content, both of which are likely contributors to the elevated spalling risk. Furthermore, the study showed that moisture transport during heating closely follows the dehydration behavior of the cementitious matrix. Blended cement pastes were found to contain lower quantities of early-dehydrating AFt and AFm phases, as well as more thermally stable C-(A)-S-H phases. Moreover, the incorporation of polypropylene fibers into the concrete mix effectively mitigated spalling across all cement types. Therefore, demonstrating the continued effectiveness of polypropylene fibers as a spalling prevention strategy.

  • Open Access

    Thermally induced moisture transport in concrete with different types of blended Portland cement studied by 1H-NMR relaxometry

    by Tim Pittrich, Simon Peters, Günther Meschke, Frank Weise, Ludwig Stelzner

    Clinker-reduced cements are gaining in popularity as part of efforts to lower the construction industry’s CO 2 footprint. Past studies showed that utilization of these cements negatively influences the fire-induced spalling behavior of concrete, which is highly influenced by thermohydraulic damage mechanisms. Therefore, thermally induced moisture transport in normal strength concretes made with different types of blended cements (CEM I, CEM II/A-LL, CEM III/A and CEM II/B-Q) was investigated by means of 1 H-NMR relaxometry in combination with supportive side investigations concerning permeability and porosity. In addition, a numerical model was used to analyze in-situ moisture development during high temperature exposure. The results show that the cement type influences both initial moisture content and pore size-specific moisture distribution. This was primarily reflected in an increased water content in CEM III/A and CEM II/B-Q concretes as well as a comparable high gel pore water fraction in CEM II/B-Q concrete before heating. After heating, a similar degree of pore coarsening from gel to capillary pore was observed in all samples. Although the measurements were only conducted after, not during, high temperature exposure, the depth of the drying front and the extent of the moisture clog could be determined. With the additional numerical analysis, it can be assumed that during high temperature load, the drying front is less advanced and the moisture clog even more pronounced. In conclusion, it can be stated that the increased spalling susceptibility in blended cement concrete is caused by the lower initial permeability and increased moisture content.


  • Open Access

    Thermally induced moisture transport in concrete with different types of blended Portland cement studied by 1H-NMR relaxometry

    by Tim Pittrich, Simon Peters, Günther Meschke, Frank Weise, Ludwig Stelzner

    Clinker-reduced cements are gaining in popularity as part of efforts to lower the construction industry’s CO 2 footprint. Past studies showed that utilization of these cements negatively influences the fire-induced spalling behavior of concrete, which is highly influenced by thermohydraulic damage mechanisms. Therefore, thermally induced moisture transport in normal strength concretes made with different types of blended cements (CEM I, CEM II/A-LL, CEM III/A and CEM II/B-Q) was investigated by means of 1 H-NMR relaxometry in combination with supportive side investigations concerning permeability and porosity. In addition, a numerical model was used to analyze in-situ moisture development during high temperature exposure. The results show that the cement type influences both initial moisture content and pore size-specific moisture distribution. This was primarily reflected in an increased water content in CEM III/A and CEM II/B-Q concretes as well as a comparable high gel pore water fraction in CEM II/B-Q concrete before heating. After heating, a similar degree of pore coarsening from gel to capillary pore was observed in all samples. Although the measurements were only conducted after, not during, high temperature exposure, the depth of the drying front and the extent of the moisture clog could be determined. With the additional numerical analysis, it can be assumed that during high temperature load, the drying front is less advanced and the moisture clog even more pronounced. In conclusion, it can be stated that the increased spalling susceptibility in blended cement concrete is caused by the lower initial permeability and increased moisture content.


  • Open Access

    The impact of blended cements on the spalling behavior of concrete at elevated temperatures: a review

    by Tim Pittrich, Frank Weise, Ludwig Stelzner

    The cement and concrete industries are striving to reduce the CO2 emissions caused by the production of Portland cement. An effective way to achieve this is to replace Portland cement clinker with more environmentally friendly supplementary cementitious materials (SCMs) to produce blended cements. A variety of different SCMs are used today, from fly ash to more exotic options such as rice husk ash or waste glass powder. Depending on its material properties, concrete exposed to fire may experience spalling caused by thermomechanical and thermohydraulic mechanisms. Severe spalling leads to a reduction in the cross-section and exposure of the reinforcement, jeopardizing the load-bearing capacity of the concrete element. The use of blended cements changes the concrete properties which can affect spalling behavior at high temperatures. The link between high temperature and spalling behavior of concrete with blended cements has been investigated in several studies. A review of the existing literature led to the conclusion that the cement type influences the spalling behavior of concrete. However, the relationship does not appear to be clear, as there are contradictions and inconsistencies between the evaluated results. Therefore, further in-depth studies will help to gain a more precise understanding of the effects of blended cements on the spalling behavior of concrete at elevated temperatures.