Hao Chang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hao Chang has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Chengwen Sun
College of Mechanical and Electrical Engineering, Northeast Forestry University, Harbin 150006, China
1 shared publication - Chunmei Yang
College of Mechanical and Electrical Engineering, Northeast Forestry University, Harbin 150040, China
1 shared publication - Jie Yan
Forestry and Woodworking Machinery Engineering Technology Center, Northeast Forestry University, Harbin 150006, China
1 shared publication - Jiuqing Liu
College of Mechanical and Electrical Engineering, Northeast Forestry University, Harbin, China
1 shared publication - Xin Sun
Forestry and Woodworking Machinery Engineering Technology Center, Northeast Forestry University, Harbin 150006, China
1 shared publication - Xingchen Ding
Forestry and Woodworking Machinery Engineering Technology Center, Northeast Forestry University, Harbin 150006, China
1 shared publication
Latest Publications
- Open Access
- 31 July 2025
- Published by MDPI AG in Technologies
- Vol. 13 (8) , 324
Design of a Bidirectional Veneer Defect Repair Method Based on Parametric Modeling and Multi-Objective Optimization
Repairing veneer defects is the key to ensuring the quality of plywood. In order to improve the maintenance quality and material utilization efficiency during the maintenance process, this paper proposes a bidirectional maintenance method based on gear rack transmission and its related equipment. Based on the working principle, a geometric relationship model was established, which combines the structural parameters of the mold, punch, and gear system. Simultaneously, it solves the problem of motion attitude analysis of conjugate tooth profiles under non-standard meshing conditions, aiming to establish a constraint relationship between stamping motion and structural design parameters. On this basis, a constrained optimization model was developed by integrating multi-objective optimization theory to maximize maintenance efficiency. The NSGA-III algorithm is used to solve the model and obtain the Pareto front solution set. Subsequently, three optimal parameter configurations were selected for simulation analysis and experimental platform construction. The simulation and experimental results indicate that the veneer repair time ranges from 0.6 to 1.8 seconds, depending on the stamping speed. A reduction of 28 mm in die height decreases the repair time by approximately 0.1 seconds, resulting in an efficiency improvement of about 14%. The experimental results confirm the effectiveness of the proposed method in repairing veneer defects. Vibration measurements further verify the system’s stable operation under parametric modeling and optimization design. The main vibration response occurs during the meshing and disengagement phases between the gear and rack.
- 31 July 2025
- Published by MDPI AG in Technologies
- Vol. 13 (8) , 324
Open AccessDesign of a Bidirectional Veneer Defect Repair Method Based on Parametric Modeling and Multi-Objective Optimization
Repairing veneer defects is the key to ensuring the quality of plywood. In order to improve the maintenance quality and material utilization efficiency during the maintenance process, this paper proposes a bidirectional maintenance method based on gear rack transmission and its related equipment. Based on the working principle, a geometric relationship model was established, which combines the structural parameters of the mold, punch, and gear system. Simultaneously, it solves the problem of motion attitude analysis of conjugate tooth profiles under non-standard meshing conditions, aiming to establish a constraint relationship between stamping motion and structural design parameters. On this basis, a constrained optimization model was developed by integrating multi-objective optimization theory to maximize maintenance efficiency. The NSGA-III algorithm is used to solve the model and obtain the Pareto front solution set. Subsequently, three optimal parameter configurations were selected for simulation analysis and experimental platform construction. The simulation and experimental results indicate that the veneer repair time ranges from 0.6 to 1.8 seconds, depending on the stamping speed. A reduction of 28 mm in die height decreases the repair time by approximately 0.1 seconds, resulting in an efficiency improvement of about 14%. The experimental results confirm the effectiveness of the proposed method in repairing veneer defects. Vibration measurements further verify the system’s stable operation under parametric modeling and optimization design. The main vibration response occurs during the meshing and disengagement phases between the gear and rack.