Yonglin Min
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yonglin Min has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Gang Jin
College of Mechanical Engineering, Tianjin University of Technology and Education, Tianjin 300222, China
4 shared publications - Chong Li
Tianjin University of Technology and Education, Tianjin, China
2 shared publications - Desheng Li
Tianjin University of Technology and Education, Tianjin, China
2 shared publications - Mengpan Hu
Tianjin University of Technology and Education, Tianjin, China
2 shared publications - Yipu Bian
Tianjin University of Technology and Education, Tianjin, China
2 shared publications - Zhanjie Li
College of Mechanical Engineering, Tianjin University of Technology and Education, Tianjin 300222, China
2 shared publications
Latest Publications
- Open Access
- 11 September 2026
- Published by MDPI AG in Micromachines
- Vol. 17 (9) , 1076
Atomic-Scale Mechanisms of Ultrasonic-Assisted Ultra-Precision Cutting of W-Mo70 Alloy: Experimental Benchmarking and Molecular Dynamics Simulation
W-Mo70 alloys feature high hardness, a high melting point and poor machinability, resulting in large cutting loads and complex subsurface plastic deformation during ultra-precision machining. To reveal the atomic-scale mechanism by which ultrasonic elliptical vibration regulates material removal and defect evolution, three-dimensional molecular dynamics (MD) models of conventional cutting (CC) and ultrasonic elliptical vibration cutting (UEVC) were established with previously published ultra-precision turning experiments as the macroscopic benchmark. The material removal behavior, cutting force response, interfacial loading characteristics and dislocation evolution law were systematically analyzed. The results show that UEVC exhibits a reduction trend in the cycle-averaged main cutting force compared with CC, which is qualitatively consistent with the experimental trend. However, the reduction magnitude should not be directly compared with experimental results because of the significant differences in machining scale, cutting velocity, strain rate, and tool geometry between MD simulations and experiments. The average normal force remains nearly unchanged but exhibits a significant vibration-induced transient loading–unloading response. Under UEVC, dislocation evolution transforms from continuous accumulation under CC to transient activation at the high-load stage and defect reorganization during the unloading stage. This study reveals the atomic-scale mechanism of UEVC characterized by a vibration-induced transient loading–unloading response, interfacial unloading, defect reorganization and phase-dependent localized material removal, providing atomic-level theoretical support for subsurface defect regulation in ultra-precision cutting of difficult-to-machine W-Mo alloys.
- 11 September 2026
- Published by MDPI AG in Micromachines
- Vol. 17 (9) , 1076
Open AccessAtomic-Scale Mechanisms of Ultrasonic-Assisted Ultra-Precision Cutting of W-Mo70 Alloy: Experimental Benchmarking and Molecular Dynamics Simulation
W-Mo70 alloys feature high hardness, a high melting point and poor machinability, resulting in large cutting loads and complex subsurface plastic deformation during ultra-precision machining. To reveal the atomic-scale mechanism by which ultrasonic elliptical vibration regulates material removal and defect evolution, three-dimensional molecular dynamics (MD) models of conventional cutting (CC) and ultrasonic elliptical vibration cutting (UEVC) were established with previously published ultra-precision turning experiments as the macroscopic benchmark. The material removal behavior, cutting force response, interfacial loading characteristics and dislocation evolution law were systematically analyzed. The results show that UEVC exhibits a reduction trend in the cycle-averaged main cutting force compared with CC, which is qualitatively consistent with the experimental trend. However, the reduction magnitude should not be directly compared with experimental results because of the significant differences in machining scale, cutting velocity, strain rate, and tool geometry between MD simulations and experiments. The average normal force remains nearly unchanged but exhibits a significant vibration-induced transient loading–unloading response. Under UEVC, dislocation evolution transforms from continuous accumulation under CC to transient activation at the high-load stage and defect reorganization during the unloading stage. This study reveals the atomic-scale mechanism of UEVC characterized by a vibration-induced transient loading–unloading response, interfacial unloading, defect reorganization and phase-dependent localized material removal, providing atomic-level theoretical support for subsurface defect regulation in ultra-precision cutting of difficult-to-machine W-Mo alloys.
- 24 February 2026
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (25) , 1-15
Study on Scratch Behavior and Material Removal of WCu20 Alloy Single Particles under Acoustic-Electrical Synergy
- 24 February 2026
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (25) , 1-15
Study on Scratch Behavior and Material Removal of WCu20 Alloy Single Particles under Acoustic-Electrical Synergy
- 29 December 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (19) , 19013-19031
Mechanical Properties and JC Constitutive Modification of TNZ1313 Titanium Alloys Considering High Strain Rates and High/Low Temperatures
- 29 December 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (19) , 19013-19031
Mechanical Properties and JC Constitutive Modification of TNZ1313 Titanium Alloys Considering High Strain Rates and High/Low Temperatures
- Open Access
A Research Method to Investigate the Effect of Vibration Suppression on Thin-Walled Parts of Aluminum Alloy 6061 Based on Cutting Fluid Spraying (CFS)
This study aims to address the issues of high tool wear rate, severe deterioration of machining accuracy, and surface integrity in thin-walled part cutting processes, which are caused by vibration. To do so, this paper proposes a thin-walled part processing vibration control method based on CFS. With aluminum alloy 6061 planar thin-walled parts as the object of study, in this paper a CFS experimental platform was established, the influence of CFS on the dynamic characteristics of the thin-walled parts was analyzed, the effects of milling force and processing vibration during thin-walled part milling were investigated. The results show that compared with UCFS, CFS can significantly reduce the acceleration response amplitude of thin-walled parts and shorten their vibration decay time. When the spraying point coincides with the hammering point, the optimal vibration suppression effect is achieved at a spraying velocity V of 13 m/s, a spraying area S of 31 mm2, and a spraying angle θ of 30°; the acceleration response amplitude decreases by 76.2%, and the vibration attenuation time decreases by 74.7%. This method can provide a certain support force and damping effect for thin-walled parts by CFS, thus reducing the milling force and machining vibration.
Open AccessA Research Method to Investigate the Effect of Vibration Suppression on Thin-Walled Parts of Aluminum Alloy 6061 Based on Cutting Fluid Spraying (CFS)
This study aims to address the issues of high tool wear rate, severe deterioration of machining accuracy, and surface integrity in thin-walled part cutting processes, which are caused by vibration. To do so, this paper proposes a thin-walled part processing vibration control method based on CFS. With aluminum alloy 6061 planar thin-walled parts as the object of study, in this paper a CFS experimental platform was established, the influence of CFS on the dynamic characteristics of the thin-walled parts was analyzed, the effects of milling force and processing vibration during thin-walled part milling were investigated. The results show that compared with UCFS, CFS can significantly reduce the acceleration response amplitude of thin-walled parts and shorten their vibration decay time. When the spraying point coincides with the hammering point, the optimal vibration suppression effect is achieved at a spraying velocity V of 13 m/s, a spraying area S of 31 mm2, and a spraying angle θ of 30°; the acceleration response amplitude decreases by 76.2%, and the vibration attenuation time decreases by 74.7%. This method can provide a certain support force and damping effect for thin-walled parts by CFS, thus reducing the milling force and machining vibration.