Jianping Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jianping Li has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Hongbo Duan
University of Chinese Academy of Sciences (UCAS), Beijing, China
2 shared publications - Zhong Yang
School of Materials and Chemical Engineering, Xi’an Technological University, Xi’an 710021, China
2 shared publications - Chao Wu
School of Material Science and Technology, Nanjing Institute of Technology, Nanjing 211167, China
1 shared publication - Hiroshi Moriyama
Department of Neurosurgery, Graduate School of Medicine, Yamaguchi University, Ube, Yamaguchi, 755-8505, Japan
1 shared publication - Juan Wang
School of Intelligent Manufacturing and Elevator, Huzhou Vocational & Technical College, Huzhou 313000, China
1 shared publication Li Yuan
1 shared publication
Latest Publications
- 9 October 2026
- Published by Elsevier in Intermetallics
- Vol. 199
Machine learning guided design and deformation mechanisms of dual-phase Al0.4Co0.5VxFeNi high-entropy alloys
- 9 October 2026
- Published by Elsevier in Intermetallics
- Vol. 199
Machine learning guided design and deformation mechanisms of dual-phase Al0.4Co0.5VxFeNi high-entropy alloys
- Open Access
- 17 November 2023
- Published by Elsevier in Materials & Design
- Vol. 236, 112493
The nanocrystalline and high density dislocation-Enabled ultrahigh strength and ductility of Al0.4Co0.5V0.2FeNi high entropy alloy
- 17 November 2023
- Published by Elsevier in Materials & Design
- Vol. 236, 112493
Open AccessThe nanocrystalline and high density dislocation-Enabled ultrahigh strength and ductility of Al0.4Co0.5V0.2FeNi high entropy alloy
- 10 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1063-1067
Influence of Ce Content on the Microstructure and Microhardness of Injection Casting Al-Cu-Fe Alloys
The quasicrystal alloys are novel materials, which can be used in several regions of highly developed technology. In this study, quasicrystal alloy (Al 63 Cu 25 Fe 12 ) 100-x Ce x (x =2, 3, 5 and 7 at%) was prepared by copper mold spray casting process. The effects of Ce addition on the microstructure and microhardness of the alloy were analyzed by scanning electron microscope, energy dispersive spectrometer (EDS) and X-ray diffraction. The results show that the appropriate amount of Ce can improve the microstructure distribution of the alloy to a great extent. With the increase of Ce content, the microhardness value of the alloy first increases to the maximum and then decreases gradually. When the content of Ce is 3 at%, the microhardness of the alloy is the largest, and the microstructure of the alloy is evenly distributed and the grains are fine. At the same time, with the increase of Ce content, the formation of icosahedral quasicrystal I-phase (I-phase) decreases, and the morphology of AlCeCu phase changes from fine rod to small block, then to ellipsoid or maple leaf, and then to fine rod. The use of the injection casting method and the addition of an appropriate amount of Ce can potentially help design and develop Al-Cu-Fe-Ce alloys.
- 10 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1063-1067
Influence of Ce Content on the Microstructure and Microhardness of Injection Casting Al-Cu-Fe Alloys
The quasicrystal alloys are novel materials, which can be used in several regions of highly developed technology. In this study, quasicrystal alloy (Al 63 Cu 25 Fe 12 ) 100-x Ce x (x =2, 3, 5 and 7 at%) was prepared by copper mold spray casting process. The effects of Ce addition on the microstructure and microhardness of the alloy were analyzed by scanning electron microscope, energy dispersive spectrometer (EDS) and X-ray diffraction. The results show that the appropriate amount of Ce can improve the microstructure distribution of the alloy to a great extent. With the increase of Ce content, the microhardness value of the alloy first increases to the maximum and then decreases gradually. When the content of Ce is 3 at%, the microhardness of the alloy is the largest, and the microstructure of the alloy is evenly distributed and the grains are fine. At the same time, with the increase of Ce content, the formation of icosahedral quasicrystal I-phase (I-phase) decreases, and the morphology of AlCeCu phase changes from fine rod to small block, then to ellipsoid or maple leaf, and then to fine rod. The use of the injection casting method and the addition of an appropriate amount of Ce can potentially help design and develop Al-Cu-Fe-Ce alloys.
- 10 August 2012
- Published by Wiley in Journal of Polymer Science Part B: Polymer Physics
- Vol. 50 (20) , 1426-1432
Synthesis and characterization of C60/polyaniline composites from interfacial polymerization
- 10 August 2012
- Published by Wiley in Journal of Polymer Science Part B: Polymer Physics
- Vol. 50 (20) , 1426-1432
Synthesis and characterization of C60/polyaniline composites from interfacial polymerization