Nan Lu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Nan Lu has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Zhe Wang
Lishui University
2 shared publications Dazhi Wu
School of Civil Engineering and Architecture, Zhejiang Sci-Tech University, Hangzhou, China
1 shared publication- Hanwen Zhang
Faculty of Science and Engineering, University of Nottingham Ningbo, Ningbo 315100, China
1 shared publication Junyi Huang
School of Civil Engineering and Architecture, Zhejiang Sci-Tech University, Hangzhou, China
1 shared publicationPan Zhou
Department of Civil Engineering, Faculty of Engineering, Lishui University, Lishui, China
1 shared publicationShu Liu
Department of Civil Engineering, International Doctoral Innovation Centre, University of Nottingham, Ningbo, China
1 shared publication
Latest Publications
- Open Access
- 28 November 2025
- Published by Frontiers Media SA in Frontiers in Earth Science
- Vol. 13, 1687298
Experimental investigation on the construction waste recycled sand reinforced by soybean urease-induced calcium carbonate precipitation
Recycled sand from construction waste presents a promising substitute for natural sand. However, such sand typically exhibits low strength, high crushing index, and poor grading, which collectively compromise its performance in subgrade applications subjected to cyclic shear stresses caused by wave, seismic, and traffic loads. This study investigates the application of Soybean Urease-Induced Calcium Carbonate Precipitation (SICP) method to enhance the engineering properties of recycled sands. Firstly, several factors influencing the precipitation process are examined, including soybean powder concentration, cementation solution concentration and the ratio between urea and calcium chloride. Subsequently, unconfined compressive tests are conducted on sands reinforced under various conditions. Results indicate that the sample strength increases significantly with higher cementation solution concentration and grouting frequency; however, excessively high concentrations lead to a decline in sample strength, likely due to the reduced calcium carbonate precipitation efficiency under supersaturated conditions. Scanning electron microscopy reveals that the reinforcing effect can be attributed to calcium carbonate crystals formed between particles, which function as binding agents for the recycled sands.
- 28 November 2025
- Published by Frontiers Media SA in Frontiers in Earth Science
- Vol. 13, 1687298
Open AccessExperimental investigation on the construction waste recycled sand reinforced by soybean urease-induced calcium carbonate precipitation
Recycled sand from construction waste presents a promising substitute for natural sand. However, such sand typically exhibits low strength, high crushing index, and poor grading, which collectively compromise its performance in subgrade applications subjected to cyclic shear stresses caused by wave, seismic, and traffic loads. This study investigates the application of Soybean Urease-Induced Calcium Carbonate Precipitation (SICP) method to enhance the engineering properties of recycled sands. Firstly, several factors influencing the precipitation process are examined, including soybean powder concentration, cementation solution concentration and the ratio between urea and calcium chloride. Subsequently, unconfined compressive tests are conducted on sands reinforced under various conditions. Results indicate that the sample strength increases significantly with higher cementation solution concentration and grouting frequency; however, excessively high concentrations lead to a decline in sample strength, likely due to the reduced calcium carbonate precipitation efficiency under supersaturated conditions. Scanning electron microscopy reveals that the reinforcing effect can be attributed to calcium carbonate crystals formed between particles, which function as binding agents for the recycled sands.
- Open Access
Numerical Simulation of Principal Stress Axes Rotation in Clay with an Anisotropic Bounding Surface Model Incorporating a Relocatable Mapping Center
In engineering practice, soils will inevitably experience some rotation of principal stress directions. Recent experimental evidence has highlighted how principal stress axes rotation significantly impacts clay behavior. However, most existing constitutive models accounting for this effect are essentially designed for sand and may not be applicable to clays. This paper introduces an anisotropic bounding surface model to reproduce the response of clay to principal stress axes rotation. The model’s key innovation lies in its incorporation of a secondary mapping procedure in the deviatoric stress ratio plane, which utilizes a relocatable mapping center. This step is a complement to the conventional radial mapping procedure in the meridional plane, which utilizes a fixed mapping center. This constitutive enhancement facilitates the precise modeling of plastic deformation triggered by the rotation of principal stress axes, without introducing additional loading mechanisms or incremental stress–strain nonlinearity. The performance of the model is first evaluated under various conditions and then verified through comparisons between simulation results and experimental data. The results demonstrate the effectiveness of the model and underscore the necessity of incorporating stress rotation effects into the constitutive modeling of clay.
Open AccessNumerical Simulation of Principal Stress Axes Rotation in Clay with an Anisotropic Bounding Surface Model Incorporating a Relocatable Mapping Center
In engineering practice, soils will inevitably experience some rotation of principal stress directions. Recent experimental evidence has highlighted how principal stress axes rotation significantly impacts clay behavior. However, most existing constitutive models accounting for this effect are essentially designed for sand and may not be applicable to clays. This paper introduces an anisotropic bounding surface model to reproduce the response of clay to principal stress axes rotation. The model’s key innovation lies in its incorporation of a secondary mapping procedure in the deviatoric stress ratio plane, which utilizes a relocatable mapping center. This step is a complement to the conventional radial mapping procedure in the meridional plane, which utilizes a fixed mapping center. This constitutive enhancement facilitates the precise modeling of plastic deformation triggered by the rotation of principal stress axes, without introducing additional loading mechanisms or incremental stress–strain nonlinearity. The performance of the model is first evaluated under various conditions and then verified through comparisons between simulation results and experimental data. The results demonstrate the effectiveness of the model and underscore the necessity of incorporating stress rotation effects into the constitutive modeling of clay.