Taizo Kanai
Research Subjects
Taizo Kanai has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Masahiro Furuya
Faculty of Advanced Science and Engineering, Waseda University, Tokyo 162-0041, Japan
2 shared publications Antonin Bouland
1 shared publicationArthur Denoix
1 shared publication- CélIa Guevar1 shared publication
- Christophe Journeau
CEA, DES, IRESNE, DTN, Severe Accident Experimental Laboratory
1 shared publication Emmanuel Porcheron
1 shared publication
Latest Publications
- Open Access
- 4 September 2026
- Published by Elsevier in SSRN Electronic Journal
Fuel debris prototype fabrication and cutting in view of determining airborne release fraction for Fukushima Daiichi fuel debris retrieval
Estimating the Airborne Release Fraction (ARF) during fuel debris (FD) retrieval is important for the safe decommissioning of the Fukushima Daiichi Nuclear Power Plant (1F) because it supports exposure assessment and the design of mitigation measures. Dust generation during dry mechanical cutting depends not only on operating conditions but also strongly on the properties of the cut material, including size, geometry, mechanical behavior and multiphase heterogeneity. Therefore, representative simulants are required to obtain reliable datasets. In the CRIEPI-led Dust Acquisition project, this paper focuses on the design and kilogram-scale fabrication of uranium-bearing FD simulants representative of major in-vessel and ex-vessel debris conditions at 1F. Five simulants were manufactured at CEA using thermite reactions, direct induction heating or combined processing, depending on thermochemical constraints and target compositions. A representative manufacturing example is presented to illustrate composition selection and optimization of thermite reaction in order to obtain complete melting and coherent blocks at the kilogram scale. As a result of this project and previously manufactured compositions in URASOL IRID-JAEA/CLADS project, some of the five FD representative blocks with multiphase (U-Zr-O oxide matrices with metallic inclusions and MCCI-like silicate-rich phases) and non-uniform aspect have been selected. Main features of the blocks are presented. They provide realistic FD for generation of aerosols by dry disc cutting on FUJISAN2 facility, designed within a collaboration between CRIEPI, ONET, CEA, and IRSN (now ASNR). Physical and chemical characterization of aerosols techniques are shortly presented.
- 4 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessFuel debris prototype fabrication and cutting in view of determining airborne release fraction for Fukushima Daiichi fuel debris retrieval
Estimating the Airborne Release Fraction (ARF) during fuel debris (FD) retrieval is important for the safe decommissioning of the Fukushima Daiichi Nuclear Power Plant (1F) because it supports exposure assessment and the design of mitigation measures. Dust generation during dry mechanical cutting depends not only on operating conditions but also strongly on the properties of the cut material, including size, geometry, mechanical behavior and multiphase heterogeneity. Therefore, representative simulants are required to obtain reliable datasets. In the CRIEPI-led Dust Acquisition project, this paper focuses on the design and kilogram-scale fabrication of uranium-bearing FD simulants representative of major in-vessel and ex-vessel debris conditions at 1F. Five simulants were manufactured at CEA using thermite reactions, direct induction heating or combined processing, depending on thermochemical constraints and target compositions. A representative manufacturing example is presented to illustrate composition selection and optimization of thermite reaction in order to obtain complete melting and coherent blocks at the kilogram scale. As a result of this project and previously manufactured compositions in URASOL IRID-JAEA/CLADS project, some of the five FD representative blocks with multiphase (U-Zr-O oxide matrices with metallic inclusions and MCCI-like silicate-rich phases) and non-uniform aspect have been selected. Main features of the blocks are presented. They provide realistic FD for generation of aerosols by dry disc cutting on FUJISAN2 facility, designed within a collaboration between CRIEPI, ONET, CEA, and IRSN (now ASNR). Physical and chemical characterization of aerosols techniques are shortly presented.
- Open Access
- 28 November 2025
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 446
Experimental study of Gas-Water Two-Phase flow in a bubble Column: Insights into the Transition and structure of flow in pool scrubbing tests
- 28 November 2025
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 446
Open AccessExperimental study of Gas-Water Two-Phase flow in a bubble Column: Insights into the Transition and structure of flow in pool scrubbing tests
- Open Access
- 8 July 2025
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 443
Experimental study on iodine decontamination efficiency in NaOH and Na2S2O3-NaOH mixed solutions at 30–40°C and atmospheric pressure
- 8 July 2025
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 443
Open AccessExperimental study on iodine decontamination efficiency in NaOH and Na2S2O3-NaOH mixed solutions at 30–40°C and atmospheric pressure